|
ATM Adaptation Layer 5
ATM Adaptation Layer 5 (AAL5) is an ATM adaptation layer used to send variable-length packets up to 65,535 octets in size across an Asynchronous Transfer Mode (ATM) network. Unlike most network frames, which place control information in the header, AAL5 places control information in an 8-octet trailer at the end of the packet. The AAL5 trailer contains a 16-bit length field, a 32-bit cyclic redundancy check (CRC) and two 8-bit fields labeled ''UU'' and ''CPI'' that are currently unused. Each AAL5 packet is divided into an integral number of ATM cells and reassembled into a packet before delivery to the receiving host. This process is known as Segmentation and Reassembly (see below). The last cell contains padding to ensure that the entire packet is a multiple of 48 octets long. The final cell contains up to 40 octets of data, followed by padding bytes and the 8-octet trailer. In other words, AAL5 places the trailer in the last 8 octets of the final cell where it can be found ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
ATM Adaptation Layer
The use of Asynchronous Transfer Mode (ATM) technology and services creates the need for an adaptation layer in order to support information transfer protocols, which are not based on ATM. This adaptation layer defines how to segment higher-layer packets into cells and the reassembly of these packets. Additionally, it defines how to handle various transmission aspects in the ATM layer. Examples of services that need adaptations are Gigabit Ethernet, IP, Frame Relay, SONET/ SDH, UMTS/Wireless, etc. The main services provided by AAL (ATM Adaptation Layer) are: *Segmentation and reassembly *Handling of transmission errors *Handling of lost and misinserted cell conditions *Timing and flow control The following ATM Adaptation Layer protocols (AALs) have been defined by the ITU-T. It is meant that these AALs will meet a variety of needs. The classification is based on whether a timing relationship must be maintained between source and destination, whether the application requires ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Protocol (computing)
A communication protocol is a system of rules that allows two or more entities of a communications system to transmit information via any variation of a physical quantity. The protocol defines the rules, syntax, semantics, and synchronization of communication and possible error recovery methods. Protocols may be implemented by hardware, software, or a combination of both. Communicating systems use well-defined formats for exchanging various messages. Each message has an exact meaning intended to elicit a response from a range of possible responses predetermined for that particular situation. The specified behavior is typically independent of how it is to be implemented. Communication protocols have to be agreed upon by the parties involved. To reach an agreement, a protocol may be developed into a technical standard. A programming language describes the same for computations, so there is a close analogy between protocols and programming languages: ''protocols are to communica ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Virtual Circuit
A virtual circuit (VC) is a means of transporting data over a data network, based on packet switching and in which a connection is first established across the network between two endpoints. The network, rather than having a fixed data rate reservation per connection as in circuit switching, takes advantage of the statistical multiplexing on its transmission links, an intrinsic feature of packet switching. A 1978 standardization of virtual circuits by the CCITT imposes per-connection Flow control (data), flow controls at all user-to-network and network-to-network interfaces. This permits participation in congestion control and reduces the likelihood of packet loss in a heavily loaded network. Some circuit protocols provide Reliability (computer networking), reliable communication service through the use of data retransmissions invoked by error detection and automatic repeat request (ARQ). Before a virtual circuit may be used, it must be established between network nodes in the ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Internet Protocol
The Internet Protocol (IP) is the network layer communications protocol in the Internet protocol suite for relaying datagrams across network boundaries. Its routing function enables internetworking, and essentially establishes the Internet. IP has the task of delivering Packet (information technology), packets from the source Host (network), host to the destination host solely based on the IP addresses in the packet Header (computing), headers. For this purpose, IP defines packet structures that encapsulation (networking), encapsulate the data to be delivered. It also defines addressing methods that are used to label the datagram with source and destination information. IP was the connectionless datagram service in the original ''Transmission Control Program'' introduced by Vint Cerf and Bob Kahn in 1974, which was complemented by a connection-oriented service that became the basis for the Transmission Control Protocol (TCP). The Internet protocol suite is therefore often referre ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Subnetwork Access Protocol
The Subnetwork Access Protocol (SNAP) is a mechanism for multiplexing, on networks using IEEE 802.2 LLC, more protocols than can be distinguished by the eight-bit 802.2 Service Access Point (SAP) fields. SNAP supports identifying protocols by EtherType field values; it also supports vendor-private protocol identifier spaces. It is used with IEEE 802.3, IEEE 802.4, IEEE 802.5, IEEE 802.11 and other IEEE 802 physical network layers, as well as with non-IEEE 802 physical network layers such as FDDI that use 802.2 LLC. The SNAP and LSAP fields are added to the packets at the transmitting node in order to allow the receiving node to pass each received frame to an appropriate device driver which understands the given protocol. Background The OSI model uses a Service Access Point (SAP) to define the communication between layers (like Network, Transport, Session, and the other layers of the seven-layer model), that is to identify which protocol should process an incoming mes ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Logical Link Control
In the IEEE 802 reference model of computer networking, the logical link control (LLC) data communication protocol layer is the upper sublayer of the data link layer (layer 2) of the seven-layer OSI model. The LLC sublayer acts as an interface between the medium access control (MAC) sublayer and the network layer. The LLC sublayer provides multiplexing mechanisms that make it possible for several network protocols (e.g. IP, IPX and DECnet) to coexist within a multipoint network and to be transported over the same network medium. It can also provide flow control and automatic repeat request (ARQ) error management mechanisms. Operation The LLC sublayer is primarily concerned with multiplexing protocols transmitted over the MAC layer (when transmitting) and demultiplexing them (when receiving). It can also provide node-to-node flow control and error management. The flow control and error management capabilities of the LLC sublayer are used by protocols such as the NetBIO ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
IEEE 802
IEEE 802 is a family of Institute of Electrical and Electronics Engineers (IEEE) standards for local area networks (LANs), personal area networks (PANs), and metropolitan area networks (MANs). The IEEE 802 LAN/MAN Standards Committee (LMSC) maintains these standards. The IEEE 802 family of standards has had twenty-four members, numbered 802.1 through 802.24, with a working group of the LMSC devoted to each. However, not all of these working groups are currently active. The IEEE 802 standards are restricted to computer networks carrying variable-size packets, unlike cell relay networks, for example, in which data is transmitted in short, uniformly sized units called cells. Isochronous signal networks, in which data is transmitted as a steady stream of octet (computing), octets, or groups of octets, at regular time intervals, are also outside the scope of the IEEE 802 standards. The number 802 has no significance: it was simply the next number in the sequence that the IEEE used fo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Virtual Circuit Multiplexing
Virtual circuit multiplexing or VC-MUX is one of the two (the other being LLC encapsulation) mechanisms for identifying the protocol carried in ATM Adaptation Layer 5 (AAL5) frames specified by {{IETF RFC, 2684, Multiprotocol Encapsulation over ATM. With virtual circuit multiplexing, the communicating hosts agree to send only one packets belonging to a single high-level protocol on any given ATM virtual circuit, and multiple virtual circuits may need to be set up. It has the advantage of not requiring additional protocol-identifying information in a packet, which minimizes the overhead. For example, if the hosts agree to transfer IP, a sender can pass each datagram directly to AAL5 to transfer, nothing needs to be sent besides the datagram and the AAL5 trailer. This reduction in overhead tends to further improve efficiency (e.g., an IPv4 datagram containing a TCP ACK-only packet with neither IP nor TCP options exactly fits into a single ATM cell). The chief disadvantage of such a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Multiprotocol Encapsulation Over ATM
Multiprotocol Encapsulation over ATM is specified in RFC 2684. It defines two mechanisms for identifying the protocol carried in ATM Adaptation Layer 5 (AAL5) frames. It replaces RFC 1483, a standard data link access protocol supported by DSL modems. RFC 2684 describes two encapsulation mechanisms for network traffic: Virtual Circuit Multiplexing and LLC Encapsulation. Either mechanism carries either '' routed'' or '' bridged'' protocol data units, and DSL modems often include a setting for RFC 1483 bridging. This is distinct from other "bridge modes" commonly found in combined DSL modems and routers, which turn off the router portion of the DSL modem. In '' VC Multiplexing'' (VC-MUX), the hosts agree on the high-level protocol for a given circuit. It has the advantage of not requiring additional information in a packet, which minimises the overhead. For example, if the hosts agree to transfer IP, a sender can pass each datagram directly to AAL5 to transfer; nothing needs ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Application Software
Application software is any computer program that is intended for end-user use not operating, administering or programming the computer. An application (app, application program, software application) is any program that can be categorized as application software. Common types of applications include word processor, media player and accounting software. The term ''application software'' refers to all applications collectively and can be used to differentiate from system and utility software. Applications may be bundled with the computer and its system software or published separately. Applications may be proprietary or open-source. The short term ''app'' (coined in 1981 or earlier) became popular with the 2008 introduction of the iOS App Store, to refer to applications for mobile devices such as smartphones and tablets. Later, with introduction of the Mac App Store (in 2010) and Windows Store (in 2011), the term was extended in popular use to include desktop a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Packet (information Technology)
In telecommunications and computer networking, a network packet is a formatted unit of Data (computing), data carried by a packet-switched network. A packet consists of control information and user data; the latter is also known as the ''Payload (computing), payload''. Control information provides data for delivering the payload (e.g., source and destination network addresses, error detection codes, or sequencing information). Typically, control information is found in packet Header (computing), headers and Trailer (computing), trailers. In packet switching, the Bandwidth (computing), bandwidth of the transmission medium is shared between multiple communication sessions, in contrast to circuit switching, in which circuits are preallocated for the duration of one session and data is typically transmitted as a continuous bit stream. Terminology In the seven-layer OSI model of computer networking, ''packet'' strictly refers to a protocol data unit at layer 3, the network layer. A ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Segmentation And Reassembly
Segmentation and reassembly (SAR) is the process used to fragment and reassemble variable length Network packet, packets into fixed length cells so as to allow them to be transported across Asynchronous Transfer Mode (ATM) networks or other cell based infrastructures. Since ATM's payload is only 48 bytes, nearly every packet from any other protocol has to be processed in this way. Thus, it is an essential process for any ATM node. It is usually handled by a dedicated chip, called the SAR. The process is conceptually simple: an incoming packet from another protocol to be transmitted across the ATM network is chopped up into segments that fit into 48-byte chunks carried as ATM cell payloads. At the far end, these chunks are fitted back together to reconstitute the original packet. The process is analogous to the IP fragmentation, fragmentation of IP packets on reaching an interface with a maximum transmission unit (MTU) less than the packet size and the subsequent reassembly of ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
