|
Boom (sailing)
In sailing, a boom is a spar (sailing), spar (pole), along the of a fore and aft rigged sail, that greatly improves control of the angle and shape of the sail. The primary action of the boom is to keep the ''foot'' flatter when the sail angle is away from the centerline of the boat. The boom also serves as an attachment point for more sophisticated control lines. Because of the improved sail control it is rare to find a non-headsail without a boom, but lateen sails, for instance, are loose-footed. In some modern applications, the sail is rolled up into the boom for storage or reefing (shortening sail). Boom attachment The forward end of the boom attaches to a Mast (sailing), mast just below the sail, with a joint called the Gooseneck (sailing), gooseneck. The gooseneck pivots allowing the other end of the boom to move freely. The Parts of a sail#Corners, clew (back corner) of the sail attaches to the free end of the boom. The entire ''foot'' of the sail may be attached t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Sheet (sailing)
In sailing, a sheet is a line (rope, cable or chain) used to control the movable corner(s) (clews) of a sail. Terminology In nautical usage the term "sheet" is applied to a line or chain attached to the lower corners of a sail for the purpose of extension or change of direction. The connection in derivation with the root "shoot" is more clearly seen in "sheet-anchor", one that is kept in reserve, to be "shot" in case of emergency. Fore-and-aft rigs Fore-and-aft rigs comprise the vast majority of sailing vessels in use today, including effectively all dinghies and yachts. The sheet on a fore-and-aft sail controls the angle of the sail to the wind, and should be adjusted to keep the sail just filled. Most smaller boats use the Bermuda rig, which has two or three sets of sheets: * The mainsheet is attached to the boom, and is used to control the mainsail. In a rig with no boom on the mainsail, the mainsheet would attach directly to the mainsail clew. A mainsheet is a line con ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Aluminium
Aluminium (or aluminum in North American English) is a chemical element; it has chemical symbol, symbol Al and atomic number 13. It has a density lower than that of other common metals, about one-third that of steel. Aluminium has a great affinity towards oxygen, passivation (chemistry), forming a protective layer of aluminium oxide, oxide on the surface when exposed to air. It visually resembles silver, both in its color and in its great ability to reflect light. It is soft, magnetism, nonmagnetic, and ductility, ductile. It has one stable isotope, 27Al, which is highly abundant, making aluminium the abundance of the chemical elements, 12th-most abundant element in the universe. The radioactive decay, radioactivity of aluminium-26, 26Al leads to it being used in radiometric dating. Chemically, aluminium is a post-transition metal in the boron group; as is common for the group, aluminium forms compounds primarily in the +3 oxidation state. The aluminium cation Al3+ ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Furl (sailing)
Furling refers to stowing a sail into a neat package after it has been ed, but leaving it still fastened in the position from which it can be set. For a sail with a boom, this usually means flaking the sail down over the boom and securing it with sail ties. The headsail of a sloop (where roller furling is not fitted) is often lashed to a guardrail or along a bowsprit. A square sail is furled by gathering it more closely to the yard than is achieved by the buntlines and clewlines and securing it to the yard with gaskets image:gaskets.jpg, Some seals and gaskets A gasket is a Seal (mechanical), mechanical seal which fills the space between two or more mating surfaces, generally to prevent leakage from or into the joined objects while under compression (physical), .... When bending a sail onto a yard, a square sail is usually furled at deck level, being tied to itself with temporary lashings, so as to provide a controllable package to haul aloft and fasten to the yard. Less commo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Lazy Jack
Lazy jacks (or lazyjacks) are a type of rigging which can be applied to a fore-and-aft rigged sail to assist in sail handling during reefing and furling. They consist of a network of cordage which is rigged to a point on the mast and to a series of points on either side of the boom; these lines form a cradle which helps to guide the sail onto the boom when it is lowered, reducing the crew needed to secure the sail. Lazy jacks are most commonly associated with Bermuda rigged sails, although they can be used with gaff rigged sails and with club-footed jibs. Blocks and rings may be part of some lazyjacks. The oyster dredging sailboats of the Chesapeake Bay, bugeyes and skipjacks, were invariably equipped with lazy jacks, as their huge sail plans, combined with the changeable conditions on the bay, made it necessary to be able to reef quickly and with a small crew. Of late they have been revived as a feature of pleasure yachts as an alternative to roller reefing and furling. The ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Topping Lift
The topping lift (more rarely known as an uphaul) is a line which applies upward force on a boom on a sailboat. Part of the running rigging, topping lifts are primarily used to hold a boom up when the sail is lowered. This line would run from near the free end of the boom(s) forward to the top of the mast. The line may be run over a block at the top of the mast and down to the deck to allow it to be adjusted. For small booms, the topping lift may be run from end of the boom to the backstay or next mast aft. When the sail is raised again, the topping lift is loosened or removed. On sailboats used for racing, boom lift function is frequently incorporated into the boom vang system, to reduce the number of lines aloft. Allowing the vang to take this function also simplifies operation of the boat. On larger or older sailing vessels, lifts known as "quarter-lifts" run to the middle of the boom. When the sail is raised, the quarter-lift on the leeward side must be slack, otherwise ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Reefing
Reefing reduces the area of a sail, usually by folding or rolling one edge of the canvas in on itself and attaching the unused portion to a Spar (sailing), spar or a , as the primary measure to preserve a sailing vessel's stability in strong winds. Restoring full sail area is termed ''shaking out'' a . Whereas Fore-and-aft rig, fore-and-aft rigged vessels store the unused portion of the sail on a boom (sailing), boom (below the sail), square rig, square-rigged vessels stow the unused portion on a spar above the sail. Reefing may occur by rolling the sail around its Sail components, luff or Foot (sailing), foot, either on a rotating stay or within a spar. Fore-and-aft rigs Sails may have built-in alternative attachment points that allow their area to be reduced. In a mainsail, reefing cringles may be installed in the sail; a cruising boat will typically have two to three pairs. These are pulled down to the boom to form a new tack and clew, reducing the sail's area. The first ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Preventer
A gybe preventer, preventer, or jibe-guard, is a mechanical device on a sailing vessel which limits the boom's ability to swing unexpectedly across the boat due to an unplanned accidental jibe. During an unplanned accidental jibe (or ''gybe''), neither the crew nor the boat is set up properly to execute a planned jibe. As a result, the uncontrolled boom will swing across the boat potentially inflicting injury or knocking crew members overboard. The mainsheet or traveller can also inflict serious injury. Uncontrolled jibes may also damage the boat itself. Rigging a preventer on a yacht's mainsail is often performed when the wind is behind the beam (i.e. when it's coming from more than 90° off the bow). It can also be useful at other times when there is more swell than wind, a situation when the wind may not have the strength to keep the boom in place as the boat dips and rolls. On any boat that is sailing downwind without a preventer, strict 'heads-down' procedures must b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Boom Vang
A boom vang (US) or kicking strap (UK) (often shortened to "vang" or "kicker") is a line or piston system on a sailboat used to exert downward force on the boom and thus control the shape of the sail. The Collins English Dictionary defines it as "A rope or tackle extended from the boom of a fore-and-aft mainsail to a deck fitting of a vessel when running, in order to keep the boom from riding up". The vang typically runs from the base of the mast to the boom. Due to the great force necessary to change the height of the boom while a boat is under sail, a line-based boom vang usually includes some sort of a pulley system. Hydraulic piston vangs are used on larger sailboats and controlled by manual or electric hydraulic pumps. By controlling leech tension, the boom vang is one way of controlling sail twist. The boom vang may also be used to flatten the mainsail on dinghies A dinghy is a type of small boat, often carried or Towing, towed by a Watercraft, larger vesse ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Cunningham (sailing)
In sailing, a cunningham or cunningham's eye is a type of downhaul used on a Bermuda rigged sailboat to change the shape of a sail. It is named after its inventor, Briggs Cunningham, a victorious America's Cup skipper and yacht builder. The cunningham differs from a typical downhaul in the way that it attaches to the sail. The system usually consists of a line which is secured at one end to the mast or boom below the foot of the mainsail. It is then passed through a cringle in the luff of the sail near the foot but above the tack, and then led down on the other side to a fitting on the mast, boom or on deck. The tension in the luff of the sail is adjusted using a combination of the halyard and the cunningham (where fitted). The primary advantage of adjusting the cunningham is the speed and ease with which the luff tension can be changed while sailing or racing. By either hauling or easing the line, the tension in the luff can be changed, thereby shifting the point of maxim ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Downhaul
The downhaul is a line which is part of the rigging on a sailboat; it applies downward force on a spar or sail. The most common downhaul on a modern sailboat is attached to the spinnaker pole, though this may be referred to as the foreguy in some rigging nomenclature. The term is also commonly applied to the cunningham on the mainsail. In a windsurfing rig, the downhaul is the primary load-bearing line which controls the sail's shape. Modern windsurfing sails incorporate a sleeve for the mast, and therefore do not have a halyard In sailing, a halyard or halliard is a line (rope) that is used to hoist a ladder, sail, flag or yard. The term "halyard" derives from the Middle English ''halier'' ("rope to haul with"), with the last syllable altered by association with the E ... which tensions the top of the sail. The downhaul is tensioned early in the rigging process and is generally not adjustable on the water, and is therefore rather different in use than the downhaul on a sa ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
