Hydrogen Explosion

Hydrogen safety covers the safe production, handling and use of hydrogen, particularly hydrogen gas fuel and liquid hydrogen. Hydrogen possesses the NFPA 704's highest rating of four on the flammability scale because it is flammable when mixed even in small amounts with ordinary air. Ignition can occur at a volumetric ratio of hydrogen to air as low as 4% due to the oxygen in the air and the simplicity and chemical properties of the reaction. However, hydrogen has no rating for innate hazard for reactivity or toxicity. The storage and use of hydrogen poses unique challenges due to its ease of leaking as a gaseous fuel, low-energy ignition, wide range of combustible fuel-air mixtures, buoyancy, and its ability to embrittle metals that must be accounted for to ensure safe operation.

Liquid hydrogen poses additional challenges due to its increased density and the extremely low temperatures needed to keep it in liquid form. Moreover, its demand and use in industry—as rocket fuel, alternative energy storage source, coolant for electric generators in power stations, a feedstock in industrial and chemical processes including production of ammonia and methanol, etc.—has continued to increase, which has led to the increased importance of considerations of safety protocols in producing, storing, transferring, and using hydrogen.

Hydrogen has one of the widest explosive/ignition mix range with air of all the gases with few exceptions such as acetylene, silane, and ethylene oxide, and in terms of minimum necessary ignition energy and mixture ratios has extremely low requirements for an explosion to occur. This means that whatever the mix proportion between air and hydrogen, when ignited in an enclosed space a hydrogen leak will most likely lead to an explosion, not a mere flame.

There are many codes and standards regarding hydrogen safety in storage, transport, and use. These range from federal regulations, ANSI/AIAA, NFPA, and ISO standards. The Canadian Hydrogen Safety Program concluded that hydrogen fueling is as safe as, or safer than, compressed natural gas (CNG) fueling,

Prevention

There are a number of items to consider to help design systems and procedures to avoid accidents when dealing with hydrogen, as one of the primary dangers of hydrogen is that it is extremely flammable.

Inerting and purging

Inerting chambers and purging gas lines are important standard safety procedures to take when transferring hydrogen. In order to properly inert or purge, the flammability limits must be taken into account, and hydrogen's are very different from other kinds of gases. At normal atmospheric pressure it is 4% to 75%, based on the volume percent of hydrogen in oxygen it is 4% to 94%, while the limits of the detonation potential of hydrogen in air are 18.3% to 59% by volume. In fact, these flammability limits can often be more stringent than this, as the turbulence during a fire can cause a deflagration which can create detonation. For comparison the deflagration limit of gasoline in air is 1.4–7.6%, and of acetylene in air, 2.5–82%.

Therefore, when equipment is open to air before or after a transfer of hydrogen, there are unique conditions to take into consideration that might have otherwise been safe with transferring other kinds of gases. Incidents have occurred because inerting or purging was not sufficient, or because the introduction of air in the equipment was underestimated (e.g., when adding powders), resulting in an explosion. For this reason, inerting or purging procedures and equipment are often unique to hydrogen, and often the fittings or marking on a hydrogen line should be completely different to ensure that this and other processes are properly followed, as many explosions have happened simply because a hydrogen line was accidentally plugged into a main line or because the hydrogen line was confused with another.

Ignition source management

The minimum ignition energy of hydrogen in air is one of the lowest among known substances at 0.02 mJ, and hydrogen-air mixtures can ignite with 1/10 the effort of igniting gasoline-air mixtures. Because of this, any possible ignition source has to be scrutinized. Any electrical device, bond, or ground should meet applicable hazardous area classification requirement. Any potential sources (like some ventilation system designs) for static electricity build-up should likewise be minimized, e.g. through antistatic devices.

Hot-work procedures must be robust, comprehensive, and well-enforced; and they should purge and ventilate high-areas and sample the atmosphere before work. Ceiling-mounted equipment should likewise meet hazardous area requirements (NFPA 497). Finally, rupture discs should not be used as this has been a common ignition source for multiple explosions and fires. Instead other pressure relief systems such as a relief valve should be used.

Mechanical integrity and reactive chemistry

There are four main chemical properties to account for when dealing with hydrogen that can come into contact with other materials even in normal atmospheric pressures and temperatures:

* The chemistry of hydrogen is very different from traditional chemicals. E.g., with oxidation in ambient environments. And neglecting this unique chemistry has caused issues at some chemical plants. Another aspect to be considered as well is the fact that hydrogen can be generated as a byproduct of a different reaction may have been overlooked, e.g. Zirconium and steam creating a source of hydrogen. This danger can be circumvented somewhat via the use of passive autocatalytic recombiners.
* Another major issue to consider is the chemical compatibility of hydrogen with other common building materials like steel. Because of hydrogen embrittlement, material compatibility with hydrogen is specially considered.
* These considerations can further change because of special reactions at high temperatures.
* The diffusivity of hydrogen is very different from ordinary gases, and therefore gasketing materials have to be chosen carefully.
* The buoyant forces and stresses on mechanical bodies involved are often reversed from standard gases. For example, because of buoyancy, stresses are often pronounced near the top of a large storage tank.

All four of these factors are considered during the initial design of a system using hydrogen, and is typically accomplished by limiting the contact between susceptible metals and hydrogen, either by spacing, electroplating, surface cleaning, material choice, and quality assurance during manufacturing, welding, and installation. Otherwise, hydrogen damage can be managed and detected by specialty monitoring equipment.

Leaks and flame detection systems

Locations of hydrogen sources and piping have to be chosen with care. Since hydrogen is a lighter-than-air gas, it collects under roofs and overhangs (typically referred to as trapping sites), where it forms an explosion hazard. Many individuals are familiar with protecting plants from heavier-than-air vapors, but are unfamiliar with "looking up", and is therefore of particular note. It can also enter pipes and can follow them to their destinations. Because of this, hydrogen pipes should be well-labeled and located above other pipes to prevent this occurrence.

Even with proper design, hydrogen leaks can support combustion at very low flow rates, as low as 4 micrograms/s. To this end, detection is important. Hydrogen sensors or a katharometer allow for rapid detection of hydrogen leaks to ensure that the hydrogen can be vented and the source of the leak tracked down. Around certain pipes or locations special tapes can be added for hydrogen detection purposes. A traditional method is to add a hydrogen odorant with the gas as is common with natural gas. In fuel cell applications these odorants can contaminate the fuel cells, but researchers are investigating other methods that might be used for hydrogen detection: tracers, new odorant technology, advanced sensors, and others.

While hydrogen flames can be hard to see with the naked eye (it can have a so-called "invisible flame"), they show up readily on UV/IR flame detectors. More recently Multi IR detectors have been developed, which have even faster detection on hydrogen-flames. This is quite important in fighting hydrogen fires, as the preferred method of fighting a fire is stopping the source of the leak, as in certain cases (namely, cryogenic hydrogen) dousing the source directly with water may cause icing, which in turn may cause a secondary rupture.

Ventilation and flaring

Aside from flammability concerns, in enclosed spaces, hydrogen can also act as an asphyxiant gas. Therefore, one should make sure to have proper ventilation to deal with both issues should they arise, as it is generally safe to simply vent hydrogen into the atmosphere. However, when placing and designing such ventilation systems, one must keep in mind that hydrogen will tend to accumulate towards the ceilings and peaks of structures, rather than the floor. Many dangers may be mitigated by the fact that hydrogen rapidly rises and often disperses before ignition.

In certain emergency or maintenance situations, hydrogen can also be flared. For example, a safety feature in some hydrogen-powered vehicles is that they can flare the fuel if the tank is on fire, burning out completely with little damage to the vehicle, in contrast to the expected result in a gasoline-fueled vehicle.

Inventory management and facility spacing

Ideally, no fire or explosion will occur, but the facility should be designed so that if accidental ignition occurs, it will minimize additional damage. Minimum separation distances between hydrogen storage units should be considered, together with the pressure of said storage units (cf., NFPA 2 and 55). Explosion venting should be laid out so that other parts of the facility will not be harmed. In certain situations, this translates to a roof that can be safely blown away from the rest of the structure in an explosion.

Cryogenics

Liquid hydrogen has a slightly different chemistry compared to other cryogenic chemicals, as trace accumulated air can easily contaminate liquid hydrogen and form an unstable mixture with detonative capabilities similar to TNT and other highly explosive materials. Because of this, liquid hydrogen requires complex storage technology such as the special thermally insulated containers and requires special handling common to all cryogenic substances. This is similar to, but more severe than liquid oxygen. Even with thermally insulated containers it is difficult to keep such a low temperature, and the hydrogen will gradually leak away. Typically it will evaporate at a rate of 1% per day.

The main danger with cryogenic hydrogen is what is known as BLEVE (boiling liquid expanding vapor explosion). Because hydrogen is gaseous in atmospheric conditions, the rapid phase change together with the detonation energy combine to create a more hazardous situation. A secondary danger is the fact that many materials change from being to ductile to brittle at extremely cold temperatures, allowing new places for leaks to form.

Human factors

Along with traditional job safety training, checklists to help prevent commonly skipped steps (e.g., testing high points in the work area) are often implemented, along with instructions on the situational dangers that come inherent to working with hydrogen.

Incidents

Hydrogen codes and standards

There exist many hydrogen codes and standards for hydrogen fuel cell vehicles, stationary fuel cell applications and portable fuel cell applications. Additional to the codes and standards for hydrogen technology products, there are codes and standards for hydrogen safety, for the safe handling of hydrogen and the storage of hydrogen. What follows is a list of some of the major codes and standards regulating hydrogen:

Guidelines

The current ANSI/AIAA standard for hydrogen safety guidelines is AIAA G-095-2004, Guide to Safety of Hydrogen and Hydrogen Systems. As NASA has been one of the world's largest users of hydrogen, this evolved from NASA's earlier guidelines, NSS 1740.16 (8719.16). These documents cover both the risks posed by hydrogen in its different forms and how to ameliorate them. NASA also references Safety Standard for Hydrogen and Hydrogen Systems and the Sourcebook for Hydrogen Applications.

Another organization responsible for hydrogen safety guidelines is th
Compressed Gas Association (CGA)
which has a number of references of their own covering general hydrogen storage, piping, and venting.

In 2023 CGA launched th
Safe Hydrogen Project
which is a collaborative global effort to develop and distribute safety information for the production, storage, transport, and use of hydrogen.

See also

* Dissolved gas analysis
*Electrical equipment in hazardous areas
*Hydrogen economy
*Metallic hydrogen
*Oxyhydrogen
* Passive autocatalytic recombiner
*Slush hydrogen

References

External links

Hydrogen and Fuel Cell Safety ReportThe International Association for Hydrogen SafetyHigher Educational Programme in Hydrogen Safety EngineeringKnowledge Center for Explosion and Hydrogen Safety

{{DEFAULTSORT:Hydrogen Safety
Hydrogen
Safety
Process safety