|
Cutback
Cutback or Cutbacks may refer to: * Cutback technique, a destructive technique for determining certain optical fiber transmission characteristics * Cutback (surfing move) * Cutback (roller coaster) This list of roller coaster elements contains the individual parts of roller coaster design and operation. Introduction Roller coaster elements are the individual parts of roller coaster design and operation, such as a track, hill, loop, or turn ..., a roller coaster inversion similar to a corkscrew * Cutback (football move), a sudden change in direction by a ball carrier in American football * "Cutbacks" (''30 Rock''), an episode of ''30 Rock'' {{disambiguation ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cutback (football Move)
A cutback is a sudden change in direction by a ball carrier in American football, usually against the flow of the play. One common type of cutback would be turning an end run into a run down the middle. It is a common type of juke Juke may refer to: * Juke (football move), a deceptive move in American football * "Juke" (song), a harmonica instrumental recorded by Little Walter Jacobs * Juke joint, an informal establishment featuring blues music, dancing, and alcoholic ... and the basis of the counter run. References {{Gridiron football maneuvers American football terminology ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cutback (roller Coaster)
This list of roller coaster elements contains the individual parts of roller coaster design and operation. Introduction Roller coaster elements are the individual parts of roller coaster design and operation, such as a track, hill, loop, or turn. Variations in normal track movement that add thrill or excitement to the ride are often called "thrill elements". Common elements Banked turn A banked turn is when the track twists from the horizontal plane into the vertical plane, tipping the train to the side in the direction of the turn. Banking is used to minimize the lateral G-forces on the riders to make the turn more comfortable. When a banked turn continues to create an upward or downward spiral of approximately 360 degrees or more, it becomes a helix. Brake run A brake run on a roller coaster is any section of track meant to slow or stop a roller coaster train. Brake runs may be located anywhere or hidden along the circuit of a coaster and may be designed to bring the train ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cutback (surfing Move)
Surfing is a surface water sport in which an individual, a surfer (or two in tandem surfing), uses a board to ride on the forward section, or face, of a moving wave of water, which usually carries the surfer towards the shore. Waves suitable for surfing are primarily found on ocean shores, but can also be found in standing waves in the open ocean, in lakes, in rivers in the form of a tidal bore, or in wave pools. The term ''surfing'' refers to a person riding a wave using a board, regardless of the stance. There are several types of boards. The Moche of Peru would often surf on reed craft, while the native peoples of the Pacific surfed waves on alaia, paipo, and other such water craft. Ancient cultures often surfed on their belly and knees, while the modern-day definition of surfing most often refers to a surfer riding a wave standing on a surfboard; this is also referred to as stand-up surfing. Another prominent form of surfing is body boarding, where a surfer rides th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cutback Technique
In telecommunications, a cutback technique is a destructive technique for determining certain optical fiber transmission characteristics, such as attenuation and bandwidth. Procedure The measurement technique consists of: #performing the desired measurements on a long length of the fiber under test, #cutting the fiber under test at a point near the launching end, #repeating the measurements on the short length of fiber, and #subtracting the results obtained on the short length to determine the results for the residual long length. The cut should be made to retain 1 meter or more of the fiber, in order to establish equilibrium mode distribution conditions for the second measurement. In a multimode fiber, the lack of an equilibrium mode distribution could introduce errors in the measurement due to output coupling effects. In a single-mode fiber, measuring a shorter cutback fiber could result in significant transmission of cladding modes (light carried in the cladding rather than ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
