|
Plymouth Fury III
The Plymouth Fury is a model of automobile that was produced by Plymouth from 1955 until 1989. It was introduced for the 1956 model year as a sub-series of the Plymouth Belvedere, becoming a separate series one level above the contemporary Belvedere for 1959. The Fury was a full-size car from 1959 until 1961, then a mid-size car from 1962 until 1964, again, a full-size car from 1965 through 1974, and again, a mid-size car from 1975 through 1978. From 1975 until 1977, the Fury was sold alongside the full-size Plymouth Gran Fury. In 1978, the B-body Fury was the largest Plymouth, and by 1979, there was no large Plymouth. This product gap was filled in 1980 with the R-body Gran Fury, followed by the M-body Fury in 1982. Production of the last V8, RWD Plymouth Fury ended at the Kenosha Main assembly plant in Kenosha, WI, on December 23, 1988. Unlike its sibling brand, Dodge, Plymouth would not live to see the resurgence of the large, V8/RWD sedan. Early history (1956–1958) The ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Plymouth (automobile)
Plymouth was a brand of automobiles produced by Chrysler, Chrysler Corporation and its successor Mercedes-Benz Group, DaimlerChrysler. The brand was launched in 1928 to compete in what was then described as the "low-priced" market segment that was dominated by Chevrolet and Ford Motor Company, Ford. It became a high-volume seller for the automaker until the late 1990s. Plymouth cars were marketed primarily in the United States. The brand was withdrawn from the marketplace in 2001. The Plymouth models that were produced up until then were either discontinued or rebranded as Chrysler or Dodge. History Origins The Plymouth automobile was introduced at Madison Square Garden (1925), Madison Square Garden on July 7, 1928. It was Chrysler Corporation's first entry in the low-priced field previously dominated by Chevrolet and Ford. Plymouths were initially priced higher than the competition, but offered standard features such as internal expanding hydraulic brakes that Ford and Chevr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Canada
Canada is a country in North America. Its Provinces and territories of Canada, ten provinces and three territories extend from the Atlantic Ocean to the Pacific Ocean and northward into the Arctic Ocean, making it the world's List of countries and dependencies by area, second-largest country by total area, with the List of countries by length of coastline, world's longest coastline. Its Canada–United States border, border with the United States is the world's longest international land border. The country is characterized by a wide range of both Temperature in Canada, meteorologic and Geography of Canada, geological regions. With Population of Canada, a population of over 41million people, it has widely varying population densities, with the majority residing in List of the largest population centres in Canada, urban areas and large areas of the country being sparsely populated. Canada's capital is Ottawa and List of census metropolitan areas and agglomerations in Canada, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Electronic Fuel-injection
Fuel injection is the introduction of fuel in an internal combustion engine, most commonly automotive engines, by the means of a fuel injector. This article focuses on fuel injection in reciprocating piston and Wankel rotary engines. All compression-ignition engines (e.g. diesel engines), and many spark-ignition engines (i.e. petrol (gasoline) engines, such as Otto or Wankel), use fuel injection of one kind or another. Mass-produced diesel engines for passenger cars (such as the Mercedes-Benz OM 138) became available in the late 1930s and early 1940s, being the first fuel-injected engines for passenger car use. In passenger car petrol engines, fuel injection was introduced in the early 1950s and gradually gained prevalence until it had largely replaced carburetors by the early 1990s. The primary difference between carburetion and fuel injection is that fuel injection atomizes the fuel through a small nozzle under high pressure, while carburetion relies on suction created b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Bendix Corporation
Bendix Corporation is an American manufacturing and engineering company founded in 1924 and subsidiary of Knorr-Bremse since 2002. During various times in its existence, Bendix made automotive brake shoes and systems, vacuum tubes, aircraft brakes, aeronautical hydraulics and electric power systems, avionics, aircraft and automobile fuel control systems, radios, televisions and computers. A line of home clothes washing machines in the mid-20th century were marketed as Bendix, though those were produced by a partner company that licensed its name. As of 2025, the company focuses on the trucking and automotive industries. History Early history Founder and inventor Vincent Bendix filed for a patent for the Bendix drive on May 2, 1914. The drive engages the starter motor with an internal combustion engine and is still used on most automobiles today. Bendix initially began his new corporation in a hotel room in Chicago in 1914 with an agreement with the struggling bicycle b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Chrysler B Engine
The Chrysler B and RB engines are a series of V8 engine#Size, layout, and classification, big-block V8 gasoline engines introduced in 1958 to replace the Chrysler Hemi engine#First, Chrysler FirePower (first generation Hemi) engines. The B and RB engines are often referred to as "wedge" engines because they use wedge-shaped combustion chambers; this differentiates them from Chrysler's Chrysler Hemi engine#426, 426 Hemi big block engines that are typically referred to as "Hemi" or "426 Hemi" due to their hemispherical shaped combustion chambers. The corporation had been seeking a smaller and lighter replacement for its FirePower engines, in part because new styling dictates meant moving the engine forward in the chassis which negatively affected weight distribution. Design Design features of the B and RB engines include 17 capscrews per cylinder head, a cylinder block that extends below the crankshaft centerline, an intake manifold not exposed to crankcase oil on the underside, st ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Big Block V8
A V8 engine is an eight-cylinder piston engine in which two banks of four cylinders share a common crankshaft and are arranged in a V configuration. Origins The first known V8 was the Antoinette, designed by Léon Levavasseur, and built in 1904 by the French Antoinette company for use in speedboat racing, cars, and later, airplanes. Also in 1904, V8 engines began small-scale production by Renault and Buchet for use in race cars. Design V-angle Most engines use a V-angle (the angle between the two banks of cylinders) of 90 degrees. This angle results in good engine balance, which results in low vibrations. However, the downside is the greater width of the engine compared to those that use a smaller V-angle. V8 engines with a 60-degree V-angle were used in the 1996–1999 Ford Taurus SHO, the 2005–2011 Volvo XC90, and the 2006–2009 Volvo S80. The Ford engine used a 60-degree V-angle because it was based on a V6 engine with a 60-degree V-angle. Both th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Torsion Bar Suspension
A torsion bar suspension, also known as a torsion spring suspension, is any vehicle suspension that uses a torsion bar as its main weight-bearing spring. One end of a long metal bar is attached firmly to the vehicle chassis; the opposite end terminates in a lever, the torsion key, mounted perpendicular to the bar, that is attached to a suspension arm, a spindle, or the axle. Vertical motion of the wheel causes the bar to twist around its axis and is resisted by the bar's torsion resistance. The effective spring rate of the bar is determined by its length, cross section, shape, material, and manufacturing process. Usage Torsion bar suspensions are used on combat vehicles and tanks like the T-72, Leopard 1, Leopard 2, M26 Pershing, M18 Hellcat, M46/M47/M48 Patton, M60 and the M1 Abrams (many tanks from World War II used this suspension), and on modern trucks and SUVs from Ford, Chrysler, GM, Mitsubishi, Mazda, Nissan, Isuzu, LuAZ, and Toyota. Class 8 truck manufacture ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Dodge Coronet
The Dodge Coronet is an automobile that was marketed by Dodge in seven generations, and shared nameplates with the same bodyshell with varying levels of equipment installed. Introduced as a full-size car in 1949, it was the division's highest Trim levels, trim line and moved to the lowest level starting in 1955 through 1959. The name was reintroduced on Mid-size car, intermediate-sized models from the 1965 until 1976 model years. Muscle car versions were available starting in 1965 with the 383 and 426 wedge cu in (7.0 L) Chrysler Chrysler RB engine, RB engine, followed in 1966 by the powerful 426 cu in (7.0 L) Chrysler Hemi engine#Second generation: 426, Chrysler Hemi. Other performance models included the "Superbee", and featured, the 383 cu in (6.3 L) Magnum, among other engine options. The nameplate "wikt:coronet, coronet" is a type of crown worn by royalty. In the 1980s, the Coronet was used on Dodge models marketed in Colombia. __TOC__ First generation (1949–1952) The D ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Chrysler A Engine
The Chrysler A engine is an OHV small-block V8 gasoline engine built by Chrysler from 1956 until 1967. It featured polyspherical combustion chambers, and was offered in displacements from to , and in various high-power configurations. It began to be replaced by the wedge-head LA engine in 1964, and is not related to the hemispherical-head Hemi engine of the 1950s or 1960s. The A engine was released in 1956, and was used exclusively in Plymouths until 1958 and in Chryslers and Dodges from 1959 on. The DeSoto and Dodge 270/315/325 poly used similar head architecture but was not related to the Plymouth A Engine, using its own heads and the same bottom end as the Dodge and Desoto Red Ram Hemi. The A engine cylinder bore center distance is , larger than the earlier Dodge-based poly engines. The A engine formed the design basis of the Chrysler LA engine, evidenced in the many parts that interchange between the two engine families. Plymouth 277 The 277 "Hy-Fire" was the first A- ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Carburetor
A carburetor (also spelled carburettor or carburetter) is a device used by a gasoline internal combustion engine to control and mix air and fuel entering the engine. The primary method of adding fuel to the intake air is through the Venturi effect or Bernoulli's principle or with a Pitot tube in the main metering circuit, though various other components are also used to provide extra fuel or air in specific circumstances. Since the 1990s, carburetors have been largely replaced by fuel injection for cars and trucks, but carburetors are still used by some small engines (e.g. lawnmowers, generators, and concrete mixers) and motorcycles. In addition, they are still widely used on piston-engine–driven aircraft. Diesel engines have always used fuel injection instead of carburetors, as the compression-based combustion of diesel requires the greater precision and pressure of fuel injection. Etymology The term ''carburetor'' is derived from the verb ''carburet'', which means "to ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Anodising
Anodizing is an electrolytic passivation process used to increase the thickness of the natural oxide layer on the surface of metal parts. The process is called ''anodizing'' because the part to be treated forms the anode electrode of an electrolytic cell. Anodizing increases resistance to corrosion and wear, and provides better adhesion for paint primers and glues than bare metal does. Anodic films can also be used for several cosmetic effects, either with thick porous coatings that can absorb dyes or with thin transparent coatings that add reflected light wave interference effects. Anodizing is also used to prevent galling of threaded components and to make dielectric films for electrolytic capacitors. Anodic films are most commonly applied to protect aluminium alloys, although processes also exist for titanium, zinc, magnesium, niobium, zirconium, hafnium, and tantalum. Iron or carbon steel metal exfoliates when oxidized under neutral or alkaline micro-electrolytic conditio ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Hardtop
A hardtop is a rigid form of automobile roof, typically metal, and integral to the vehicle's design, strength, and style. The term typically applies to a pillarless hardtop, a car body style without a B-pillar. The term "pillared hardtop" was used in the 1970s to refer to cars that had a B-pillar but had frameless door glass like a pillarless hardtop. In limited cases, a hardtop roof can be detachable (often designed to store in the trunk), or retractable within the vehicle itself. Pillarless hardtop The pillarless hardtop (abbreviated as "hardtop") is a post-World War II car body designed with no center or B-pillar or glass frames. If window glass frames are present, they are designed to retract with the window when lowered. This creates an impression of uninterrupted glass along the side of the car. Even the smaller automakers like Packard introduced two-door hardtops in 1952 "as a response to America's newly discovered fondness for sportier looking cars that re ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
