|
Engine Configuration
The engine configuration describes the fundamental operating principles by which internal combustion engines are categorized. Piston engines are often categorized by their cylinder layout, valves and camshafts. Wankel engines are often categorized by the number of rotors present. Gas turbine engines are often categorized into turbojets, turbofans, turboprops and turboshafts. Piston engines Any design of motor/engine, be it a V or a boxer can be called an "in-line" if it's mounted in-line with the frame/chassis and in-line with the direction of travel of the vehicle. When the motor/engine is across the frame/chassis this is called a TRANSVERSE motor. Cylinder arrangement is not in the description of how the motor/engine is oriented. Therefore a V4 motor/engine can be a transverse or an in-line. Where the cylinders are arranged in two or more lines (such as in V engines or flat engines), each line of cylinders is referred to as a 'cylinder bank'. The angle between cylinder ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Internal Combustion Engine
An internal combustion engine (ICE or IC engine) is a heat engine in which the combustion of a fuel occurs with an oxidizer (usually air) in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons (reciprocating engine, piston engine), turbine blades (gas turbine), a Wankel engine, rotor (Wankel engine), or a propulsive nozzle, nozzle (jet engine). This force moves the component over a distance. This process transforms chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to. The first commercially successful internal combustion engines were invented in the mid-19th century. The first modern internal combustion engine, the Otto engine, was designed in 1876 by the German engineer Nicolaus ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Straight-three Engine
A straight-three engine (also called an inline-triple or inline-three) is a three-cylinder piston engine where cylinders are arranged in a line along a common crankshaft. Less common than straight-four engine, straight-three engines have nonetheless been used in various motorcycles, cars and agricultural machinery. Design A crankshaft angle of 120 degrees is typically used by straight-three engines, since this results in an evenly spaced firing interval. Another benefit of this configuration is perfect primary balance and secondary balance, however an end-to-end rocking couple is induced because there is no symmetry in the piston velocities about the middle piston. A balance shaft is sometimes used to reduce the vibrations caused by the rocking couple. Other crankshaft angles have been used occasionally. The 1976–1981 Laverda Jota motorcycle used a 180 degree crankshaft, where the outer pistons rise and fall together and inner cylinder is offset from them by 180 degrees ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V16 Engine
A V16 engine is a sixteen-cylinder Internal combustion engine#Reciprocating engines, piston engine where two banks of eight cylinders are arranged in a V engine, V configuration around a common crankshaft. V16 engines are less common than engines with fewer cylinders, such as V8 and V12 engines. Each bank of a V16 engine can be thought of as a straight-eight engine, straight-eight, a design that can be inherently engine balance, balanced. Most V16 engines have a 45° bank angle. The first use of a V16 engine was in the 1910 Antoinette VII experimental aircraft, followed by several cars in the 1930s. Today, the most common applications for V16 engines are railroad locomotives, marine craft, and stationary power generators. Automotive applications Production cars The first production car to use a V16 engine was the Cadillac V-16, introduced in January 1930. The Cadillac V16 engine was initially produced with a displacement of , overhead valve engine, OHV and a V-angle of 45 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V14 Engine
A V14 engine is a V engine with 14 cylinders mounted on the crankcase in two banks of seven cylinders. It is a very rare layout, used almost exclusively on large medium-speed diesel engines used for power generation and marine propulsion Marine propulsion is the mechanism or system used to generate thrust to move a watercraft through water. While paddles and sails are still used on some smaller boats, most modern ships are propelled by mechanical systems consisting of an electri .... Marine use MAN B&W offers V14 layout for its 32/40, 32/44CR, 48/60CR, 49/60DF, and 51/60DF engines, with outputs ranging from .Medium Speed Engine Project Planning Guides MAN Diesel & Turbo. MAN V14 engines have been installed on cruise ships such as the '' [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V12 Engine
A V12 engine is a twelve-Cylinder (engine), cylinder Internal combustion engine#Reciprocating engines, piston engine where two banks of six cylinders are arranged in a V engine, V configuration around a common crankshaft. V12 engines are more common than V10 engines. However, they are less common than V8 engines. The first V12 engine was built in 1904 for use in Boat racing, racing boats. Due to the balanced nature of the engine and the smooth delivery of Engine power, power, V12 engines were found in early luxury automobiles, boats, aircraft, and tanks. Aircraft V12 engines reached their apogee during World War II, after which they were mostly replaced by jet engines. In Formula One racing, V12 engines were common during the late 1960s and early 1990s. Applications of V12 engines in the 21st century have been as marine engines, in railway locomotives, as large stationary power as well as in some European sports and luxury cars. Design Balance and smoothness Each bank of a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V10 Engine
A V10 engine is a ten- cylinder piston engine where two banks of five cylinders are arranged in a V configuration around a common crankshaft. V10 engines are much less common than V8 and V12 engines. Several V10 diesel engines have been produced since 1965, and V10 petrol engines for road cars were first produced in 1991 with the release of the Dodge Viper. Design The V10 configuration does not have perfect engine balance, since an unbalanced rocking couple is caused by each cylinder bank functioning as a straight-five engine. Therefore, balance shafts are sometimes used to reduce the vibrations in a V10 engine. Diesel engines One of the first known V10 engines was used in the 1936 ''Busch-Sulzer ICRR 9201'' prototype locomotive, of which three examples were produced in the United States. The 1965–1984 Leopard 1 armored tank was powered by the ''MTU MB 838 CaM 500'' V10 diesel engine. Daimler-Benz produced three V10 diesel engine models (OM403, OM423 and OM443) ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V8 Engine
A V8 engine is an eight- cylinder piston engine in which two banks of four cylinders share a common crankshaft and are arranged in a V configuration. Origins The first known V8 was the Antoinette, designed by Léon Levavasseur, and built in 1904 by the French Antoinette company for use in speedboat racing, cars, and later, airplanes. Also in 1904, V8 engines began small-scale production by Renault and Buchet for use in race cars. Design V-angle Most engines use a V-angle (the angle between the two banks of cylinders) of 90 degrees. This angle results in good engine balance, which results in low vibrations. However, the downside is the greater width of the engine compared to those that use a smaller V-angle. V8 engines with a 60-degree V-angle were used in the 1996–1999 Ford Taurus SHO, the 2005–2011 Volvo XC90, and the 2006–2009 Volvo S80. The Ford engine used a 60-degree V-angle because it was based on a V6 engine with a 60-degree V-angle. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V6 Engine
A V6 engine is a six- cylinder piston engine where the cylinders and cylinder blocks share a common crankshaft and are arranged in a V configuration. The first V6 engines were designed and produced independently by Marmon Motor Car Company, Deutz Gasmotoren Fabrik and Delahaye. Engines built after World War II include the Lancia V6 engine in 1950 for the Lancia Aurelia, and the Buick V6 engine in 1962 for the Buick Special. The V6 layout has become the most common layout for six-cylinder automotive engines. Design Due to their short length, V6 engines are often used as the larger engine option for vehicles which are otherwise produced with inline-four engines, especially in transverse engine vehicles. A downside for luxury cars is that V6 engines produce more vibrations than straight-six engines. Some sports cars like the Porsche 911 use flat-six engines instead of V6 engines, due to their near perfect primary engine balance and lower centre of gravity (which ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V5 Engine
A V5 engine is a five-cylinder piston engine where the cylinders share a common crankshaft and are arranged in a V configuration. Even compared to the fairly rare straight-five engine, V5 engine designs are very uncommon. The first production V5 was the 1997–2007 Volkswagen Group VR5 engine. It is arguably not a true V5 engine, as all the cylinders share a single cylinder head. However, Honda produced a true V5 motorcycle racing engine, used in the RC211V. Automobiles General Motors In the early 1980s, Oldsmobile developed a prototype V5 diesel engine, however it never reached production stages and the project was subsequently abandoned. The engine is based on the Oldsmobile V6 diesel engine with the fuel injection pump in the location of the "missing" sixth cylinder. A prototype engine is on display at the RE Olds Museum in Lansing, Michigan. Volkswagen Group The only V5 automobile engine to reach production was the "VR5" engine manufactured by Volkswagen from 1997 t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V3 Engine
The V3 engine is a V engine with two cylinders in one bank and one cylinder in the other bank. It is a rare configuration, which has been mostly used in two-stroke engines for motorcycles competing in Grand Prix motorcycle racing. The first example was the 1955 DKW, DKW 350. The 1968 ''Suzuki RP68'' was intended to compete in the 1968 season, however a rule change mandating single-cylinder engines meant that the RP68 never raced. Honda later revived the layout for the 1982–1984 Honda NS500, NS500/NSR500 Grand Prix racing motorcycles. The 1983–1984 Honda MVX250F, MVX250F and 1985–1987 Honda NS400R, NS400R sports bikes also used V3 engines. In November 2024, Honda showed a prototype of a newly developed V3 engine paired to an electric supercharger. A related layout was the W3 engine, although this placed all three cylinders in the same plane, but none of them in the same bank. This was used for the 1905–1915 four-stroke engine, four-stroke Anzani 3-cylinder, Anzani en ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
IC Engine
An internal combustion engine (ICE or IC engine) is a heat engine in which the combustion of a fuel occurs with an oxidizer (usually air) in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons ( piston engine), turbine blades (gas turbine), a rotor (Wankel engine), or a nozzle (jet engine). This force moves the component over a distance. This process transforms chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to. The first commercially successful internal combustion engines were invented in the mid-19th century. The first modern internal combustion engine, the Otto engine, was designed in 1876 by the German engineer Nicolaus Otto. The term ''internal combustion engine'' usua ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Straight-eight Engine
The straight-eight engine or inline-eight engine (often abbreviated as I8) is an eight-cylinder internal combustion engine with all eight cylinders mounted in a straight line along the crankcase. The type has been produced in side-valve, IOE, overhead-valve, sleeve-valve, and overhead-cam configurations. A straight-eight can be timed for inherent primary and secondary balance, with no unbalanced primary or secondary forces or moments. However, crankshaft torsional vibration, present to some degree in all engines, is sufficient to require the use of a harmonic damper at the accessory end of the crankshaft. Without such damping, fatigue cracking near the rear main bearing journal may occur, leading to engine failure. Although an inline six-cylinder engine can also be timed for inherent primary and secondary balance, a straight-eight develops more power strokes per revolution and, as a result, will run more smoothly under load than an inline six. Also, due to the eve ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
