Atjeh-class cruiser

The ''Atjeh'' class was a class of unprotected cruisers of the Royal Netherlands Navy. The class comprised ''Atjeh'', ''Tromp'', ''Koningin Emma der Nederlanden'', ''De Ruyter'', ''Van Speyk'' and ''Johan Willem Friso''.

Context

Replacing steam corvettes with unprotected cruisers

In the 1860s the Netherlands had given priority to building an armored fleet for coastal defense in Europe. Meanwhile, the Dutch East Indies were primarily defended by the steam corvettes called screw steamships first class (s, ). In late 1870 the minister for the navy ordered the first ship meant to replace these, the ironclad . Somewhat later the government decided to replace part of the screw steamships first class with unprotected cruisers (), even though these would also be called screw steamships first class. Later, the armored part would be supplemented by the ironclad , which would be sent to the Indies in 1876. A third armored ship was planned, but postponed 'in order to first gain more experience in the use of armored ships in the tropics'.

There were two very different perspectives on the ''Atjeh'' class. In December 1882 the minister of the navy dismissed the term 'cruiser' for the ''Atjeh'' class, and stated that he was replacing the old screw corvettes. Furthermore, that the design fit the requirements for the defense of the Dutch East Indies. The well known columnist Nautilus had a very different view. He stated that the ''Atjeh'' class was only suitable for cruiser tasks, not for defending the colonies. As a cruiser he thought that it might be a good design, but rather costly.

Design

The first unprotected cruiser design

The first requirements for the ship were determined by Minister for the Navy, Taalman Kip, who had been appointed in May 1874. These called for a ship of no more than 200 men, costing less than 1.5 million guilders. It would be armed with one central 23 cm Armstrong RML, two 18 cm Armstrong RML (fore and aft) and four 12 cm breechloaders. The machines could not be compound, and cruising speed should be , with a trial speed of . The proposed design was a ship long between perpendiculars, had a beam, a draft, and displacement.

This ship would have been considerably longer and narrower, and somewhat bigger than the preceding ''Zilveren Kruis''-class corvettes. The result would have been a screw corvette with a sloop-like armament. With considerably higher speed and better armament, it might have stood up to foreign designs. However, while judging this design, it was noted that the boilers were too high above the normal load line. This would make the ship extremely vulnerable, because it primarily depended on its engines for propulsion. Therefore a new requirement was added, demanding that the steam engines and boilers should be below the empty load line, and be protected by the coal bunkers.

The final design

The requirement to place the steam engines of the new unprotected cruisers below the load line necessitated the design of a substantially bigger ship. Meanwhile, the bridge, fore- and aft castle of the original design were replaced by a spar deck. This new design was approved on 18 December 1874. All this made the ''Atjeh'' class longer, but still narrower than the ''Zilveren Kruis'' class it was to replace. Such a narrow hull was not desirable, but a wider hull would have required much heavier engines, making the ship too expensive in total.

Two subclasses

At least two subclasses can be discerned in the ''Atjeh'' class. The first three ships had traditional steam engines, later ships had compound engines, which led to a substantial difference in power and range. The second group was also somewhat larger in overall length and draft.

The beam was largest for ''Johan Willem Friso''. She was planned to be different from the second group (''De Ruyter'', ''Van Speyk'', ''Doggersbank'' and ''Kortenaer''), but when the last two were burnt, she had to re-use the engines of ''Doggersbank'' (which had not been installed yet), and the stern of ''Kortenaer''. This made her almost equal to ''De Ruyter'' and ''Van Speyk''. Nevertheless, her depth of hold was also significantly larger than that of the other two.

Dimensions

According to the final design, the ships of the class were long between perpendiculars and overall. Their beam was , depth of hold , and maximum draft was fore and aft. Displacement would be . However, displacement depends on load. Normally empty and fully loaded displacement differ significantly. With the ''Atjeh'' displacement was further increased by adding extra guns later.

The ships would be made of iron, covered with wood and zinc. The third ship of the class, ''Koningin Emma'' (ex-''De Ruyter''), would use steel for that part of the hull which was above the load line, and also in some other parts of the hull. This would save weight. As mentioned, under water, the hull was iron covered with teak and then zinc. This gave cathodic protection, making that the zinc corroded instead of the iron, and the zinc caught the stuff that grew on the hull. The Iron and wood were connected by Haij's Marine Composition. On ''Atjeh'' this connection was made without closing the seams. On ''Tromp'', these seems were closed, and contact nails were hammered through the wood to make contact with the iron hull, so the galvanic effect was increased. The last ship, ''Johan Willem Friso'', would use copper on the outside, instead of zinc.

Propulsion

The steam engines of the first three ships were reciprocating engines. The specifications were made by the inspectors of the national steam service, F.H.P. van Alphen and F.W. Hudig. Next Koninklijke Fabriek van Stoom- en andere Werktuigen and Fijenoord together made a design for the engines. The steam engines for ''Atjeh'' were built by Koninklijke Fabriek van Stoom- en andere Werktuigen. Those for ''Tromp'' were built by Fijenoord. The steam engines for ''Koningin Emma'' were built by Koninklijke Fabriek.

These reciprocating engines had two cylinders of diameter. Stroke length was . There were four boilers, which were fired at both ends. At each boiler end, there were three fires. The engines were rated at and produced a top speed of . On her trials, ''Atjeh'' made the required speed by steaming . The engine had and a modest coal consumption.

The fourth and later ships got compound steam engines. The steam engines of ''De Ruyter'' were built by Fijenoord, according to 'Sell's' system. This enabled the use of the machine as a regular steam engine, with lower pressure. This was useful if the boilers were weak, or in case the ship was fighting batteries.

The first three ships had a machine to lift the propeller. With some provisions this enabled the crew to clean the propeller without visiting a shipyard.

In 1878 ''Atjeh'' made a trial cruise in the North Sea. With a wind of 5-6 beaufort, she made under sail. This was deemed very good for a steamer with auxiliary sailing capacity.

Armament

When ''Atjeh'' was laid down, she was reported to get an armament of one central 23 cm RML, four 15 cm Krupp breechloaders (two fore and two aft), and some 12 cm breechloaders in the sides. The two 18 cm RMLs of the first design had been replaced, but the 23 cm RML was still part of the plan at that time. In October 1875 another change in plan determined the armament of ''Atjeh'' and ''Tromp'' to the all breechloaders configuration (six 17 cm guns) with which they were launched.

When she was launched, the armament of ''Atjeh'' had been determined at six 17 cm Krupp breechloaders. These were all placed on the gun deck. One near the bow, one near the stern, and four more to the center of the ship. Large gun ports in bow and stern would enable these guns to fire along the line of the keel. The broadside would be four 17 cm guns. One hoped to still add four 12 cm K.A. breechloaders, and after launch this indeed proved to be possible.

Therefore, the first ships were finished with six guns and four single guns. The fourth ship, ''De Ruyter'', was planned to have eight 12 cm breechloaders from the start.

Construction

All eight ships were laid down at the ''Rijkswerf'' in Amsterdam and launched between 1876 and 1886. Two were never completed and destroyed in a yard fire in 1883.

Notes

References

* Staatsbegrooting voor het dienstjaa
1897
*
*
*
*
*
*
*
*

External links

{{DEFAULTSORT:Atjeh-class cruiser

19th-century naval ships of the Netherlands
Cruiser classes