GE E60

The GE E60 is a family of six-axle C-C electric locomotives made by GE Transportation Systems (GE) between 1972 and 1983. The E60s were produced in several variants for both freight and passenger use in the United States and Mexico. GE designed the locomotive for use on the Black Mesa and Lake Powell Railroad (BM&LP), a dedicated coal-hauling route in Arizona, which began operation in 1973. That same year GE adapted the design for high-speed passenger service on Amtrak's Northeast Corridor. The largest customer was Ferrocarriles Nacionales de México (NdeM), the state-owned railroad in Mexico, which bought 39 for a new electrification project in the early 1980s.

The E60s were successful in the coal-hauling role. They ran on the BM&LP for decades and remain in use on several mining railroads in the Western United States. The passenger variants failed in their intended role. Problems with the truck design caused derailments above , rendering the locomotives unusable for high-speed service. By the end of the 1970s Amtrak abandoned the E60 in favor of EMD AEM-7 locomotives manufactured by Electro-Motive Division. In Mexico, the NdeM's project was delayed into the 1990s, then scrapped after three years of use. Most of the NdeM's electric locomotives never ran and were traded back to GE for diesels. Some were sold to various mining railroads.

Design

The Black Mesa and Lake Powell Railroad (BM&LP) was a new railroad built to transport coal from the Black Mesa Mine near Kayenta, Arizona to the Navajo Generating Station power plant at Page, Arizona. It was long and isolated from the national railroad network. The BM&LP was electrified at 50 kV 60 Hz AC, and was the first such electrification to use this voltage in the world. The railroad was intended to run as a conveyor belt, with trains cycling between the coal mine and the plant. To operate this conveyor belt, GE Transportation Systems (GE) designed the E60C, though it was suitable for general mainline freight operation.

The heavy loads of coal on BM&LP drove GE's design choices on the E60C. GE chose a six-axle (C-C) design, with wheels instead of the standard wheels. This was necessary because of the locomotive's 85:21 gearing. With this gearing a maximum speed of was possible, although the standard operating speed on the BM&LP was . A transformer steps down the high-voltage AC which is then rectified with thyristor bridges to provide DC power to six GE780 traction motors, one per axle. The locomotive is rated at , with a starting tractive effort of and a continuous tractive effort of . Physically the locomotive is long and weighs , including some of ballast.

GE made a number of changes when it redesigned the E60C for passenger use. The new design was lighter, at , and longer, at . A gearing of 68:38 permitted a maximum design speed of . The starting tractive effort was considerably lower at , with a continuous rating of . Unlike freight locomotives, passenger locomotives have to supply heat to passenger cars. In the 1970s Amtrak operated both old-style steam-heated cars and new Amfleet cars with head-end power (HEP). GE designed two variants to handle these use cases: the E60CP had steam generators, while the E60CH had HEP generators. Both models had a cab and pantograph at each end. Reflecting the varied electrification schemes on the Northeast Corridor the Amtrak units could operate at three different voltages: 11 kV 25 Hz AC, 12.5 kV 60 Hz AC, and 25 kV 60 Hz. The wheels had a more standard diameter of .

GE revised the design in the early 1980s for use by Ferrocarriles Nacionales de México (NdeM) on its new electrification project. The E60C-2, like the passenger variants, had double cabs and double pantographs. They were geared at 83:20, for a maximum speed of . Although geared differently from the E60CP/CH it also used wheels. The locomotives are long and weigh . They employ six GE 752AF traction motors. The tractive effort was similar to the original E60C: starting and continuous. NdeM adopted 25 kV 60 Hz electrification. A later buyer, the Deseret-Western Railway, like the Black Mesa and Lake Powell, adopted 50 kV 60 Hz AC.

History

Black Mesa and Lake Powell Railroad

The planned weight of a loaded coal train at the Black Mesa and Lake Powell (BM&LP) was . GE intended that the E60Cs work in multiple, three per train, to handle this load. The BM&LP ordered a total of six locomotives between 1972–1976, allowing it to operate two trains at once. The BM&LP acquired six former Ferrocarriles Nacionales de México E60C-2s after the latter discontinued electric operations in the late 1990s. These displaced the original E60Cs. The Arizona State Railroad Museum of Williams, Arizona took possession of ex-BM&LP E60C 6001 in 2010.

Amtrak and New Jersey Transit

Amtrak assumed control of almost all private sector intercity passenger rail service in the United States on May 1, 1971, with a mandate to reverse decades of decline. It retained approximately 184 of the 440 trains which had run the day before. To operate these trains, Amtrak inherited a fleet of 300 locomotives (electric and diesel) and 1190 passenger cars, most of which dated from the 1940s–1950s.

Operation on the electrified portion of the Northeast Corridor was split between the Budd Metroliner electric multiple units and PRR GG1 locomotives. The former suffered from poor reliability, and the latter were over 35 years old and restricted to . Amtrak faced a choice with the GG1s: completely rebuild the fleet, or replace them with a new locomotive. While no United States manufacturer had a dedicated electric passenger locomotive in its catalog, GE was proposing a passenger version of the E60C before the BM&LP locomotives even entered service. Importing and adapting a European locomotive would require a three-year lead time; GE promised delivery within a year. With few other options, Amtrak turned to GE to adapt the E60C for passenger service.

Amtrak ordered 26 E60s in 1973; 15 on March 26, 1973, and a further 11 on October 12. The total cost of the order was $18.4 million. The initial order was for 15 locomotives with steam generators and 11 with head-end power, but 9 of the first type were switched to using head-end power as Amtrak ramped up acquisition of Amfleet cars. Amtrak anticipated that E60-hauled Amfleet trains could displace both the GG1s and the mechanically-unreliable Metroliners.

The E60s began arriving in November 1974; they were the first locomotives to carry Amtrak's new Phase II livery. Problems soon developed, as the locomotives yawed sideways when accelerating, stressing the rails. The National Transportation Safety Board investigation after a derailment at Elkton, Maryland on February 24, 1975, revealed problems with the truck and bolster design. The Federal Railroad Administration restricted the maximum speed of the E60s to . While Amtrak accepted the locomotives and publicly expressed "confidence" that they would be cleared for operation, it also arranged for a trial of the Swedish-built four-axle Rc4 electric locomotive. The problems with the E60 persisted into 1977, at which point Amtrak developed the specification for a locomotive based on the Rc4 design. In 1977–78 Amtrak ordered the first of 53 EMD AEM-7s, a twin-cab B-B electric locomotive produced by Electro-Motive Division.

As the AEM-7s arrived Amtrak began disposing of its E60s. It sold two E60CHs to the Navajo Mine Railroad in 1982. A grant from the Urban Mass Transportation Administration enabled New Jersey Transit to buy ten of the E60CHs in 1984 for use on the North Jersey Coast Line. Between 1986 and 1988, those E60s that remained with Amtrak were rebuilt, reclassified and renumbered. All E60CPs had their steam generators removed and four of these had HEP fitted. Those with HEP, both the E60CHs and the converted E60CPs, were rebuilt and renumbered as E60MA in the 600 series. The locomotives were regeared for a maximum speed of . When the E60s returned to service, they were used on heavy, long-distance trains, such as the New York–New Orleans ''Crescent'', the New York–Florida ''Silver Service'', and the Washington, D.C.–Montreal '' Montrealer''. They could also be found in push–pull service on the '' Keystone Service'' trains in the late 1980s and on trains in the early 1990s.

New Jersey Transit began buying ABB ALP-44s, an improved version of the EMD AEM-7 from Asea Brown Boveri, in 1990. It would acquire 32 altogether by the end of 1996. The E60 was off the New Jersey Transit roster by 1998. No. 958 was preserved by the United Railroad Historical Society of New Jersey. All Amtrak E60s were retired in 2003, having been replaced mostly by the HHP-8. In April 2004, the Railroad Museum of Pennsylvania acquired No. 603 for preservation.

Ferrocarriles Nacionales de México

The single largest order of E60Cs was by Ferrocarriles Nacionales de México (NdeM), the national railroad of Mexico. NdeM ordered 39 E60C-2 locomotives, built between 1982 and 1983. NdeM intended to use the locomotives on a new railway line between Mexico City and Querétaro. The line operated from 1994 to 1997; many locomotives never ran in revenue service. After privatization in 1997, Transportación Ferroviaria Mexicana (TFM) dismantled the electrification. The locomotives were made available for sale; eight were still owned by GE and, never delivered, stored in Brownsville, Texas. The availability of several dozen lightly used electric locomotives sparked interest from several commuter operators, including Caltrain in the San Francisco Bay Area and GO Transit in Toronto.

TFM traded 22 of the E60C-2s to GE for GE AC4400CW diesel locomotives. Three were sold to Texas Utilities to serve the company's Martin Lake Line, displacing GE E25Bs. They lasted in service until the end of electrified operations in 2011. EMD SD50 diesel locomotives replaced them. The E25Bs, smaller versions of the E60, had been in use since 1976. Another six went to the Black Mesa and Lake Powell, replacing its aging E60Cs. Five went to the Deseret Power Railroad. Texas Utilities discontinued electric operation in January 2011.

Deseret-Western Railway

In addition to the 39 locomotives delivered to NdeM, GE built two E60C-2s for the Deseret-Western Railway. The Deseret-Western, like the Black Mesa and Lake Powell Railroad, is a dedicated line hauling coal between a mine and a power station. The line opened in 1984. The Deseret-Western, now called the Deseret Power Railroad, supplemented its fleet with two ex-NdeM locomotives in the late 1990s, and another three in the 2000s.

Notes

References

*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*

Further reading

*
*
*

External links

NdeM E60C-2 Photo Gallery by Jorge Luna Helú

{{Amtrak rollingstock

Amtrak locomotives
E60
C-C locomotives
11 kV AC locomotives
25 kV AC locomotives
50 kV AC locomotives
Passenger locomotives
Electric locomotives of the United States
Preserved electric locomotives
Standard-gauge locomotives of the United States
Railway locomotives introduced in 1972