|
Sync Word
In computer networks, a syncword, sync character, sync sequence or preamble is used to synchronize a data transmission by indicating the end of header information and the start of data. The syncword is a known sequence of data used to identify the start of a frame, and is also called ''reference signal'' or ''midamble'' in wireless communications. Prefix codes allow unambiguous identification of synchronization sequences and may serve as self-synchronizing code. Examples In an audio receiver receiving a bit stream of data, an example of a syncword is 0x0B77 for an AC-3 encoded stream. An Ethernet packet with the Ethernet preamble, 56 bits of alternating 1 and 0 bits, allowing the receiver to synchronize its clock to the transmitter, followed by a one-octet start frame delimiter byte and then the header. All USB packets begin with a sync field (8 bits long at low speed, 32 bits long at high speed) used to synchronize the receiver's clock to the transmitter's clock. A r ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Computer Network
A computer network is a set of computers sharing resources located on or provided by network nodes. The computers use common communication protocols over digital interconnections to communicate with each other. These interconnections are made up of telecommunication network technologies, based on physically wired, optical, and wireless radio-frequency methods that may be arranged in a variety of network topologies. The nodes of a computer network can include personal computers, servers, networking hardware, or other specialised or general-purpose hosts. They are identified by network addresses, and may have hostnames. Hostnames serve as memorable labels for the nodes, rarely changed after initial assignment. Network addresses serve for locating and identifying the nodes by communication protocols such as the Internet Protocol. Computer networks may be classified by many criteria, including the transmission medium used to carry signals, bandwidth, communications pro ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Data Link Layer
The data link layer, or layer 2, is the second layer of the seven-layer OSI model of computer networking. This layer is the protocol layer that transfers data between nodes on a network segment across the physical layer. The data link layer provides the functional and procedural means to transfer data between network entities and may also provide the means to detect and possibly correct errors that can occur in the physical layer. The data link layer is concerned with local delivery of frames between nodes on the same level of the network. Data-link frames, as these protocol data units are called, do not cross the boundaries of a local area network. Inter-network routing and global addressing are higher-layer functions, allowing data-link protocols to focus on local delivery, addressing, and media arbitration. In this way, the data link layer is analogous to a neighborhood traffic cop; it endeavors to arbitrate between parties contending for access to a medium, without c ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Magic Number (programming)
In computer programming, a magic number is any of the following: * A unique value with unexplained meaning or multiple occurrences which could (preferably) be replaced with a named constant * A constant numerical or text value used to identify a file format or protocol; for files, see List of file signatures * A distinctive unique value that is unlikely to be mistaken for other meanings (e.g., Globally Unique Identifiers) Unnamed numerical constants The term ''magic number'' or ''magic constant'' refers to the anti-pattern of using numbers directly in source code. This has been referred to as breaking one of the oldest rules of programming, dating back to the COBOL, FORTRAN and PL/1 manuals of the 1960s. The use of unnamed magic numbers in code obscures the developers' intent in choosing that number, increases opportunities for subtle errors (e.g. is every digit correct in 3.14159265358979323846 and is this equal to 3.14159?) and makes it more difficult for the program to be ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Automatic Baud Rate Detection
Automatic baud rate detection (ABR, autobaud) refers to the process by which a receiving device (such as a modem) determines the speed, code level, start bit, and stop bits of incoming data by examining the first character, usually a preselected sign-on character (syncword) on a UART connection. ABR allows the receiving device to accept data from a variety of transmitting devices operating at different speeds without needing to establish data rates in advance. During the autobaud process, the baud rate of received character stream is determined by examining the received pattern and its timing, and the length of a start bit. These type of baud rate detection mechanism are supported by many hardware chips including processors such aSTM32MPC8280, MPC8360, and so on. When start bit length is used to determine the baud rate, it requires the character to be odd since UART sends LSB bit first. Often symbols 'a' or 'A' (0x61 or 0x41) are used. For example, the MPC8270 SCC tries to d ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Channel Estimation
In wireless communications, channel state information (CSI) is the known channel properties of a communication link. This information describes how a signal propagates from the transmitter to the receiver and represents the combined effect of, for example, scattering, fading, and power decay with distance. The method is called Channel estimation. The CSI makes it possible to adapt transmissions to current channel conditions, which is crucial for achieving reliable communication with high data rates in multiantenna systems. CSI needs to be estimated at the receiver and usually quantized and feedback to the transmitter (although reverse-link estimation is possible in TDD systems). Therefore, the transmitter and receiver can have different CSI. The CSI at the transmitter and the CSI at the receiver are sometimes referred to as CSIT and CSIR, respectively. Different kinds of channel state information There are basically two levels of CSI, namely instantaneous CSI and statistica ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ethernet Frame
In computer networking, an Ethernet frame is a data link layer protocol data unit and uses the underlying Ethernet physical layer transport mechanisms. In other words, a data unit on an Ethernet link transports an Ethernet frame as its payload. An Ethernet frame is preceded by a preamble and start frame delimiter (SFD), which are both part of the Ethernet packet at the physical layer. Each Ethernet frame starts with an Ethernet header, which contains destination and source MAC addresses as its first two fields. The middle section of the frame is payload data including any headers for other protocols (for example, Internet Protocol) carried in the frame. The frame ends with a frame check sequence (FCS), which is a 32-bit cyclic redundancy check used to detect any in-transit corruption of data. Structure A data packet on the wire and the frame as its payload consist of binary data. Ethernet transmits data with the most-significant octet (byte) first; within each octet, ho ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Frame Synchronization
In telecommunication, frame synchronization or framing is the process by which, while receiving a stream of framed data, incoming frame alignment signals (i.e., a distinctive bit sequences or syncwords) are identified (that is, distinguished from data bits), permitting the data bits within the frame to be extracted for decoding or retransmission. Framing If the transmission is temporarily interrupted, or a bit slip event occurs, the receiver must re-synchronize. The transmitter and the receiver must agree ahead of time on which frame synchronization scheme they will use. Common frame synchronization schemes are: ;Framing bit: A common practice in telecommunications, for example in T-carrier, is to insert, in a dedicated time slot within the frame, a noninformation bit or framing bit that is used for synchronization of the incoming data with the receiver. In a bit stream, framing bits indicate the beginning or end of a frame. They occur at specified positions in the frame, d ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Digital Communication
Data transmission and data reception or, more broadly, data communication or digital communications is the transfer and reception of data in the form of a digital bitstream or a digitized analog signal transmitted over a point-to-point or point-to-multipoint communication channel. Examples of such channels are copper wires, optical fibers, wireless communication using radio spectrum, storage media and computer buses. The data are represented as an electromagnetic signal, such as an electrical voltage, radiowave, microwave, or infrared signal. Analog transmission is a method of conveying voice, data, image, signal or video information using a continuous signal which varies in amplitude, phase, or some other property in proportion to that of a variable. The messages are either represented by a sequence of pulses by means of a line code (''baseband transmission''), or by a limited set of continuously varying waveforms (''passband transmission''), using a digital modulation ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
CRC-based Framing
CRC-based framing is a kind of frame synchronization used in Asynchronous Transfer Mode (ATM) and other similar protocols. The concept of CRC-based framing was developed by StrataCom, Inc. in order to improve the efficiency of a pre-standard Asynchronous Transfer Mode (ATM) link protocol. This technology was ultimately used in the principal link protocols of ATM itself and was one of the most significant developments of StrataCom. An advanced version of CRC-based framing was used in the ITU-T SG15 G.7041 Generic Framing Procedure (GFP), which itself is used in several packet link protocols. Overview of CRC-based framing The method of CRC-Based framing re-uses the header cyclic redundancy check (CRC), which is present in ATM and other similar protocols, to provide framing on the link with no additional overhead. In ATM, this field is known as the Header Error Control/Check (HEC) field. It consists of the remainder of the division of the 32 bits of the header (taken as the coefficient ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Space (punctuation)
In writing, a space () is a blank area that separates words, sentences, syllables (in syllabification) and other written or printed glyphs (characters). Conventions for spacing vary among languages, and in some languages the spacing rules are complex. Inter-word spaces ease the reader's task of identifying words, and avoid outright ambiguities such as "now here" vs. "nowhere". They also provide convenient guides for where a human or program may start new lines. Typesetting can use spaces of varying widths, just as it can use graphic characters of varying widths. Unlike graphic characters, typeset spaces are commonly stretched in order to align text. The typewriter, on the other hand, typically has only one width for all characters, including spaces. Following widespread acceptance of the typewriter, some typewriter conventions influenced typography and the design of printed works. Computer representation of text facilitates getting around mechanical and physical limitations s ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Consistent Overhead Byte Stuffing
Consistent Overhead Byte Stuffing (COBS) is an algorithm for encoding data bytes that results in efficient, reliable, unambiguous packet framing regardless of packet content, thus making it easy for receiving applications to recover from malformed packets. It employs a particular byte value, typically zero, to serve as a ''packet delimiter'' (a special value that indicates the boundary between packets). When zero is used as a delimiter, the algorithm replaces each zero data byte with a non-zero value so that no zero data bytes will appear in the packet and thus be misinterpreted as packet boundaries. Byte stuffing is a process that transforms a sequence of data bytes that may contain 'illegal' or 'reserved' values (such as packet delimiter) into a potentially longer sequence that contains no occurrences of those values. The extra length of the transformed sequence is typically referred to as the overhead of the algorithm. HDLC framing is a well-known example, used particularly in ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
