Streamliner

A streamliner is a vehicle incorporating streamlining in a shape providing reduced air resistance. The term is applied to high-speed railway trainsets of the 1930s to 1950s, and to their successor " bullet trains". Less commonly, the term is applied to fully faired upright and recumbent bicycles. As part of the Streamline Moderne trend, the term was applied to passenger cars, trucks, and other types of light-, medium-, or heavy-duty vehicles, but now vehicle streamlining is so prevalent that it is not an outstanding characteristic. In land speed racing, it is a term applied to the long, slender, custom built, high-speed vehicles with enclosed wheels.

Trains

Before World War II

Europe

The first high-speed streamliner in Germany was the " Schienenzeppelin", an experimental propeller driven single car, built in 1930. On 21 June 1931, the car set a speed record of on a run between Berlin and Hamburg. In 1932 the propeller was removed and a hydraulic system installed. The Schienenzeppelin made in 1933.

The Schienenzeppelin led to the 1932 construction of the diesel-electric DRG Class SVT 877 "Flying Hamburger". This two-car train set had 98 seats and a top speed of . In regular service with the Deutsche Reichsbahn, starting on 15 May 1933, this train ran the between Hamburg and Berlin in 138 minutes with an average speed of .

The SVT 877 was the prototype for the DRG Class SVT 137, first built in 1934/1935 for use in the FDt express train service. In test drives, the SVT 137 "Bauart Leipzig" set a world speed record of in 1936. The fastest regular service with the SVT 137 was between Hannover and Hamm with an average speed of . This service lasted until 22 August 1939.

In 1935, Henschel & Son, a major manufacturer of steam locomotives, introduced the 4-6-4 DRG Class 05 high speed streamliner locomotives for use on the ''Deutsche Reichsbahn'' Frankfurt am Main to Berlin route. Three examples were built in 1935–36.

Built for top speeds of over , the DRG Class 05 locomotives soon proved much faster in test runs. The DRG 05-002 made seven runs in 1935–36 during which it attained top speeds of more than with trains up to weight.

On 11 May 1936, the DRG 05-002 set the world speed record for steam locomotives after reaching on the Berlin–Hamburg line while hauling a train. The locomotive's engine power was more than .

On 30 May 1936, the DRG 05-002 set an unbroken start-stop speed record for steam locomotives. During the return run from a 190 km/h test on the Berlin-Hamburg route it did the ~ from Wittenberg to a signal stop before Berlin-Spandau in 48 min 32 s, meaning average between start and stop.

The DRG 05-002 was for a time the official holder of the world top speed record for steam locomotives. The British London and North Eastern Railway (LNER) Class A4 4468 ''Mallard'' locomotive broke that record two years later.

In the United Kingdom, development of streamlined passenger services began in 1934. The Great Western Railway introduced relatively low-speed streamlined railcars, while the London and North Eastern Railway (LNER) introduced the "Silver Jubilee" service using streamlined A4 class steam locomotives and full length trains rather than railcars.

In 1938, the LNER locomotive ''Mallard'', which had been built for "Silver Jubilee" service, set on a test run a still unsurpassed official record for the highest top speed attained by a steam locomotive, . Soon afterwards, the London, Midland and Scottish Railway introduced the Princess Coronation Class streamlined locomotives shortly before World War II began in 1939.

Starting in 1934, the Italian State Railways ( Ferrovie dello Stato (FS)) developed the FS Class ETR 200, a three-unit electric streamliner. The first of those trains entered revenue service in 1937.

On 6 December 1937, an ETR 200 made a top speed of between Campoleone and Cisterna on the run Rome-Naples. In 1939 the ETR 212 made . The journeys from Bologna to Milan were made in 77 minutes, meaning an average of .

In the Netherlands, Nederlandse Spoorwegen (NS) introduced in 1934 the Materieel 34 (DE3), a three unit streamlined diesel-electric trainset. An electric version, Materieel 36, went into service in 1936.

The similar electric Materieel 40 was first built in 1940. The NS also developed in the 1930s a streamlined version of the class 3700/3800 steam locomotive, nicknamed "potvis" (sperm whale).

The "Dieselvijf" (DE5), a top speed five unit diesel-electric trainset based on DE3, completed the Dutch streamliner fleet in 1940. In test runs, a DE5 ran

On the occasion of the twentieth anniversary of the October Revolution, the Soviet Kolomna Locomotive Factory produced two examples of the wind-tunnel designed SŽD series 2-3-2К (4-6-4 Whyte Notation) streamliner locomotive for Moscow-Leningrad service. In testing, it was shown capable of speeds greater than (170 km/h or 105 mph in test ride), and it entered service in 1938. Production of the series was canceled with the onset of World War II.

In the 1930s, streamlined Luxtorpeda diesel units that Austrian and later Polish manufacturers constructed were reaching speeds of up to in Poland. In 1937 the first Polish streamlined steam locomotive Pm36-1 (140 km/h) pulled the Nord Express between Poland and France (Paris). This locomotive was awarded golden medal in the World Expo in Paris in 1937.

In Czechoslovakia in 1934, Czechoslovak State Railways ordered two motor railcars with maximum speed . They were constructed by Tatra company, which was producing the first streamlined mass-produced automobile Tatra 77 at that time. The railcar project was led by Tatra chief designer Hans Ledwinka and received streamlined design by Paul Jaray. The railcars were unique thanks to the patented transmission system invented by Josef Sousedík – at lower speeds, it worked like petrol-electric transmission and at around it automatically switched to direct mechanical transmission without any gear. Thanks to this the railcars had good acceleration, low fuel consumption and were easy to drive.

Both ČSD Class M 290.0 were delivered in 1936, one of them reached during a test run. They were run on the Czechoslovak prominent route Bratislava-Prague under " Slovenská strela" ( Slovak for "Slovak Arrow") brand.

United States

The earliest known streamlined rail equipment in the United States were McKeen rail motorcars that the company built for the Union Pacific and the Southern Pacific Railroads between 1905 and 1917. Most McKeen cars sported a pointed "wind splitter" front, a rounded rear and round porthole style windows in a style that was as much nautically as aerodynamically inspired.

The McKeen cars were unsuccessful because the internal combustion drive technology for that application was unreliable at the time. Further, the lightweight frames dictated by the cars' limited power tended to break. Streamlined rail motorcars would appear again in the early 1930s after the internal combustion-electric propulsion technology that General Electric developed and that the Electro-Motive Company (EMC) promoted became the accepted technology for use rail motorcars in the 1920s.

Streetcar builders sought to build electric cars with improved speed for interurban lines through the 1920s. In 1931, the J. G. Brill Company introduced the Bullet, a lightweight, wind-tunnel designed car with a rounded front that could run either singly or in multiple-unit sets, capable of speeds over . Although Depression-era economics cut into sales, the design was highly successful in service, lasting into the 1980s.

In 1925, the recently-formed Pullman Car & Manufacturing Corporation experimented with lightweight self-propelled railcars in co-operation with the Ford Motor Company concurrent with Ford's development of its Trimotor aircraft. In 1931, Pullman enlisted the services of the Trimotor design contributor William Bushnell Stout to apply airplane fuselage design concepts to railcars.

The result was the ''Railplane'' (not the ''Bennie Railplane''), a streamlined self-propelled railcar with a tapered cross-section, lightweight tubular aluminum space frame and duralumin skin. In testing with the Gulf, Mobile and Northern Railroad in 1932, it reportedly reached .

The Union Pacific had been seeking improvements to self-propelled railcars based on European design ideas. The performance of the ''Railplane'' encouraged the railroad to increase its efforts in partnership with Pullman-Standard.

In 1931, the Budd Company reached an agreement with the French tire company Michelin to produce pneumatic-tired rail motorcars in the US, as an improvement on the heavy, underpowered and shimmy-prone " doodlebugs" that ran on American tracks. In that endeavor, Budd would produce lightweight rail equipment utilizing unibody construction and the high strength alloy stainless steel, enabled by shot welding, a breakthrough in electrical welding technique. The venture produced articulated power-trailer car sets with streamlined styling, which left the Budd Company just a (much) more powerful engine away from producing a history-making streamlined trainset.

The Great Depression caused a catastrophic loss of business for the rail industry as a whole and for manufacturers of motorized railcars whose primary markets, branch line services, were among the first to be cut. The interests of lightweight equipment manufacturers and rail operators therefore focused on the development of a new generation of lightweight, high speed, internal combustion-electric powered streamlined trainsets that were primarily designed for mainline service.

The Chicago, Burlington & Quincy Railroad (Burlington) and the Union Pacific sought to increase the efficiency of their passenger services by looking to the lightweight, petroleum-powered technology that Budd and Pullman-Standard were developing. The Union Pacific named its project the '' M-10000'' (designated first as ''The Streamliner'' and later as the ''City of Salina'' when in revenue service from 1935 to 1941).

The Burlington initially named its first train the '' Burlington Zephyr''. The two railroads' trains each entered service as three-car articulated sets (including the power car).

The Winton Engine Corporation, a subsidiary of General Motors (GM), manufactured the engines for both locomotives. The prime mover for the ''Burlington Zephyrs diesel-electric propulsion was a new 600 hp diesel engine. The Union Pacific's ''M-10000'' had a 600 hp spark-ignition engine that ran on "petroleum distillate", a fuel similar to kerosene.

The two trainsets were star attractions at the 1934 World's Fair (" A Century of Progress") in Chicago, Illinois. During its set's demonstration period, the Union Pacific named the ''M-10000'' as the ''Streamliner'', providing the first use of the term with respect to trains. The ''Streamliner''s publicity tour in February–May 1934 attracted over a million visitors and gained attention in national media as the herald of a new era in rail transportation.

On 26 May 1934, the Burlington's ''Zephyr'' made a record-breaking "Dawn to Dusk" run from Denver, Colorado, to Chicago for its grand entry as a Century of Progress exhibit. The ''Zephyr'' covered the distance in 13 hours, reaching a top speed of and running an average speed of . The fuel for the run cost US$14.64 at 4¢ per U.S. gallon (equivalent to $ and $ per gallon respectively in after inflation).

The Burlington's event was covered live on radio and drew large, cheering crowds as the "silver streak" zipped by. Adding to the sensation of the ''Zephyr'' were the striking appearance of its fluted stainless steel bodywork and its raked, rounded, aerodynamic front end that symbolized its modernity. The train's design echoed in steam locomotive styling throughout the following years.

After its Worlds Fair display and a nationwide demonstration tour, the ''Zephyr'' entered revenue service between Kansas City, Missouri, and Lincoln, Nebraska, on 11 November 1934. A total of nine ''Zephyr'' trainsets were built for the Burlington between 1934 and 1939. Each ran as named trains on various Burlington midwestern routes.

The Burlington later renamed the ''Burlington Zephyr'' as the '' Pioneer Zephyr'' in honor of that train's status as the first of the fleet. In April 1935, two ''Twin Cities Zephyrs'' that bore the same three-car configuration entered service on the railroad's Chicago and Minneapolis-St. Paul route.

Larger trainsets with more powerful Winton engines were built for the Burlington and put into service over longer routes. Twin-engine power units and eventually booster power units met the trainsets' additional power requirements. The Burlington's four-car '' Mark Twain Zephyr'' entered revenue service in October 1935 on the railroad's Saint Louis – Burlington, Iowa, route.

Two partially-articulated six-car trainsets entered service in May 1936 on the Burlington's '' Denver Zephyr'' route, which connected Chicago and Denver. The Burlington then replaced those sets with a pair of partially-articulated ten-car trainsets in November 1936. The Burlington moved the ''Denver Zephyr''s six-cat sets to the ''Twin Cities Zephyr'', transferring that train's original streamlined cars to other Burlington routes.

The last of the classic ''Zephyrs'' was built for the Burlington's Kansas City – Saint Louis '' General Pershing Zephyr'' route. That trainset, which contained GM's newest 1000 hp engine and conventional coupling, entered service in June 1939.

The Burlington's original ''Zephyr'' trainsets remained in service in the postwar era. The railroad retired the last of its six-car sets in 1968 after using it as the '' Nebraska Zephyr''.

On 31 January 1935, the Union Pacific's three-car ''M-10000'' went into service between Kansas City, Missouri, and Salina, Kansas, as ''The Streamliner''. The train subsequently became the ''City of Salina'' under the railroad's naming convention for its expanding fleet of diesel-powered streamliners.

The Union Pacific operated the ''M-10000'' as a three-car set until the railroad was retired the set in 1941. The trainset's 1942 scrapping provided Duralumin that was recycled for use in war-time military aircraft.
The Union Pacific also commissioned the construction of five modified trainsets that had evolved from the initial ''M-10000'' design. Those streamlined trains inaugurated the railroad's high-speed service out of Chicago while bearing the names '' City of Portland'' (June 1935), ''City of Los Angeles'' (May 1936), '' City of San Francisco'' (June 1936) and '' City of Denver'' (June 1936).

The '' M-10001'' set had a single power unit that contained a 1200 hp Winton diesel engine. The power unit pulled six tapered low-profile cars that had the form of the original three-car ''M-10000'' trainset. The '' M-10002''s set consisted of a 1200+900 hp cab/booster locomotive pulling nine cars of the same form.

Automotive-styled cab/booster locomotive sets with 1200 hp engines powered the Union Pacific's ''City of San Francisco'' and ''City of Denver'' sets. The two ''City of Denver'' sets started service two cars shorter than the ''M-10002'' and ''M-10004'' sets, with roomier and heavier straight-sided cars.

The Union Pacific's initial streamliner service to the west coast consisted of five runs monthly for each route. The railroad maintained its daily overnight service on the Chicago – Denver run by assigning three locomotive sets for two trains. The railroad then augmented that stable with locomotive equipment taken from other runs.

Despite the breakthrough schedule times of the long-distance M-1000x "City" trains, the records of the Union Pacific's fleet reflected the limitations of the locomotives' technology when meeting the demands of long-distance and higher capacity service. The ''M-10001'' ran for only 32 months as the ''City of Portland'' before it was replaced, re-entered service on the Portland – Seattle run and retired in June 1939.

Similarly, the ''M-10002'' spent 19 months as the Union Pacific's ''City of Los Angeles'', 39 months as the ''City of Portland'' and ten months out of service starting in July 1941. The locomotive then served on the Portland – Seattle run until the railroad took it out of service again in March 1943. After running for 18 months as the ''City of San Francisco M-10004'', the locomotive spent six months being refurbished and then served from July 1938 as a second unit on the ''City of Los Angeles''. The Union Pacific retired the locomotive in March 1939.

The Union Pacific converted the ''M-10001'' and ''M-10004'' power units to additional boosters for the ''City of Denver'' trains. The train's cars then became spare equipment. The two ''City of Denver'' trainsets (''M–10005'' and ''M–10006), after cannibalizing power from the ''M-10001'' and ''M-10004'', remained in service until 1953.

Class GG1 electric locomotives brought streamlined styling to the Pennsylvania Railroad's fleet of electric locomotives in late 1934. Meanwhile, the Boston and Maine's '' Flying Yankee'', identical to the original ''Zephyr,'' entered service between Boston and Portland, Maine, on 1 April 1935.

The Gulf, Mobile and Northern Railroad '' Rebel'' trainsets were similar to the ''Zephyr'' in form, but were not articulated. Designed by Otto Kuhler, the ALCO powered diesel-electrics that the American Car and Foundry Company constructed were placed into service on 10 July 1935.

While streamlining on steam locomotives was more about marketing than performance, newly designed locomotives with state-of-the-art steam technology were able to travel at high speeds. The Milwaukee Road class A Atlantics, built in 1935 to compete with the ''Twin Cities Zephyr'', were the first "steamliners" equipped to back up their styled claim to extra speed. In a 15 May 1935 run by locomotive #2 and a dynamometer car, the railroad documented a top speed of .

This was the fastest authenticated speed reached by a steam locomotive at the time, making #2 the rail speed record holder for steam and the first steam locomotive to top . That record lasted until a German DRG Class 05 locomotive exceeded it the following year.

The '' Illinois Central 121'' trainset was the first of the '' Green Diamond'' streamliners running between Chicago and St Louis. It was a five-unit (including power car) articulated trainset for day service. The Pullman-built set had the same power format and 1200 hp Winton diesel engine as ''M-10001,'' with some style aspects that resembled the later M1000x trainsets.

The Illinois Central ran the 121 trainset on the ''Green Diamond'' from May 1936 to 1947. After an overhaul, the railroad placed the set on the Jackson Mississippi – New Orleans run until it retired and scrapped the set in 1950.

The visual styling of the new trainsets made the existing fleets of locomotives and railcars suddenly look obsolete. Rail lines soon responded by adding streamlined shrouding and varying degrees of mechanical improvement to older locomotives and re-styling heavyweight cars.

The first American steam locomotive to receive that treatment was one of the New York Central Railroad's (NYC's) J-1 Hudson class locomotives built in 1930, which was re-introduced with streamlined shrouding and named the ''Commodore Vanderbilt'' in December 1934. The ''Vanderbilt'' styling was a one-off design by Carl Kantola.

The NYC's next venture in streamlined styling was Henry Dreyfuss' 1936 full-length exterior and interior design of the railroad's '' Mercury'' trainsets. Raymond Loewy also designed in 1936 art-deco shrouding with a bullet-front scheme for the Pennsylvania Railroad's class K4 locomotives.

In 1937, Otto Kuhler used a variation of the bullet-front design on a 4-6-2 locomotive constructed for the Baltimore & Ohio's streamlined ''Royal Blue''. Henry Dreyfuss used a similar variation for the J-3a ''Super Hudsons'' that pulled the '' 20th Century Limited'' and other NYC express trains.

In 1937, the Milwaukee Road introduced the class F7 Hudsons on the '' Twin Cities Hiawatha'' run. The Hudsons could cruise above and were said to exceed on occasion. Otto Kuehler designed the Milwaukee Road's speedsters with "shovel nose" styling. Some of the class 7's details were evocative of those of the ''Zephyrs''.

Also in 1937, the Electro-Motive Corporation (EMC) (later incorporated into GM's Electro-Motive Division (EMD)) started production of streamlined diesel-electric passenger locomotives, incorporating the lightweight carbody construction and raked, rounded front end introduced with the ''Zephyr'' and the high-mounted, behind-the-nose cab of the M-1000x locomotives. One of the first, EMC's TA, was a 1200-hp version produced for the Rock Island Rockets, a series of six lightweight, semi-articulated three and four-car trainsets.

EMC/EMD manufactured streamlined E-unit diesel-electric locomotives from 1937 to 1963. These incorporated two features of the earlier EMC 1800 hp B-B development design locomotives, the twin-engine format and multiple-unit control systems that facilitated cab/booster locomotive sets.

The E-units brought sufficient power for full-sized trains such as the B&O '' Capitol Limited, the ''Atchison, Topeka and Santa Fe Railway's (AT&SF's) '' Super Chief,'' and the Union Pacific's upgraded ''City of Los Angeles'' and '' City of San Francisco,'' which challenged steam power in all aspects of passenger service. EMC introduced standardized production to the locomotive industry, with its attendant economies of scale and simplified processes for ordering, producing and servicing locomotives. As a result, EMC was able to offer a variety of support services that decreased technological and initial cost barriers that would otherwise deter conversions to diesel-electric power.

With power and reliability of new diesel-electric units improved with the 2000 hp EMC E3 locomotive in 1938, the advantages of diesel became compelling enough for a growing number of rail lines to select diesel over steam for new passenger equipment. The power and top speed advantages of state-of-the-art steam locomotives were more than offset by diesel's advantages in service flexibility, downtime, maintenance costs and economic efficiency for most operators.

The American Locomotive Company (ALCO), the builder of the Hiawatha speedsters, saw diesel as the future of passenger service and introduced streamlined locomotives influenced by the design of the E units in 1939. The replacement of steam with diesel power was interrupted by the US entry into World War II, with a military premium on diesel technology that stopped all production of diesel locomotives for passenger service between September 1942 and January 1945.

Streamlined steam locomotives continued to be produced into the early postwar era. Among the most distinctive were the Pennsylvania Railroad's duplex-drive 6-4-4-6 type S1 and 4-4-4-4 type T1 locomotives that Raymond Loewy styled.

In terms of service longevity, the most successful were the Southern Pacific GS-3 ''Daylight'' locomotives introduced in 1938 and the Norfolk and Western class J locomotives introduced in 1941. In contrast to designs that completely encased the boiler in shrouding, streamlining of the GS-3/GS-4 series locomotives consisted of skyline casing flush with the smokestack and smoke-lifting skirting along the boiler that left the silver-painted smokebox on full display.

Japan

The trend of streamliners also came to Japan. In 1934, the Ministry of Railways (Japanese Government Railways, JGR) decided to convert one of its 3-cylinder steam locomotives class C53 into a streamlined style. The selected locomotive was No.43 of class C53. However Hideo Shima, the chief engineer of the conversion, thought streamlining had no practical effect on reducing air resistance, because Japanese trains at that time did not exceed a speed of .

Shima therefore designed the locomotive to create airflow that lifted exhaust smoke away from the locomotive. He had expected no practical effect on reducing air resistance completely, therefore he never tried to test fuel consumption or tractive force of the converted locomotive. The Japanese government planned to use this one converted streamline locomotive on the passenger express route between Osaka and Nagoya.

The converted locomotive gained much popularity from the public. JGR therefore decided to build 21 new streamlined versions of the class C55 locomotive^(Japanese). Additionally, JGR built 3 streamlined class EF55 electric locomotives. Kiha-43000 diesel multiple units and Moha-52 electric multiple units also received a streamlined style.

The South Manchuria Railway, which was under Japanese control at that time, also designed the Pashina class streamlined locomotive. The Railway operated the Asia Express, whose style was coordinated with that of Pashina locomotives.

These streamlined steam locomotives took many man-hours to repair due to their casing. After the outbreak of World War II, the lack of an experienced labor force made the problems worse. As a result, many of the locomotives had their casings removed.

Australia around World War II

Streamliner locomotives arrived relatively late in Australia. In 1937 streamlined casings were fitted on four Victorian Railways S class locomotives for the Spirit of Progress service between Melbourne and Albury. Similar casings were then fitted on two Tasmanian Government Railways R class narrow-gauge locomotives for the Hobart to Launceston expresses.

Despite — or perhaps because of — the strategic priorities of World War II, some new streamliner locomotives were built in Australia during and immediately after the war. The first five New South Wales C38 class locomotives were modestly streamlined with distinctive conical noses, while the twelve South Australian Railways 520 class locomotives featured extravagant streamlining in the style of the Pennsylvania Railroad's T1.

In all cases, the streamlining on Australian steam locomotives were purely aesthetic, with negligible impacts on train speeds.

After World War II

Europe

In Europe, the streamliner tradition gained new life after World War II. In Germany, DRG Class SVT 137 trains resumed service, but at slower speeds than before the war. Based on the Kruckenberg SVT 137, the Deutsche Bundesbahn's (DB's) streamlined diesel-electric Class VT 11.5 (later renamed to DB Class 601) built in 1957 was used as the " Trans Europ Express (TEE)" for international high-speed trains.

From 1965, the DB used the streamlined electric locomotives DB Class 103 with regular trains for high-speed service. From 1973, the DB used the DB Class ET 403, a fully streamlined four-unit electric train with tilting technology. In East Germany, the DR Class VT 18.16 was built for international express service.

The Swiss SBB and the Dutch NS developed five diesel-electric RAm TEE I (Swiss) and NS DE4 (Dutch) trainsets for their Zurich-Amsterdam and Amsterdam-Brussels-Paris routes. The SBB sold four of these trainsets to the Canadian Ontario Northland Railway (ONR) in 1997. The ONR then operated the trains on its Toronto–Moosonee line as the Northlander.

From 1961, the SBB used for TEE service the RAe TEE II, a set of five streamlined electric trains compatible with four different railway electrification systems. Italy used pre-war trains and new trains that the Italian State Railways (Ferrovie dello Stato (FS)) developed. The new trains included the FS Class ETR 250 ("Arlecchino"), the ETR 300 ("Settebello"), the ETR 401 ("Pendolino"), the ETR 450 ("Pendolino") and the ETR 500.

Streamliner service temporarily ended in the United Kingdom with the outbreak of WWII. During the war, the LNER and LMS streamlined locomotives had part of their streamlining removed to aid maintenance. By the late 1940s and early 1950s, the state of the railways was improving as deteriorated track conditions caused by delayed maintenance work were corrected. The repairs and new improvements enabled the railways to provide additional mainline trackage for high speed trains.

The first experiments with diesel streamliner services in the United Kingdom were the Blue Pullman trains introduced in 1960 and withdrawn in 1973. These provided luxury business services, but were marginally successful and ran only a little faster than mainstream services. The Blue Pullman was followed by research into streamlined trains and tilting trains which led to the iconic InterCity 125 ( Class 43) offering train services across the United Kingdom.

High-speed service with the ICE 1 (Class 401) began in 1991. The train, which has traveled at speeds of up to in revenue service, broke a speed record that the first "Flying Hamburger" had set 60 years earlier when traveling between Hamburg and Berlin from 1933.

A TGV high-speed test train set a world record for the fastest wheeled train, reaching in 2007. Conventional TGV services operate at up to on the LGV Est, LGV Rhin-Rhône and LGV Méditerranée. The power cars of the TGV Euroduplex (2N2), which began commercial operations in 2011, have a more streamlined nose than do previous TGVs.

In 2015, '' Eurostar'' began to operate the electric multiple unit (EMU) British Rail Class 374, also known as the Eurostar e320, on its high-speed services through the Channel Tunnel. The train serves destinations beyond ''Eurostar's'' core routes to the Gare du Nord station in Paris and the Brussels-South railway station. Owned by Eurostar International Limited and capable of operating at , the aluminum trains are sixteen-unit versions of the Siemens Velaro.

United States

High-speed steam service continued in the United States after World War II, but became increasingly uneconomical. The New York Central's Super Hudsons went out of service in 1948 as the line converted to diesel for passenger service. The Milwaukee Road retired its high speed Hiawatha steam locomotives between 1949 and 1951. The last of the Pennsylvania Railroad's short-lived T1 class locomotives went out of service in 1952. All of those iconic locomotives were scrapped. The last steam streamliners built were three Norfolk and Western class J locomotives in 1950, which operated until 1959.

In 1951, the Interstate Commerce Commission implemented regulations restricting most trains to speeds of or below unless automatic train stop, automatic train control, or cab signalling were installed. The new regulations minimized one of the key advantages of rail travel over the automobile, which became an increasingly attractive alternative as postwar construction of highway systems progressed. Rail operators marketed their services on the basis of luxurious sightseeing, as airlines increasingly competed with rail lines for long-distance travel.

In the mid-1950s, there were several attempts to revive the lightweight custom streamliner concept. None of these projects achieved any lasting impact on passenger service.

The ''Train X'' project, first promoted by Robert R. Young no later than 1948, resulted in low-profile Baldwin RP-210 locomotives paired with articulated aluminum cars from Pullman-Standard. Two trainsets were built in 1956 for the New York Central Railroad's '' Ohio Xplorer'' and the New York, New Haven and Hartford Railroad's '' Dan'l Webster''. The pair were problematic and were withdrawn from service by 1960.

GM's project, originally called ''Train Y'', was marketed as the '' Aerotrain''. It featured a futuristic, automotive-styled EMD LWT12 diesel–electric locomotive pulling aluminum coaches adapted from GM's long-distance bus design.(1)
(2)
(3) ''In''
(4) 10:39 minutes video showing internal and external views of a demonstration ''Aerotrain'' traveling at speeds of up to per hour as Pennsylvania Railroad No. 1000 and external views of ''Aerotrain'' No. 1001 traveling on the Sacramento Northern Railway. Two trainsets were produced in 1955 and were trialed by several railroads, but no orders were forthcoming. The two demonstration units were eventually sold to the Rock Island Line, which was already operating an EMD LWT12 paired with Talgo II cars from ACF Industries as the ''Jet Rocket''. Rock Island operated them in commuter service until 1966.

The ''Speed Merchant'' project also produced only two examples. They consisted of Fairbanks-Morse P-12-42 locomotives paired with Talgo II cars from ACF Industries, and were used by the Boston and Maine Railroad for commuter service and by the New York, New Haven and Hartford Railroad's ''John Quincy Adams''. Both were retired by 1964.

In 1956, the Budd Company produced a single streamlined, lightweight, six car DMU trainset that the New York, New Haven and Hartford Railroad operated as the '' Roger Williams''. After a short period of time in high speed service, the train was split up and the cars were used in service with the New Haven's other RDCs.

The advent of jet air travel in the late 1950s brought forth a new round of price competition from airlines for long-distance travel, severely affecting the ridership and profitability of long-distance passenger rail service. Government regulations forced railroads to continue to operate passenger rail service, even on long routes where, the railroads argued, it was almost impossible to make a profit.

Unlike air and automotive infrastructure, which federal and state governments subsidize, operating revenues entirely support privately-owned rail infrastructure in the United States. By the late 1960s, most rail operators were therefore seeking to completely discontinue passenger service.

The lightweight custom streamliner concept was revived again in the 1960s with the UAC TurboTrain. These articulated trainsets used gas turbine engines instead of reciprocating diesel engines for traction power. They were operated by Penn Central and then Amtrak from 1969 to 1976, and in Canada by Canadian National and then Via Rail from 1969 to 1982.

Some GG1 electric locomotives that the Pennsylvania Railroad once operated remained in service until 1983. The last EMD E-units in regular service were retired in 1993.

Amtrak has operated nearly all long-distance passenger rail systems in the United States since 1971. The publicly-financed rail company's quest for greater fuel efficiency has led them to acquire and operate GE Genesis diesel-electric locomotives. In so doing, Amtrak reintroduced the lightweight, aerodynamic carbody construction that the ''Zephyr'' had pioneered in the 1930s.

Since 2000, Amtrak has operated high-speed '' Acela'' (named ''Acela Express'' until 2019) passenger trains that travel at speeds of up to in the Boston - Washington, D.C. Northeast Corridor. State governments and others in many areas throughout the United States have considered the construction of new high-speed lines, but rail travel is much less common in the U.S. than in Europe or Japan.

In 2008, California voters approved bonds to initiate construction of the California High-Speed Rail line, which would connect the San Francisco Bay Area, the Central Valley and Southern California. Construction of the first segment, between Bakersfield and Merced in the Central Valley, began in 2015.

=Preserved examples (United States)

=

After 26 years of service and traveling over , the '' Pioneer Zephyr'' went to Chicago's Museum of Science and Industry. The '' Flying Yankee'', the third streamliner to enter service, is undergoing restoration to operational condition. The ''Silver Charger'' locomotive of the '' General Pershing Zephyr'' trainset remained in service until 1966 and is also undergoing restoration.

In December 1974, the streamlined steam-powered Southern Pacific 4449 "Daylight" came off an outdoor public display to undergo a restoration and re-painting that enabled it pull the '' American Freedom Train'', which toured the 48 contiguous United States as part of the nation's 1976 Bicentennial celebration. With the exception of occasional interruptions for maintenance and inspections, the restored locomotive has operated in excursion service throughout that area since 1984.

The twice-restored streamlined Norfolk and Western Railway's steam-powered class J1 locomotive Number 611 operated in excursion service within the United States from 1982 to 1994 and from 2015 to 2017. The locomotive has traveled for display at special events.

Examples of the pre-World War II "slant nose" EMC EA, E3, E5, and E6 locomotives are on display at the Baltimore and Ohio Railroad Museum, the North Carolina Transportation Museum, the Illinois Railway Museum, and the Kentucky Railway Museum. The stainless steel clad E5 is occasionally matched with one of the original '' Denver Zephyr'' car sets for excursion service. As of 2017, the Rock Island No. 630 E6 unit was under restoration for display in Iowa.

The EMD LWT12 locomotives and several passenger cars of GM's two ''Aerotrains'' are presently on display within the United States. The National Railroad Museum in Green Bay, Wisconsin now exhibits the Chicago, Rock Island and Pacific Railroad's ''Aerotrain'' locomotive No. 2 and two passenger cars. The National Museum of Transportation in Kirkwood, Missouri (near St. Louis) exhibits the Rock Island's locomotive No. 3 and two passenger cars.

Japan

After World War II, Japanese railroads favored multiple unit trains, even on their mainlines. In 1949, the Japanese National Railways (JNR) released the 80 series EMUs for use on long-distance trains. Lead coaches of the 80 series built after 1950 incorporated a streamlined design.

In 1957, Odakyu Electric Railway released the 3000 series EMUs. The exterior design was developed using a wind tunnel intended for aircraft.

An Odakyu 3000 set a world railway speed record of () for a narrow-gauge train. Multiple unit trains were thus shown to be suitable for long-distance trains by the JNR Series 80 and for high-speed trains by the Odakyu 3000.

These experiences led to the development of the first Shinkansen, the 0 Series. The Odakyu 3000 strongly influenced the 0 series, which was also developed using a wind tunnel.

The lead coaches of the 0 series were developed using a Douglas DC-8 for a reference. At a speed of , the aerodynamic style of the 0 series "bullet train" had a substantial effect on reducing air resistance.

In 2020, the Central Japan Railway Company (JR Central) began operating the N700S, the most recent addition to the N700 Series Shinkansen. The 16-car train reached its design speed of in trials conducted in 2019 on the Tokaido Shinkansen.

The JR Central is presently developing and testing the L0 series high-speed maglev train. The JR Central plans to use the streamlined train on the Chūō Shinkansen railway line between Tokyo and Nagoya, which is under construction. The railroad expects to open the line in 2027 and to later extend it to Osaka.(1)
(2)

A seven-car L0 series train set a world railway speed record of 374 mph (603 km/h) in 2015. The railway plans to operate the train at a maximum speed of 310 mph (500 km/h) when in revenue service. The train's speed would exceed that of the world's fastest commercial electric train, the Chinese Shanghi maglev, whose cruising speed is 268 mph (431 km/h).

High speed train services today

Worldwide many, if not most, high speed passenger trains are now streamlined. Speeds continue to rise as high-speed rail services become the normal long-distance rail service.

Specific trainsets

Streetcars and high-speed interurbans

Early versions of the PCC (Presidents’ Conference Committee) streetcars were referred to as ''Streamliners'' in North America. However, aerodynamic research appeared much earlier on the interurban scene, i.e. among the forerunners of the recent light rail. In 1905, the Electric Railway Test Commission started a series of test runs to develop a carbody design that would reduce wind resistance at high speeds.

Vestibule sections of different shapes were suspended independent of the carbody, with a dynamometer to measure the resistance of each. Over 200 test runs were made at speeds up to 70 mph (c. 112 km/h) with parabolic, wedge, standard, and flat vestibule ends.

The test results indicated that a parabolic-shaped front end reduced wind resistance at high speeds below that of the conventional rounded profile. However, with that time's heavy railcars and moderate speeds, no significant operating economies were realized. Streamlining was discarded for another quarter-century.

From the 1920s, however, stronger alloys, lightweight metals, and better design were all used to reduce carbody weight – which in turn permitted the use of smaller bogies and motors with corresponding economies in power consumption. In 1922, the G. C. Kuhlman Car Company built ten lightweight cars for the Western Ohio Railway.

After an elaborate wind tunnel investigation, the first in the railway industry, the J. G. Brill Company made in 1931 its first Bullet railcars, capable to speeds above 90 mph (145 km/h). With 52 seats, they weighed only 26 tons. Some remained in use for almost 60 years.

Buses

Many buses adopted a stylish streamline look in the 1930s with tests showing that streamlined design reduced fuel costs.

Starting in 1934, Greyhound Lines worked with the Yellow Coach Manufacturing Company for its Series 700 buses, first for ''Series 719'' prototypes in 1934, and from 1937 as the exclusive customer for Yellow's ''Series 743'' buses. Greyhound named these the "Super Coach" and purchased a total of 1,256 between 1937 and 1939.

General Motors also custom-built twelve streamlined Futurliners for its 1936 ''Parade of Progress'' and, later the 1939 New York World's Fair and traveling exhibits. The popular two-level GMC PD-4501 Scenicruiser, which GM manufactured for Greyhound Lines between 1954 and 1956, exemplified the further streamlining that occurred in the company's bus designs in the years that followed World War II.

Automobiles

Beginning in the 1910s, engineers tried to incorporate aerodynamics into the shape of automobiles. Some such cars entered production.

Experimental and prototype vehicles

Chronologically:
*Persu car (1922–23), designed by Romanian engineer Aurel Persu, who improved on the Tropfenwagen by placing the wheels inside the car body
*Burney car (1929-1931), working prototypes designed by Dennis Burney and manufactured by Streamline Cars
* Dymaxion (1933–1934), U.S. "teardrop" car
* Stout Scarab (1932–35, 1946), aerodynamic US car
* Pierce Silver Arrow (1933), US concept car
* Porsche Type 32 prototype (1934), the model for the 1938 Volkswagen Beetle
* Schlörwagen (1939), German prototype aerodynamic car, never produced

Production vehicles

Many production automobiles have had streamlined bodies. Among these were, chronologically by first production year:
* Rumpler Tropfenwagen (1921), first aerodynamic "teardrop" car to be designed and serially produced (about 100 units built)
* Pontiac Economy Eight Series 601 (1933)
* Tatra 77 (1934), claimed to be the first truly serial-produced aerodynamic automobile
*Chrysler Airflow (1934) streamlined car
* Steyr 100 (1934) was presented to the public at the latest in January 1934, just like the Chrysler Airflow.
* Citroën Traction Avant (1934)
*Toyota AA (1935)
* Buick Roadmaster (1936)
* Lincoln-Zephyr (1936)
*Volkswagen Beetle (1938)
* International Harvester Metro Van (1938)
* Pontiac Torpedo (1940)
*Hudson Commodore (1941)
* Tucker 48 (1947), also known as Tucker Torpedo
* Saab 92 (1949)
* Cadillac Eldorado (1952)
*Chevrolet Corvette (1953)
* Citroen DS (1955)
* Edsel Citation (1958)
* Mercedes-Benz W111 (1959)
*General Motors EV1 (1996)

Record-setting streamlined racing cars

Racing cars setting world land speed records have extensive streamlining. These include:

Electric

* White Lightning: Electric-powered vehicle land speed record of 246 mph (395 km/h) (1999)
* Buckeye Bullet 3: Electric-powered vehicle land speed record of 341 mph (549 km/h) (2016)

Fuel cell

* Buckeye Bullet 2: Hydrogen fuel cell-powered vehicle land speed record of 286 mph (461 km/h) (2008)

Internal combustion

* Bluebird-Proteus CN7: Wheel-driven land speed record of 403 mph (649 km/h) (1964)
* Goldenrod: Wheel-driven land speed record of 409 mph (659 km/h) (1965)
* Spirit of Rett: Wheel-driven land speed record of (2010)
* Speed Demon: Wheel-driven land speed record of 439 mph (706.5 km/h) (2012)
* JCB Dieselmax: Diesel-powered land speed record of 350 miles per hour (560 km/h) (2006)

Rocket and jet

* Blue Flame (rocket): Land speed record of 622 mph (1,001 km/h) (1970)
* Thrust SSC (jet): Land speed record of 763 mph (1,228 km/h) (1997)

Trucks

Many small trucks and tractor units for pulling semi-trailer trucks have streamlining to improve aerodynamics.

Trailers

Camping (caravan) and animal trailer manufacturers use streamlining to make trailers easier to tow. Current and past manufacturers include Airstream, Avalon, Avion, Boles Aero, Bonair Oxygen, Curtis Wright, Knaus Tabbert, Silver Streak, Spartan, Streamline, and Vagabond.

Motorcycles

Land-speed records

Streamlined motorcycles setting land-speed records include:
* NSU Delphin I: 1951
* NSU Delphin III: 211 mph (340 km/h) (1956)
* Gyronaut X-1: 246 mph (395 km/h) (1966)
* Big Red: 253 mph (405 km/h) (1970)
* Silver Bird: 304 mph (489 km/h) (1975)
* Lightning Bolt: 319 mph (512.734 km/h) (1978)
* BUB Seven Streamliner: held record from 2006 to 2008 and again from 2009 to 2010
* Ack Attack: 376 mph (606 km/h) (2010)

Energy efficiency

Streamlined motorcycles designed to reduce energy usage include:
* Vetter Streamliner
* Craig Vetter Fuel Economy Challenge

Gallery of streamlined motorcycles

Bicycles and tricycles

Bicycle fairings help to streamline the vehicle and the rider. Human powered upright and recumbent bicycles and tricycles termed velomobiles that are partially or completely enclosed for aerodynamic advantage and weather protection take streamlining even further. Although many velomobiles are recreational, two-wheeled velomobiles have set a number of cycling speed records.

Ships

The Streamline Moderne–style automobile/passenger ferry '' MV Kalakala'' received its streamlining during a 1933–1935 reconstruction. The ship operated in Puget Sound near the northwestern coast of the U.S. state of Washington until 1967. It was scrapped in 2015.

Sterling Streamliner diners

Many American roadside diners built since the 1930s have had streamlined exteriors and interiors. In 1939, Roland Stickney designed a diner named the ''Sterling Streamliner''. Built by the John B. Judkins Company, a firm that also made custom car bodies, the prefabricated diner's production ceased in 1942 at the beginning of American involvement in World War II.

The rounded shapes of one or both ends of the ''Sterling Streamliner'' diners resembled the sloping curved nose of the ''Burlington Zephyrs streamlined silver locomotive.
One such ''Sterling Streamliner'' with two rounded ends was built in 1940 and installed as the ''Jimmy Evans Flyer'' in New Bedford, Massachusetts. In the 1960s, the building was moved to the village of Pocasset in the town of Bourne, Massachusetts, on Cape Cod, where it was named the ''My Tin Diner''.(1)
(2)
(3)
(4)
(5)
(6)

In 2000, an arsonist severely damaged the ''My Tin Diner'' when he set it on fire. In 2003, the structure was moved into a field next to the ''Handy Hill Creamery'' near Hix Bridge Road in Westport, Massachusetts, while plans were being made to restore it to working condition. However, although restoration began, it was not completed. Visible from the Road, the derelict structure was the only ''Sterling Streamliner'' with two rounded ends known to still survive in 2019.

Only one ''Sterling Streamliner'' was open for business in 2020: the Modern Diner in Pawtucket, Rhode Island. That structure, which was placed on the National Register of Historic Places in 1978, has both a rounded sloped end and a flat vertical end. Although the building's roof was once silver, it is now maroon.(1)
(2) an
photographs

(3)
(4)
(5)
(6)

Notes

References

Streamliners: America's Lost Trains
nbsp;– ''The American Experience''
*

External links

The interurban era
Middleton, William D. 1961, Fourth printing 1968, Kalmbach Publishing
All Aboard the Silver Streak: Pioneer Zephyr
exhibit at the Chicago Museum of Science and Industry.
* ''The Wilson Quarterly'' (on the Internet Archive)
Streamlined Transportation in the Art Deco Era
{{Webarchive, url=https://web.archive.org/web/20160304073421/http://www.louisvilleartdeco.com/feature/Transportation/feature-streamlinetransportation-index.html , date=4 March 2016  – Streamlining in the Cars, Trains and Planes of the 1930s.
"Driver's Cab is Placed at Front of Streamlined Engine" ''Popular Mechanics'', October 1934
bottom page 560

Locomotives
Automotive styling features