|
Ripsaw
A ripsaw (or rip saw) is a wood saw that is specially designed for making a rip cut, a cut made parallel to the direction of the wood grain. Design The cutting edge of each tooth has a flat front edge and it is angled backward by about 8°, in contrast to a crosscut saw, which has teeth angled backward by about 15°. With the "rip" tooth pattern, the edges are sharpened at right angles to the cutting plane, forming chisel-like cutting surfaces, whereas crosscut teeth are sharpened at an angle, so that each tooth has a knife-like cutting point in contact with the wood. This design keeps the saw from following grain lines, which could curve the path of the saw: by acting like a chisel, the saw can more easily cut across deviating grain lines, which is necessary if a straight cut is to be achieved. This feature enables the orthogonal cutting edge to efficiently transport wood-chips from the kerf, allowing subsequent teeth to perform a more effective cut. It is possible to see ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Kerf
A saw is a tool consisting of a tough blade, wire, or chain with a hard toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power source. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. Terminology * Abrasive saw: A saw that cuts with an abrasive disc or band, rather than a toothed blade. * Back: the edge opposite the toothed edge. * Fleam: The angle of the faces of the teeth relative to a line perpendicular to the face of the saw. * Gullet: The valley between the points of the teeth. * Heel: The end closest to the handle. * Kerf: The narrow channel left behind by the saw and (relatedly) the measure of its width. The kerf depends on several factors: the width ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Saws
A saw is a tool consisting of a tough blade, wire, or chain with a hard toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power source. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. Terminology * Abrasive saw: A saw that cuts with an abrasive disc or band, rather than a toothed blade. * Back: the edge opposite the toothed edge. * Fleam: The angle of the faces of the teeth relative to a line perpendicular to the face of the saw. * Gullet: The valley between the points of the teeth. * Heel: The end closest to the handle. * Kerf: The narrow channel left behind by the saw and (relatedly) the measure of its width. The kerf depends on several factors: the width ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ripsaw
A ripsaw (or rip saw) is a wood saw that is specially designed for making a rip cut, a cut made parallel to the direction of the wood grain. Design The cutting edge of each tooth has a flat front edge and it is angled backward by about 8°, in contrast to a crosscut saw, which has teeth angled backward by about 15°. With the "rip" tooth pattern, the edges are sharpened at right angles to the cutting plane, forming chisel-like cutting surfaces, whereas crosscut teeth are sharpened at an angle, so that each tooth has a knife-like cutting point in contact with the wood. This design keeps the saw from following grain lines, which could curve the path of the saw: by acting like a chisel, the saw can more easily cut across deviating grain lines, which is necessary if a straight cut is to be achieved. This feature enables the orthogonal cutting edge to efficiently transport wood-chips from the kerf, allowing subsequent teeth to perform a more effective cut. It is possible to see ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rip Cut
The rift sawn rip cuts are perpendicular to the center of the log In woodworking, a rip-cut is a type of cut that severs or divides a piece of wood parallel to the grain. The other typical type of cut is a ''cross-cut'', a cut perpendicular to the grain. Unlike cross-cutting, which shears the wood fibers, a rip saw works more like a series of chisels, lifting off small splinters of wood. The nature of the wood grain requires the shape of the saw teeth to be different thus the need for both rip saws and crosscut saws; however some circular saw blades are ''combination blades'' and can make both types of cuts. A rip cut is the fundamental type of cut made at a sawmill. Definitions ''Rip cut'' comes from ''rip'': to split or saw timber in the direction of the grain, and ''cut'': to divide with a sharp-edged instrument."Rip v. 2." def. 2.a., "cut v." def. 7.a., "rive v.1." def. 4 and "kerf" def 2.a. ''Oxford English Dictionary'' Second Edition on CD-ROM (v. 4.0) © Oxford University P ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Wood Grain
Wood grain is the longitudinal arrangement of wood fibers or the pattern resulting from such an arrangement. Definition and meanings R. Bruce Hoadley wrote that ''grain'' is a "confusingly versatile term" with numerous different uses, including the direction of the wood cells (e.g., ''straight grain'', ''spiral grain''), surface appearance or figure, growth-ring placement (e.g., ''vertical grain''), plane of the cut (e.g., ''end grain''), rate of growth (e.g., ''narrow grain''), and relative cell size (e.g., ''open grain'').Hoadley, R. Bruce. "Glossary." ''Understanding Wood: A Craftsman's Guide to Wood Technology''. Newtown, Conn.: Taunton, 1980. 265. Print. Physical aspects Perhaps the most important physical aspect of wood grain in woodworking is the grain direction or slope (e.g. against the grain). The two basic categories of grain are straight and cross grain. Straight grain runs parallel to the longitudinal axis of the piece. Cross grain deviates from the longitudinal a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Crosscut Saw
A crosscut saw (thwart saw) is any saw designed for cutting wood perpendicular to (across) the wood grain. Crosscut saws may be small or large, with small teeth close together for fine work like woodworking or large for coarse work like log bucking, and can be a hand tool or power tool. The cutting edge of each tooth is angled in an alternating pattern. This design allows each tooth to act like a knife edge and slice through the wood in contrast to a rip saw, which tears along the grain, acting like a miniature chisel. Some crosscut saws use special teeth called "rakers" designed to clean out the cut strips of wood from the ''kerf''. Crosscut saws generally have smaller teeth than rip saws. Some saws, such as Japanese saws and those used by the ancient Egyptians, are designed to cut only on the pull stroke. Western saws, on the other hand, are designed to cut on the push stroke. Common features Many crosscut saws have a wooden handle with the return edge at right angle ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Chisel
A chisel is a tool with a characteristically shaped cutting edge (such that wood chisels have lent part of their name to a particular grind) of blade on its end, for carving or cutting a hard material such as wood, stone, or metal by hand, struck with a mallet, or mechanical power. The handle and blade of some types of chisel are made of metal or of wood with a sharp edge in it. Chiselling use involves forcing the blade into some material to cut it. The driving force may be applied by pushing by hand, or by using a mallet or hammer. In industrial use, a hydraulic ram or falling weight (' trip hammer') may be used to drive a chisel into the material. A gouge (one type of chisel) serves to carve small pieces from the material, particularly in woodworking, woodturning and sculpture. Gouges most frequently produce concave surfaces. A gouge typically has a 'U'-shaped cross-section. Etymology ''Chisel'' comes from the Old French ''cisel'', modern ''ciseau'', Late Latin ' ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Orthogonality
In mathematics, orthogonality is the generalization of the geometric notion of '' perpendicularity''. By extension, orthogonality is also used to refer to the separation of specific features of a system. The term also has specialized meanings in other fields including art and chemistry. Etymology The word comes from the Ancient Greek ('), meaning "upright", and ('), meaning "angle". The Ancient Greek (') and Classical Latin ' originally denoted a rectangle. Later, they came to mean a right triangle. In the 12th century, the post-classical Latin word ''orthogonalis'' came to mean a right angle or something related to a right angle. Mathematics Physics * In optics, polarization states are said to be orthogonal when they propagate independently of each other, as in vertical and horizontal linear polarization or right- and left-handed circular polarization. * In special relativity, a time axis determined by a rapidity of motion is hyperbolic-orthogonal to a space axis o ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Sawmill
A sawmill (saw mill, saw-mill) or lumber mill is a facility where logs are cut into lumber. Modern sawmills use a motorized saw to cut logs lengthwise to make long pieces, and crosswise to length depending on standard or custom sizes (dimensional lumber). The "portable" sawmill is of simple operation. The log lies flat on a steel bed, and the motorized saw cuts the log horizontally along the length of the bed, by the operator manually pushing the saw. The most basic kind of sawmill consists of a chainsaw and a customized jig ("Alaskan sawmill"), with similar horizontal operation. Before the invention of the sawmill, boards were made in various manual ways, either rived (split) and planed, hewn, or more often hand sawn by two men with a whipsaw, one above and another in a saw pit below. The earliest known mechanical mill is the Hierapolis sawmill, a Roman water-powered stone mill at Hierapolis, Asia Minor dating back to the 3rd century AD. Other water-powered mills followed ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Circular Saw
A circular saw is a power- saw using a toothed or abrasive disc or blade to cut different materials using a rotary motion spinning around an arbor. A hole saw and ring saw also use a rotary motion but are different from a circular saw. ''Circular saws'' may also be loosely used for the blade itself. Circular saws were invented in the late 18th century and were in common use in sawmills in the United States by the middle of the 19th century. A circular saw is a tool for cutting many materials such as wood, masonry, plastic, or metal and may be hand-held or mounted to a machine. In woodworking the term "circular saw" refers specifically to the hand-held type and the table saw and chop saw are other common forms of circular saws. "Skilsaw" and "Skil saw" have become generic trademarks for conventional hand-held circular saws. Circular saw blades are specially designed for each particular material they are intended to cut and in cutting wood are specifically designed for ma ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Band Saw
A bandsaw (also written band saw) is a power saw with a long, sharp blade consisting of a continuous band of toothed metal stretched between two or more wheels to cut material. They are used principally in woodworking, metalworking, and lumbering, but may cut a variety of materials. Advantages include uniform cutting action as a result of an evenly distributed tooth load, and the ability to cut irregular or curved shapes like a jigsaw.. The minimum radius of a curve is determined by the width of the band and its kerf. Most bandsaws have two wheels rotating in the same plane, one of which is powered, although some may have three or four to distribute the load. The blade itself can come in a variety of sizes and tooth pitches (teeth per inch, or TPI), which enables the machine to be highly versatile and able to cut a wide variety of materials including wood, metal and plastic. Almost all bandsaws today are powered by an electric motor. Line shaft versions were once common ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Reciprocating Saw
A reciprocating saw is a type of machine-powered saw in which the cutting action is achieved through a push-and-pull ("reciprocating") motion of the blade. The original trade name Sawzall is often used in the United States, where Milwaukee Electric Tool first produced a tool of this type in 1951. The term is commonly applied to a type of saw used in construction and demolition work. This type of saw, also known as a hognose or recip saw, has a large blade resembling that of a jigsaw and a handle oriented to allow the saw to be used comfortably on vertical surfaces. The typical design of this saw has a foot at the base of the blade, similar to that of a jigsaw. The user holds or rests this foot on the surface being cut so that the tendency of the blade to push away from or pull towards the cut as the blade travels through its movement can be countered. Design Designs range widely in power, speed, and features, from less powerful portable, handheld models that are usually shaped ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
