|
Physical Coding Sublayer
The physical coding sublayer (PCS) is a networking protocol sublayer in the Fast Ethernet, Gigabit Ethernet, and 10 Gigabit Ethernet standards. It resides at the top of the physical layer (PHY), and provides an interface between the physical medium attachment (PMA) sublayer and the media-independent interface (MII). It is responsible for data encoding and decoding, scrambling and descrambling, alignment marker insertion and removal, block and symbol redistribution, and lane block synchronization and deskew. Description The Ethernet PCS sublayer is at the top of the Ethernet physical layer (PHY). The hierarchy is as follows: * Data link layer (Layer 2) ** Logical link control (LLC) sublayer ** Medium access control (MAC) sublayer *** Reconciliation sublayer (RS)This sublayer processes PHY local/remote fault messages and handles DDR conversion * PHY Layer (Layer 1) ** Physical coding sublayer (PCS)This sublayer determines when a functional link has been established, provides rate ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fast Ethernet
In computer networking, Fast Ethernet Ethernet physical layer, physical layers carry traffic at the nominal rate of . The Classic Ethernet, prior Ethernet speed was . Of the Fast Ethernet physical layers, 100BASE-TX is by far the most common. Fast Ethernet was introduced in 1995 as the IEEE 802.3u standard and remained the fastest version of Ethernet for three years before the introduction of Gigabit Ethernet. The acronym ''GE/FE'' is sometimes used for devices supporting both standards. Nomenclature The ''100'' in the media type designation refers to the transmission speed of , while the ''BASE'' refers to baseband signaling. The letter following the dash (''T'' or ''F'') refers to the physical medium that carries the signal (twisted pair or fiber, respectively), while the last character (''X'', ''4'', etc.) refers to the line code method used. Fast Ethernet is sometimes referred to as 100BASE-X, where ''X'' is a placeholder for the FX and TX variants. General design Fast ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Manchester Code
In telecommunications and data storage, Manchester code (also known as phase encoding, or PE) is a line code in which the encoding of each data bit is either low then high, or high then low, for equal time. It is a self-clocking signal with no DC component. Consequently, electrical connections using a Manchester code are easily galvanically isolated. Manchester code derives its name from its development at the University of Manchester, where the coding was used for storing data on the magnetic drums of the Manchester Mark 1 computer. Manchester code was widely used for magnetic recording on 1600 bpi computer tapes before the introduction of 6250 bpi tapes which used the more efficient group-coded recording. Manchester code was used in early Ethernet physical layer standards and is still used in consumer IR protocols, RFID and near-field communication. It was and still is used for uploading commands to the Voyager spacecraft. Features Manchester coding is a spec ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Wavelength Division Multiplexing
In fiber-optic communications, wavelength-division multiplexing (WDM) is a technology which multiplexes a number of optical carrier signals onto a single optical fiber by using different wavelengths (i.e., colors) of laser light. This technique enables bidirectional communications over a single strand of fiber (also called wavelength-division duplexing) as well as multiplication of capacity. The term WDM is commonly applied to an optical carrier, which is typically described by its wavelength, whereas frequency-division multiplexing typically applies to a radio carrier, more often described by frequency. This is purely conventional because wavelength and frequency communicate the same information. Specifically, frequency (in Hertz, which is cycles per second) multiplied by wavelength (the physical length of one cycle) equals velocity of the carrier wave. In a vacuum, this is the speed of light (usually denoted by the lowercase letter, c). In glass fiber, velocity is substant ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SONET
Synchronous Optical Networking (SONET) and Synchronous Digital Hierarchy (SDH) are standardized protocols that transfer multiple digital bit streams synchronously over optical fiber using lasers or highly coherent light from light-emitting diodes (LEDs). At low transmission rates, data can also be transferred via an electrical interface. The method was developed to replace the plesiochronous digital hierarchy (PDH) system for transporting large amounts of telephone calls and data traffic over the same fiber without the problems of synchronization. SONET and SDH, which are essentially the same, were originally designed to transport circuit mode communications, e.g. DS1, DS3, from a variety of different sources. However, they were primarily designed to support real-time, uncompressed, circuit-switched voice encoded in PCM format. The primary difficulty in doing this prior to SONET/SDH was that the synchronization sources of these various circuits were different. This meant that ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
PAM-5
Pulse-amplitude modulation (PAM) is a form of signal modulation in which the message information is encoded in the amplitude of a pulse train interrupting the carrier frequency. Demodulation is performed by detecting the amplitude level of the carrier at every single period. Types There are two types of pulse amplitude modulation: * In ''single polarity PAM'', a suitable fixed DC bias is added to the signal to ensure that all the pulses are positive. * In ''double polarity PAM'', the pulses are both positive and negative. Pulse-amplitude modulation is widely used in modulating signal transmission of digital data, with non-baseband applications having been largely replaced by pulse-code modulation, and, more recently, by pulse-position modulation. The number of possible pulse amplitudes in analog PAM is theoretically infinite. Digital PAM reduces the number of pulse amplitudes to some natural number. Uses Ethernet Some versions of the Ethernet communication standard are a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Trellis Modulation
Trellis coded modulation (TCM) is a modulation scheme that transmits information with high efficiency over band-limited channels such as telephone lines. Gottfried Ungerboeck invented trellis modulation while working for IBM in the 1970s, and first described it in a conference paper in 1976. It went largely unnoticed, however, until he published a new, detailed exposition in 1982 that achieved sudden and widespread recognition. In the late 1980s, modems operating over plain old telephone service (''POTS'') typically achieved 9.6 kbit/s by employing four bits per symbol QAM modulation at 2,400 baud (symbols/second). This bit rate ceiling existed despite the best efforts of many researchers, and some engineers predicted that without a major upgrade of the public phone infrastructure, the maximum achievable rate for a POTS modem might be 14 kbit/s for two-way communication (3,429 baud × 4 bits/symbol, using QAM). 14 kbit/s is only 40% of the theoretical maximum bit ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Symbol Rate
In a digitally modulated signal or a line code, symbol rate, modulation rate or baud is the number of symbol changes, waveform changes, or signaling events across the transmission medium per unit of time. The symbol rate is measured in '' baud'' (Bd) or ''symbols per second''. In the case of a line code, the symbol rate is the pulse rate in pulses per second. Each symbol can represent or convey one or several bits of data. The symbol rate is related to the '' gross bit rate'', expressed in '' bits per second''. Symbols A symbol may be described as either a pulse in digital baseband transmission or a tone in passband transmission using modems. A symbol is a waveform, a state or a significant condition of the communication channel that ''persists'', for a fixed period of time. A sending device places symbols on the channel at a fixed and known symbol rate, and the receiving device has the job of detecting the sequence of symbols in order to reconstruct the transmitted data. The ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
8b/10b Encoding
In telecommunications, 8b/10b is a line code that maps 8-bit words to 10-bit symbols to achieve DC balance and bounded disparity, and at the same time provide enough state changes to allow reasonable clock recovery. This means that the difference between the counts of ones and zeros in a string of ''at least'' 20 bits is no more than two, and that there are not more than five ones or zeros in a row. This helps to reduce the demand for the lower bandwidth limit of the channel necessary to transfer the signal. An 8b/10b code can be implemented in various ways with focus on different performance parameters. One implementation was designed by K. Odaka for the DAT digital audio recorder. Kees Schouhamer Immink designed an 8b/10b code for the DCC audio recorder. The IBM implementation was described in 1983 by Al Widmer and Peter Franaszek. IBM implementation As the scheme name suggests, eight bits of data are transmitted as a 10-bit entity called a ''symbol'', or ''charac ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
4B5B
In telecommunications, 4B5B is a form of data communications line code. 4B5B maps groups of 4 bits of data onto groups of 5 bits for transmission. These 5-bit words are predetermined in a dictionary and they are chosen to ensure that there will be sufficient transitions in the line state to produce a self-clocking signal. A collateral effect of the code is that 25% more bits are needed to send the same information. An alternative to using 4B5B coding is to use a scrambler. Some systems use scramblers in conjunction with 4B5B coding to assure DC balance and improve electromagnetic compatibility. Depending on the standard or specification of interest, there may be several 5-bit output codes left unused. The presence of any of the unused codes in the data stream can be used as an indication that there is a fault somewhere in the link. Therefore, the unused codes can be used to detect errors in the data stream. Applications 4B5B was popularized by Fiber Distributed Data Int ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Nibble
In computing, a nibble, or spelled nybble to match byte, is a unit of information that is an aggregation of four- bits; half of a byte/ octet. The unit is alternatively called nyble, nybl, half-byte or tetrade. In networking or telecommunications, the unit is often called a semi-octet, quadbit, or quartet. As a nibble can represent sixteen () possible values, a nibble value is often shown as a hexadecimal digit (hex digit). A byte is two nibbles, and therefore, a value can be shown as two hex digits. Four-bit computers use nibble-sized data for storage and operations; as the word unit. Such computers were used in early microprocessors, pocket calculators and pocket computers. They continue to be used in some microcontrollers. In this context, 4-bit groups were sometimes also called characters rather than nibbles. History The term ''nibble'' originates from its representing half a byte, with ''byte'' a homophone of the English word ''bite''. In 2014, David B. Be ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Physical Medium Dependent
Physical medium dependent sublayers or PMDs further help to define the physical layer of computer network protocols. They define the details of transmission and reception of individual bits on a physical medium. These responsibilities encompass bit timing, signal encoding, interacting with the physical medium, and the properties of the cable, optical fiber, or wire itself. Common examples are specifications for Fast Ethernet, Gigabit Ethernet and 10 Gigabit Ethernet defined by the Institute of Electrical and Electronics Engineers (IEEE). For cable modems physical medium dependent sublayers define the physical sub-layer. Description The Ethernet PMD sublayer is part of the Ethernet physical layer (PHY). The hierarchy is as follows: * Data link layer (Layer 2) ** Logical link control (LLC) sublayer ** Medium access control (MAC) sublayer *** Reconciliation sublayer (RS)This sublayer processes PHY local/remote fault messages and handles DDR conversion * PHY layer (Layer 1) ** Physi ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Gigabit Ethernet
In computer networking, Gigabit Ethernet (GbE or 1 GigE) is the term applied to transmitting Ethernet frames at a rate of a gigabit per second. The most popular variant, 1000BASE-T, is defined by the IEEE 802.3ab standard. It came into use in 1999, and has replaced Fast Ethernet in wired local networks due to its considerable speed improvement over Fast Ethernet, as well as its use of cables and equipment that are widely available, economical, and similar to previous standards. The first standard for faster 10 Gigabit Ethernet was approved in 2002. History Ethernet was the result of research conducted at Xerox PARC in the early 1970s, and later evolved into a widely implemented Physical layer, physical and Data link layer, link layer protocol. Fast Ethernet increased the speed from 10 to 100 megabits per second (). Gigabit Ethernet was the next iteration, increasing the speed to . The initial standard for Gigabit Ethernet was produced by the IEEE in June 1998 as IEEE 802.3z ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
