revolution per minute

Revolutions per minute (abbreviated rpm, RPM, rev/min, r/min, or r⋅min⁻¹) is a unit of rotational speed (or rotational frequency) for rotating machines.
One revolution per minute is equivalent to hertz.

Standards

ISO 80000-3:2019 defines a physical quantity called ''rotation'' (or ''number of revolutions''), dimensionless, whose instantaneous rate of change is called ''rotational frequency'' (or ''rate of rotation''), with units of reciprocal seconds (s⁻¹).

A related but distinct quantity for describing rotation is ''angular frequency'' (or ''angular speed'', the magnitude of angular velocity), for which the SI unit is the radian per second (rad/s).

Although they have the same dimensions (reciprocal time) and base unit (s⁻¹), the hertz (Hz) and radians per second (rad/s) are special names used to express two different but proportional ISQ quantities: frequency and angular frequency, respectively. The conversions between a frequency and an angular frequency are
: $\omega = 2 \pi f, \quad f = \frac.$

Thus a disc rotating at 60 rpm is said to have an angular speed of 2''π'' rad/s and a rotation frequency of 1 Hz.

The International System of Units (SI) does not recognize rpm as a unit. It defines units of angular frequency and angular velocity as rad s⁻¹, and units of frequency as Hz, equal to s⁻¹.

: $\begin 1~\dfrac &=& \dfrac~\text &=& \dfrac~\text \\ 2\pi~\dfrac &=& 1~\text &=& 60~\text \\ \dfrac~\dfrac &=& \dfrac~\text &=& 1~\text \end$

Examples

* For a wheel, a pump, or a crank shaft, the number of times that it completes one full cycle in one minute is given the unit revolution per minute. A revolution is one complete period of motion, whether this be circular, reciprocating or some other periodic motion.
* On many kinds of disc recording media, the rotational speed of the medium under the read head is a standard given in rpm. Phonograph (gramophone) records, for example, typically rotate steadily at , , 45 rpm or 78 rpm (0.28, 0.55, 0.75, or 1.3, respectively, in Hz).
* Air turbine rotating up to (25 kHz)
* Modern air turbine dental drills can rotate at over (13.3 kHz).
* The second hand of a conventional analog clock rotates at 1 rpm.
* Audio CD players read their discs at a precise, constant rate (4.3218 Mbit/s of raw physical data for 1.4112 Mbit/s (176.4 KB/s) of usable audio data) and thus must vary the disc's rotational speed from 8 Hz (480 rpm) when reading at the innermost edge to 3.5 Hz (210 rpm) at the outer edge.
* DVD players also usually read discs at a constant linear rate. The disc's rotational speed varies from 25.5 Hz (1530 rpm) when reading at the innermost edge, to 10.5 Hz (630 rpm) at the outer edge.
* A washing machine's drum may rotate at 500 rpm to (8 Hz – 46 Hz) during the spin cycles.
* A baseball thrown by a Major League Baseball pitcher can rotate at over (41.7 Hz); faster rotation yields more movement on breaking balls.
* A power-generation turbine ( with a two-pole alternator) rotates at 3000 rpm (50 Hz), 3600 rpm (60 Hz), and over 4000 rpm ( Hz)
* Modern automobile engines are typically operated around – (31 Hz – 48 Hz) when cruising, with a minimum (idle) speed around 750 rpm – 900 rpm (12.5 Hz – 15 Hz), and an upper limit anywhere from 4800 rpm to up to (80 Hz – 158 Hz) for a road car, very rarely reaching up to for certain cars (such as the GMA T.50), or for racing engines such as those in Formula 1 cars (during the season, with the 2.4 L N/A V8 engine configuration; limited to , with the 1.6 L V6 turbo- hybrid engine configuration). The exhaust note of V8, V10, and V12 F1 cars has a much higher pitch than an I4 engine, because each of the cylinders of a four-stroke engine fires once for every two revolutions of the crankshaft. Thus an eight-cylinder engine turning 300 times per second will have an exhaust note of .
* A piston aircraft engine typically rotates at a rate between and (42 Hz – 166 Hz).
* Computer hard drives typically rotate at – (125 Hz – 166 Hz), the most common speeds for the ATA or SATA-based drives in consumer models. High-performance drives (used in fileservers and enthusiast-gaming PCs) rotate at – (160 Hz – 250 Hz), usually with higher-level SATA, SCSI or Fibre Channel interfaces and smaller platters to allow these higher speeds, the reduction in storage capacity and ultimate outer-edge speed paying off in much quicker access time and average transfer speed thanks to the high spin rate. Until recently, lower-end and power-efficient laptop drives could be found with or even spindle speeds (70 Hz or 60 Hz), but these have fallen out of favour due to their lower performance, improvements in energy efficiency in faster models and the takeup of solid-state drives for use in slimline and ultraportable laptops. Similar to CD and DVD media, the amount of data that can be stored or read for each turn of the disc is greater at the outer edge than near the spindle; however, hard drives keep a constant rotational speed so the effective data rate is faster at the edge (conventionally, the "start" of the disc, opposite to a CD or DVD).
* Floppy disc drives typically ran at a constant 300 rpm or occasionally 360 rpm (a relatively slow 5 Hz or 6 Hz) with a constant per-revolution data density, which was simple and inexpensive to implement, though inefficient. Some designs such as those used with older Apple computers (Lisa, early Macintosh, later II's) were more complex and used variable rotational speeds and per-track storage density (at a constant read/record rate) to store more data per disc; for example, between 394 rpm (with 12 sectors per track) and 590 rpm (8 sectors) with Mac's 800 kB double-density drive at a constant 39.4 kB/s (max) – versus 300 rpm, 720 kB and 23 kB/s (max) for double-density drives in other machines.
* A Zippe-type centrifuge for enriching uranium spins at () or faster.
* Gas turbine engines rotate at tens of thousands of rpm. JetCat model aircraft turbines are capable of over () with the fastest reaching ().
* A Flywheel energy storage system works at – (1 kHz – 8.3 kHz) range using a passively magnetic levitated flywheel in a vacuum. The choice of the flywheel material is not the most dense, but the one that pulverises the most safely, at surface speeds about 7 times the speed of sound.
* A typical 80 mm, 30 CFM computer fan will spin at – (43 Hz – 50 Hz) on 12 V DC power.
* A millisecond pulsar can have near (833 Hz).
* A turbocharger can reach (16.6 kHz), while – (1 kHz – 3 kHz) is common.
* A supercharger can spin at speeds between or as high as – (833 Hz – 1666 Hz)
* Molecular microbiology – molecular engines. The rotation rates of bacterial flagella have been measured to be (170 Hz) for ''Salmonella typhimurium'', (270 Hz) for ''Escherichia coli'', and up to () for polar flagellum of '' Vibrio alginolyticus'', allowing the latter organism to move in simulated natural conditions at a maximum speed of 540 mm/h.
* The sample in magic angle spinning, a nuclear magnetic resonance technique, typically rotates between and (5–), with experimental instruments reaching speeds as high as ().

See also

* Constant angular velocity (CAV) – used when referring to the speed of gramophone (phonograph) records
* Constant linear velocity (CLV) – used when referring to the speed of audio CDs
*Radian per second
*Rotational speed
*Compressor map
*Turn (geometry)
* Idle speed
*Overspeed (engine)
*Redline
*Rev limiter
*Tachometer

Notes

References

{{reflist

Units of frequency
Rotation