Gasoline-equivalent Gallon

Gasoline gallon equivalent (GGE) or gasoline-equivalent gallon (GEG) is the amount of an alternative fuel it takes to equal the energy content of one liquid gallon of gasoline. GGE allows consumers to compare the energy content of competing fuels against a commonly known fuel, namely gasoline.

It is difficult to compare the cost of gasoline with other fuels if they are sold in different units and physical forms. GGE attempts to solve this. One GGE of CNG and one GGE of electricity have exactly the same energy content as one gallon of gasoline. In this way, GGE provides a direct comparison of gasoline with alternative fuels, including those sold as a gas (natural gas, propane, hydrogen) and as metered electricity.

Definition

In 1994, the US National Institute of Standards and Technology (NIST) defined "gasoline gallon equivalent (GGE) s5.660 pounds of natural gas." Compressed natural gas (CNG), for example, is a gas rather than a liquid. It can be measured by its volume in standard cubic feet (ft³) at atmospheric conditions, by its weight in pounds (lb), or by its energy content in joules (J), British thermal units (BTU), or kilowatt-hours (kW·h). CNG sold at filling stations in the US is priced in dollars per GGE.

Using GGE as a measure to compare the stored energy of various fuels for use in an internal combustion engine is only one input for consumers, who typically are interested in the annual cost of driving a vehicle, which requires considering the amount of useful work that can be extracted from a given fuel. This is measured by the car's overall efficiency. In the context of GGE, a real world measure of overall efficiency is the fuel economy or fuel consumption advertised by motor vehicle manufacturers.

Efficiency and consumption

To start, only a fraction of the stored energy of a given fuel (measured in BTU or kW-hr) can be converted to useful work by the vehicle's engine. The measure of this is engine efficiency, often called thermal efficiency in the case of internal combustion engines. A diesel cycle engine can be as much as 40% to 50% efficient at converting fuel into work, where a typical automotive gasoline engine's efficiency is about 25% to 30%.

In general, an engine is designed to run on a single fuel source and substituting one fuel for another may affect the thermal efficiency. Each fuel–engine combination requires adjusting the mix of air and fuel. This can be a manual adjustment using tools and test instruments or done automatically in computer-controlled fuel injected and multi-fuel vehicles. Forced induction for an internal combustion engine using supercharger or turbocharger may also affect the optimum fuel–air mix and thermal efficiency.

The overall efficiency of converting a unit of fuel to useful work (rotation of the driving wheels) includes consideration of thermal efficiency along with dynamic losses that are inherent and specific to the design of a given vehicle. Thermal efficiency is affected by both friction and heat losses; for internal combustion engines, some of the stored energy is lost as heat through the exhaust or cooling system. In addition, friction inside the engine happens along the cylinder walls, crankshaft rod bearings and main bearings, camshaft bearings, drive chains or gears, plus other miscellaneous and minor bearing surfaces. Other dynamic losses can be caused by friction outside the motor/engine, including loads from the generator / alternator, power steering pump, A/C compressor, transmission, transfer case (if four-wheel-drive), differential(s) and universal joints, plus rolling resistance of the pneumatic tires. The vehicle's external styling affects its aerodynamic drag, which is another dynamic loss that must be considered for overall efficiency.

In battery or electric vehicles, calculating the vehicle's overall efficiency of useful work begins with the charge–discharge rate of the battery pack, generally 80% to 90%. Next is the conversion of stored energy to distance traveled under power. Generally speaking, an electrical motor is far more efficient than an internal combustion engine at converting the stored potential energy into useful work; in an electric vehicle, traction motor efficiency can approach 90%, as there is minimal waste heat coming off the motor parts, and zero heat cast off by the coolant radiator and out of the exhaust. An electric motor typically has internal friction only at the main axle bearings. Additional losses will affect the overall efficiency, similar to a conventional internal combustion car, including rolling resistance, aerodynamic drag, accessory power, climate control, and drivetrain losses. See table below translating retail electricity costs for a GGE in BTU.

Overall efficiency is measured and reported, typically by government testing, through operating the vehicle in a standardized driving cycle designed to replicate typical use, while providing a consistent basis for comparison between vehicles. Cars sold in the United States are advertised by their measured overall efficiency (fuel economy) in miles per gallon (mpg). The MPG of a given vehicle starts with the thermal efficiency of the fuel and engine, less all of the above elements of friction. The fuel consumption is an equivalent measure for cars sold outside the United States, typically measured in litres per 100 km traveled; in general, the fuel consumption and miles per gallon would be reciprocals with appropriate conversion factors, but because different countries use different driving cycles to measure fuel consumption, fuel economy and fuel consumption are not always directly comparable.

Miles per gallon of gasoline equivalent (MPGe)

The MPGe metric was introduced in November 2010 by EPA in the Monroney label of the Nissan Leaf electric car and the Chevrolet Volt plug-in hybrid. The ratings are based on EPA's formula, in which 33.7 kilowatt hours of electricity is equivalent to one gallon of gasoline (giving a heating value of ), and the energy consumption of each vehicle during EPA's five standard drive cycle tests simulating varying driving conditions. All new cars and light-duty trucks sold in the U.S. are required to have this label showing the EPA's estimate of fuel economy of the vehicle.

Gasoline gallon equivalent tables

Rates per kWh for residential electricity in the USA range from $0.0728 (Idaho) to $0.166 (Alaska),
$0.22 (San Diego Tier 1, while Tier 2 is $.40) and $0.2783 (Hawaii).

Specific fuels

Compressed natural gas

One GGE of natural gas is at standard conditions. This volume of natural gas has the same energy content as one US gallon of gasoline (based on lower heating values: of natural gas and for gasoline).

One GGE of CNG pressurized at is . This volume of CNG at 2,400 psi has the same energy content as one US gallon of gasoline (based on lower heating values: of CNG and of gasoline. Using Boyle's law, the equivalent GGE at is .

The National Conference of Weights & Measurements (NCWM) has developed a standard unit of measurement for compressed natural gas, defined in the NIST Handbook 44 Appendix D as follows:
"1 Gasoline Sgallon equivalent (GGE) means 2.567 kg (5.660 lb) of natural gas."

When consumers refuel their CNG vehicles in the US, the CNG is usually measured and sold in GGE units. This is fairly helpful as a comparison to gallons of gasoline.

Ethanol and blended fuels (E85)

of ethanol has the same energy content as of gasoline.

The energy content of ethanol is , compared to for gasoline. (see chart above)

A flex-fuel vehicle will experience about 76% of the fuel mileage MPG when using E85 (85% ethanol) products as compared to 100% gasoline. Simple calculations of the BTU values of the ethanol and the gasoline indicate the reduced heat values available to the internal combustion engine. Pure ethanol provides 2/3 of the heat value available in pure gasoline.

In the most common calculation, that is, the BTU value of pure gasoline vs gasoline with 10% ethanol, the latter has just over 96% BTU value of pure gasoline. Gasoline BTU varies relating to the Reid vapor pressure (causing easier vaporization in winter blends containing ethanol (ethanol is difficult to start a vehicle on when it is cold out) and anti-knock additives. Such additives offer a reduction in BTU value.

See also

* Engine efficiency
* Thermal efficiency
* Potential energy
* Work (thermodynamics)
* Work (physics)
* Diesel cycle engines
* Efficiency
* Friction
* Kilowatt hour

References

{{reflist, 30em

Units of energy
Equivalent units