|
I-beam
An I-beam is any of various structural members with an - (serif capital letter 'I') or H-shaped cross section (geometry), cross-section. Technical terms for similar items include H-beam, I-profile, universal column (UC), w-beam (for "wide flange"), universal beam (UB), rolled steel joist (RSJ), or double-T (especially in Polish language, Polish, Bulgarian language, Bulgarian, Spanish language, Spanish, Italian language, Italian, and German language, German). I-beams are typically made of structural steel and serve a wide variety of construction uses. The horizontal elements of the are called flanges, and the vertical element is known as the "web". The web resists shear forces, while the flanges resist most of the bending moment experienced by the beam. The Euler–Bernoulli beam equation shows that the -shaped section is a very efficient form for carrying both bending and shearing (physics), shear loads in the plane of the web. On the other hand, the cross-section has a reduced ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Forges De La Providence
Forges de la Providence () was a Belgian steel producing company based in the Hainaut region around Charleroi. Founded as ''Société Anonyme des laminoirs, forges, fonderies et usines de la Providence'' the company had three steel production sites at Marchienne-au-Pont in Belgium, and Réhon and Hautmont in France. The company was independent until 1966 when it became part of the Cockerill-Ougrée, briefly being absorbed into '' Thy-Marcinelle et Monceau'' before becoming part of Cockerill-Sambre. In the 1980s the French steel plants closed, the Belgian plant continued to operate until 2008, becoming part of the Duferco group as Carsid at the beginning of the 21st century. Coke and blast furnace production CARSID plant closed in 2008 due to an economic downturn, and did not restart - the plant was closed in 2012. Company history In 1836 the Englishman Thomas Bonehill built puddling furnaces for the Puissant and Licot de Nîmes families; in 1838 the company ''Société Anonym ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rivet
A rivet is a permanent mechanical fastener. Before being installed, a rivet consists of a smooth cylinder (geometry), cylindrical shaft with a head on one end. The end opposite the head is called the ''tail''. On installation, the deformed end is called the ''shop head'' or buck-tail. Because there is effectively a head on each end of an installed rivet, it can support Tension (physics), tension loads. However, it is much more capable of supporting Shear force, shear loads (loads perpendicular to the axis of the shaft). Fastenings used in traditional wooden boat building, such as copper nails and clinch bolts, work on the same principle as the rivet but were in use long before the term ''rivet'' was introduced and, where they are remembered, are usually classified among nails and bolts respectively. History Solid rivets are one of the oldest and most reliable types of fasteners, having been found in archeology, archaeological findings dating back to the Bronze Age. Rivet ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Bolted Joint
A bolted joint is one of the most common elements in construction and machine design. It consists of a male threaded fastener (e. g., a Bolt (fastener), bolt) that captures and joins other parts, secured with a matching female screw thread. There are two main types of bolted joint designs: Tension (physics), tension joints and Shear stress, shear joints. The selection of the components in a threaded joint is a complex process. Careful consideration is given to many factors such as temperature, corrosion, vibration, fatigue, and initial preload.Barrett, R. T. (1990). Fastener design manual' (No. NAS 1.61: 1228). Joint types Tension joint There are two types of tension joint: non-preloaded and preloaded. Non-preloaded tension joint These joints are not tightened to a precise preload, and the tension is mainly used to keep parts together without generating a high clamping force. An applied tensile load may cause separation of the joint. This type of joint should not be used w ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Welding
Welding is a fabrication (metal), fabrication process that joins materials, usually metals or thermoplastics, primarily by using high temperature to melting, melt the parts together and allow them to cool, causing Fusion welding, fusion. Common alternative methods include solvent welding (of thermoplastics) using chemicals to melt materials being bonded without heat, and #Solid-state welding, solid-state welding processes which bond without melting, such as pressure, cold welding, and diffusion bonding. Metal welding is distinct from lower temperature bonding techniques such as brazing and soldering, which do not melt the base metal (parent metal) and instead require flowing a filler metal to solidify their bonds. In addition to melting the base metal in welding, a filler material is typically added to the joint to form a pool of molten material (the weld pool) that cools to form a joint that can be stronger than the base material. Welding also requires a form of shield to ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Plate Girder
A plate girder bridge is a bridge supported by two or more plate girders. Overview In a plate girder bridge, the plate girders are typically I-beams made up from separate structural steel plates (rather than rolled as a single cross-section), which are welded or, in older bridges, bolted or riveted together to form the vertical web and horizontal flanges of the beam. In some cases, the plate girders may be formed in a Z-shape rather than I-shape. The first tubular wrought iron plate girder bridge was built in 1846-47 by James Millholland for the Baltimore and Ohio Railroad. Plate girder bridges are suitable for short to medium spans and may support railroads, highways, or other traffic. Plate girders are usually prefabricated and the length limit is frequently set by the mode of transportation used to move the girder from the bridge shop to the bridge site. Generally, the depth of the girder is no less than the span, and for a given load bearing capacity, a depth of arou ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Extrusion
Extrusion is a process used to create objects of a fixed cross section (geometry), cross-sectional profile by pushing material through a Die (manufacturing), die of the desired cross-section. Its two main advantages over other manufacturing processes are its ability to create very complex cross-sections; and to work materials that are brittle, because the material encounters only compressive stress, compressive and shear stress, shear stresses. It also creates excellent surface finish and gives considerable freedom of form in the design process. Drawing (manufacturing), Drawing is a similar process, using the tensile strength of the material to pull it through the die. It limits the amount of change that can be performed in one step, so it is limited to simpler shapes, and multiple stages are usually needed. Drawing is the main way to produce wire. Metal Bar stock, bars and tube (fluid conveyance), tubes are also often drawn. Extrusion may be continuous (theoretically producin ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cold Rolling
In metalworking, rolling is a metal forming process in which metal stock is passed through one or more pairs of rolls to reduce the thickness, to make the thickness uniform, and/or to impart a desired mechanical property. The concept is similar to the rolling of dough. Rolling is classified according to the temperature of the metal rolled. If the temperature of the metal is above its recrystallization temperature, then the process is known as hot rolling. If the temperature of the metal is below its recrystallization temperature, the process is known as cold rolling. In terms of usage, hot rolling processes more tonnage than any other manufacturing process, and cold rolling processes the most tonnage out of all cold working processes... Roll stands holding pairs of rolls are grouped together into rolling mills that can quickly process metal, typically steel, into products such as structural steel (I-beams, angle stock, channel stock), bar stock, and rails. Most steel mills h ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ibeam
An I-beam is any of various structural members with an - (serif capital letter 'I') or H-shaped cross-section. Technical terms for similar items include H-beam, I-profile, universal column (UC), w-beam (for "wide flange"), universal beam (UB), rolled steel joist (RSJ), or double-T (especially in Polish, Bulgarian, Spanish, Italian, and German). I-beams are typically made of structural steel and serve a wide variety of construction uses. The horizontal elements of the are called flanges, and the vertical element is known as the "web". The web resists shear forces, while the flanges resist most of the bending moment experienced by the beam. The Euler–Bernoulli beam equation shows that the -shaped section is a very efficient form for carrying both bending and shear loads in the plane of the web. On the other hand, the cross-section has a reduced capacity in the transverse direction, and is also inefficient in carrying torsion, for which hollow structural sections are often ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fabrication (metal)
Metal fabrication is the creation of metal structures by cutting, bending and assembling processes. It is a value-added process involving the creation of machines, parts, and structures from various raw materials. Typically, a fabrication shop bids on a job, usually based on engineering drawings, and if awarded the contract, builds the product. Large fab shops employ a multitude of value-added processes, including welding, cutting, forming and machining. As with other manufacturing processes, both human labor and automation are commonly used. A fabricated product may be called a ''fabrication'', and shops specializing in this type of work are called ''fab shops''. The end products of other common types of metalworking, such as machining, metal stamping, forging, and casting, may be similar in shape and function, but those processes are not classified as fabrication. Processes *''Cutting'' is done by sawing, shear (sheet metal), shearing, or Chisel, chiselling (all with hand t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
The Morning Call
''The Morning Call'' is a daily newspaper in Allentown, Pennsylvania. Founded in 1883, it is the second-longest continuously published newspaper in the Lehigh Valley, after '' The Express-Times''. The newspaper is owned by Alden Global Capital, a New York Citybased hedge fund. In 2020, the newspaper permanently closed its Allentown headquarters after allegedly failing to pay four months of rent and citing diminishing advertising revenues. History 19th century ''The Morning Call'' was founded in 1883. Its original name was ''The Critic''. Its original editor, owner and chief reporter was Samuel S. Woolever. The newspaper's first reporter was a Muhlenberg College senior, David A. Miller. The newspaper was subsequently acquired by Charles Weiser, its editor, and Kirt W. DeBelle, its business manager. In 1894, the newspaper launched a reader contest, offering $5 in gold to a school boy or girl in Lehigh County who could guess the publication's new name. The identity of the l ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
