gridiron pendulum

A gridiron pendulum was a temperature-compensated clock pendulum invented by British clockmaker John Harrison around 1726. It was used in precision clocks. In ordinary clock pendulums, the pendulum rod expands and contracts with changes in temperature. The period of the pendulum's swing depends on its length, so a pendulum clock's rate varied with changes in ambient temperature, causing inaccurate timekeeping. The gridiron pendulum consists of alternating parallel rods of two metals with different thermal expansion coefficients, such as steel and brass. The rods are connected by a frame in such a way that their different thermal expansions (or contractions) compensate for each other, so that the overall length of the pendulum, and thus its period, stays constant with temperature.

The gridiron pendulum was used during the Industrial Revolution period in pendulum clocks, particularly precision ''regulator clocks'' employed as time standards in factories, laboratories, office buildings, railroad stations and post offices to schedule work and set other clocks. The gridiron became so associated with accurate timekeeping that by the turn of the 20th century many clocks had pendulums with decorative fake gridirons, which had no temperature compensating qualities.

How it works

The gridiron pendulum is constructed so the high thermal expansion (zinc or brass) rods make the pendulum shorter when they expand, while the low expansion steel rods make the pendulum longer. By using the correct ratio of lengths, the greater expansion of the zinc or brass rods exactly compensate for the greater length of the low expansion steel rods, and the pendulum stays the same length with temperature changes.

The simplest form of gridiron pendulum, introduced as an improvement to Harrison's around 1750 by John Smeaton, consists of five rods, 3 of steel and two of zinc. A central steel rod runs up from the bob to the suspension pivot.

At that point a cross-piece (middle bridge) extends from the central rod and connects to two zinc rods, one on each side of the central rod, which reach down to, and are fixed to, the bottom bridge just above the bob. The bottom bridge clears the central rod and connects to two further steel rods which run back up to the top bridge attached to the suspension. As the steel rods expand in heat, the bottom bridge drops relative to the suspension, and the bob drops relative to the middle bridge. However, the middle bridge rises relative to the bottom one because the greater expansion of the zinc rods pushes the middle bridge, and therefore the bob, upward to match the combined drop caused by the expanding steel.

In simple terms, the upward expansion of the zinc counteracts the combined downward expansion of the steel (which has a greater total length). The rod lengths are calculated so that the effective length of the zinc rods multiplied by zinc's thermal expansion coefficient equals the effective length of the steel rods multiplied by iron's expansion coefficient, thereby keeping the pendulum the same length.

Harrison's original pendulum used brass rods (pure zinc not being available then); these required more rods because brass does not expand as much as zinc does. Instead of one high expansion rod on each side, two are needed on each side, requiring a total of 9 rods, five steel and four brass. The exact degree of compensation can be adjusted by having a section of the central rod which is partly brass and partly steel. These overlap (like a sandwich) and are joined by a pin which passes through both metals. A number of holes for the pin are made in both parts and moving the pin up or down the rod changes how much of the combined rod is brass and how much is steel.

In the late 19th century the Dent company developed a tubular version of the zinc gridiron in which the four outer rods were replaced by two concentric tubes which were linked by a tubular nut which could be screwed up and down to alter the degree of compensation.

In the 1730s clockmaker John Ellicott designed a version that only required 3 rods, two brass and one steel (''see drawing''), in which the brass rods as they expanded with increasing temperature pressed against levers which lifted the bob. The Ellicott pendulum did not see much use.

Disadvantages

Scientists in the 1800s found that the gridiron pendulum had disadvantages that made it unsuitable for the highest-precision clocks. The friction of the rods sliding in the holes in the frame caused the rods to adjust to temperature changes in a series of tiny jumps, rather than with a smooth motion. This caused the rate of the pendulum, and therefore the clock, to change suddenly with each jump. Later it was found that zinc is not very stable dimensionally; it is subject to creep. Therefore, another type of temperature-compensated pendulum, the mercury pendulum invented in 1721 by George Graham, was used in the highest-precision clocks.

By 1900, the highest-precision astronomical regulator clocks used pendulum rods of low thermal expansion materials such as invar and fused quartz.

Gallery

File:Standuhr_KGM_1980-91.jpg
File:Akademieuhr4.jpg
File:ML.-_Uhren_(3).JPG
File:Reloj_de_pesas_1970.jpg
File:Uhren_-_M.L._(9).jpg
File:Volodymyr_Ivasyuk_03.jpg
File:Eight_day_regulator_clock,_1860.jpg
File:Paardjesklok.jpg
File:Väggklocka_CO.JPG
File:1815-30_Uhr_in_Form_eines_pendule_oscillante_anagoria.JPG
File:Heimatmuseum_Unterföhring_1.jpg
File:Vienna_-_Vintage_Table_or_Mantel_Clock_-_0575.jpg
File:Wall-mounted_grandfather_clock_(40587721581).jpg
File:Liège,_Grand_Curtius,_collection_Duesberg01.JPG
File:Nels_built_1892_longcase_clock.JPG
File:Beauvais_Cathédrale_Saint-Pierre_Innen_Astronomische_Uhr_7.jpg
File:Besançon_-_Cathédrale_Saint-Jean_de_Besançon_-_001.jpg
File:Ścienny_zegar_wahadłowy_-_2013.05.09.jpg

Mathematical analysis

Temperature error

All substances expand with an increase in temperature $\theta$, so uncompensated pendulum rods get longer with a temperature increase, causing the clock to slow down, and get shorter with a temperature decrease, causing the clock to speed up. The amount depends on the linear coefficient of thermal expansion (CTE) $\alpha$ of the material they are composed of. CTE is usually given in parts per million (ppm) per degree Celsius. If a rod has a length $L$ at some standard temperature $\theta_\text$, the length of the rod as a function of temperature is
:L(\theta) = L + \alpha L(\theta - \theta_\text) = L + \alpha(\theta - \theta_\text)/math>
If $\Delta L = L(\theta) - L$ and $\Delta\theta = \theta - \theta_\text$, the expansion or contraction of a rod of length $L$ with a coefficient of expansion $\alpha$ caused by a temperature change $\Delta\theta$ is
:$\Delta L = \alpha L \Delta\theta$        (1)

The period of oscillation $T$ of the pendulum (the time interval for a right swing and a left swing) is
:$T = 2\pi\sqrt$        (2)
A change in length $\Delta L$ due to a temperature change $\Delta\theta$ will cause a change in the period $\Delta T$. Since the expansion coefficient is so small, the length changes due to temperature are very small, parts per million, so $\Delta T << T$ and the change in period can be approximated to first order as a linear function
:$\Delta T = \Delta L$
:$\qquad = \Big( 2\pi\sqrt\Big)\Delta L = \pi$
Substituting equation (1), the change in the pendulum's period caused by a change in temperature $\Delta\theta$ is
:$\qquad = \pi = \alpha\pi\sqrt\Delta\theta$
:$\Delta T =$

So the fractional change in an uncompensated pendulum's period is equal to one-half the coefficient of expansion times the change in temperature.

Steel has a CTE of 11.5 parts per million per °C so a pendulum with a steel rod will have a thermal error rate of
5.7 parts per million or 0.5 seconds per day per degree Celsius (0.9 seconds per day per degree Fahrenheit). Before 1900 most buildings were unheated, so clocks in temperate climates like Europe and North America would experience a summer/winter temperature variation of around resulting in an error rate of 6.8 seconds per day.

Although this seems like a small error, it should be kept in mind that in the 1700s and 1800s pendulum clocks were primary standards used for exacting tasks like keeping trains on schedule, and that outside big cities there were no time standards, so it was a difficult process to set a clock accurately to the correct time. A transit telescope instrument was required to observe the exact moment when the sun or a star passed overhead, then almanac tables were consulted to determine the time the clock should be set to. So clocks in rural areas typically had to run for long periods between being set. A 6.8 second per day temperature error accumulates a 21 minute error over 6 months.

Wood has a smaller CTE of 4.9 ppm per °C thus a pendulum with a wood rod will have a smaller thermal error of 0.21 sec per day per °C or 2.9 seconds per day for a 14°C seasonal change, so wood pendulum rods were often used in quality domestic clocks. The wood had to be varnished to protect it from the atmosphere as humidity could also cause changes in length.

Compensation

A gridiron pendulum is symmetrical, with two identical linkages of suspension rods, one on each side, suspending the bob from the pivot. Within each suspension chain, the total change in length of the pendulum $L$ is equal to the sum of the changes of the rods that make it up. It is designed so with an increase in temperature the high expansion rods on each side push the pendulum bob up, in the opposite direction to the low expansion rods which push it down, so the net change in length is the difference between these changes
:$\Delta L = \sum \Delta L_\text - \sum \Delta L_\text$
From (1) the change in length $\Delta L$ of a gridiron pendulum with a temperature change $\Delta\theta$ is
:$\Delta L = \sum\alpha_\textL_\text\Delta\theta - \sum\alpha_\textL_\text\Delta\theta$
:$\Delta L = (\alpha_\text\sum L_\text - \alpha_\text\sum L_\text)\Delta\theta$
where $\sum L_\text$ is the sum of the lengths of all the low expansion (steel) rods and $\sum L_\text$ is the sum of the lengths of the high expansion rods in the suspension chain from the bob to the pivot. The condition for zero length change with temperature is
:$\alpha_\text\sum L_\text - \alpha_\text\sum L_\text = 0$

In other words, the ratio of the total rod lengths must be equal to the inverse ratio of the thermal expansion coefficients of the two metals"''The total lengths should be inversely proportional to the coefficients of expansion for the metals used''" Glasgow, David (1885
''Watch and Clock Making''
Cassell and Co., London, p.289

In order to calculate the length of the individual rods, this equation is solved along with equation (2) giving the total length of pendulum needed for the correct period $T$
:$L = \sum L_\text - \sum L_\text = g\big(\big)^2$
Most of the precision pendulum clocks with gridirons used a 'seconds pendulum', in which the period was two seconds. The length of the seconds pendulum was $L =\,$.

In an ordinary uncompensated pendulum, which has most of its mass in the bob, the center of oscillation is near the center of the bob, so it was usually accurate enough to make the length from the pivot to the center of the bob $L =$ 0.9936 m and then correct the clock's period with the adjustment nut. But in a gridiron pendulum, the gridiron constitutes a significant part of the mass of the pendulum. This changes the moment of inertia so the center of oscillation is somewhat higher, above the bob in the gridiron. Therefore the total length $L$ of the pendulum must be somewhat longer to give the correct period. This factor is hard to calculate accurately. Another minor factor is that if the pendulum bob is supported at bottom by a nut on the pendulum rod, as is typical, the rise in center of gravity due to thermal expansion of the bob has to be taken into account. Clockmakers of the 19th century usually used recommended lengths for gridiron rods that had been found by master clockmakers by trial and error.

Five rod gridiron

In the 5 rod gridiron, there is one high expansion rod on each side, of length $L_\text$, flanked by two low expansion rods with lengths $L_\text$ and $L_\text$, one from the pivot to support the bottom of $L_\text$, the other goes from the top of $L_\text$ down to support the bob. So from equation (3) the condition for compensation is
:$=$
Since to fit in the frame the high expansion rod must be equal to or shorter than each of the low expansion rods $L_\text \ge L_\text$ and $L_\text \ge L_\text$ the geometrical condition for construction of the gridiron is
:$L_\text + L_\text \ge 2L_\text$
Therefore the 5 rod gridiron can only be made with metals whose expansion coefficients have a ratio greater than or equal to two
:$= \ge 2$
Zinc has a CTE of $\alpha$ = 26.2 ppm per °C, versus the steel value of 11.5, so the ratio of $\alpha_\text/\alpha_\text$ = 2.28. Thus the zinc/steel combination can be used in 5 rod pendulums.

The compensation condition for a zinc/steel gridiron is
:$= 2.28$

Nine rod gridiron

To allow the use of metals with a lower ratio of expansion coefficients, such as brass and steel, a greater proportion of the suspension length must be the high expansion metal, so a construction with more high expansion rods must be used. In the 9 rod gridiron, there are two high expansion rods on each side, of length $L_\text$ and $L_\text$, flanked by three low expansion rods with lengths $L_\text$, $L_\text$ and $L_\text$. So from equation (3) the condition for compensation is
:$=$
Since to fit in the frame each of the two high expansion rods must be as short as or shorter than each of the high expansion rods, the geometrical condition for construction is
:$L_\text + L_\text + L_\text \ge (L_\text + L_\text)$
Therefore the 9 rod gridiron can be made with metals with a ratio of thermal expansion coefficients exceeding 1.5.
:$= \ge 1.5$
Brass has a CTE of around $\alpha$ = 19.3 ppm per °C, giving a ratio of $\alpha_\text/\alpha_\text$ = 1.68. So while brass/steel cannot be used in 5 rod gridirons, it can be used in the 9 rod version.
So the compensation condition for a brass/steel gridiron using brass with the above CTE is
:$= 1.68$

Definition of variables

References

Further reading

*
*
*{{cite journal
, last = Short
, first = James
, title = A letter concerning the inventor of the contrivance in a pendulum of a clock to prevent the irregularities of its motion by heat or cold
, journal = Philosophical Transactions of the Royal Society
, volume = 47
, issue = LXXXVIII
, pages = 517–525
, publisher = Royal Society
, location = London
, date = 1753
, language =
, url = https://archive.org/details/in.ernet.dli.2015.26414/page/n617/mode/2up
, jstor =
, issn =
, doi =
, id =
, mr =
, zbl =
, jfm =
, access-date = 9 July 2024

Pendulums
Timekeeping components