Submarine Communications Cables

A submarine communications cable is a cable laid on the sea bed between land-based stations to carry telecommunication signals across stretches of ocean and sea. The first submarine communications cables laid beginning in the 1850s carried telegraphy traffic, establishing the first instant telecommunications links between continents, such as the first transatlantic telegraph cable which became operational on 16 August 1858. Subsequent generations of cables carried telephone traffic, then data communications traffic. Modern cables use optical fibre technology to carry digital data, which includes telephone, Internet and private data traffic.

Modern cables are typically about in diameter and weigh around for the deep-sea sections which comprise the majority of the run, although larger and heavier cables are used for shallow-water sections near shore. Submarine cables first connected all the world's continents (except Antarctica) when Java was connected to Darwin, Northern Territory, Australia, in 1871 in anticipation of the completion of the Australian Overland Telegraph Line in 1872 connecting to Adelaide, South Australia and thence to the rest of Australia.

Early history: telegraph and coaxial cables

First successful trials

After William Cooke and Charles Wheatstone had introduced their working telegraph in 1839, the idea of a submarine line across the Atlantic Ocean began to be thought of as a possible triumph of the future. Samuel Morse proclaimed his faith in it as early as 1840, and in 1842, he submerged a wire, insulated with tarred hemp and India rubber, in the water of New York Harbor, and telegraphed through it. The following autumn, Wheatstone performed a similar experiment in Swansea Bay. A good insulator to cover the wire and prevent the electric current from leaking into the water was necessary for the success of a long submarine line. India rubber had been tried by Moritz von Jacobi, the Prussian electrical engineer, as far back as the early 19th century.

Another insulating gum which could be melted by heat and readily applied to wire made its appearance in 1842. Gutta-percha, the adhesive juice of the ''Palaquium gutta'' tree, was introduced to Europe by William Montgomerie, a Scottish surgeon in the service of the British East India Company. Twenty years earlier, Montgomerie had seen whips made of gutta-percha in Singapore, and he believed that it would be useful in the fabrication of surgical apparatus. Michael Faraday and Wheatstone soon discovered the merits of gutta-percha as an insulator, and in 1845, the latter suggested that it should be employed to cover the wire which was proposed to be laid from Dover to Calais. In 1847 William Siemens, then an officer in the army of Prussia, laid the first successful underwater cable using gutta percha insulation, across the Rhine between Deutz and Cologne. In 1849, Charles Vincent Walker, electrician to the South Eastern Railway, submerged of wire coated with gutta-percha off the coast from Folkestone, which was tested successfully.

First commercial cables

In August 1850, having earlier obtained a concession from the French government, John Watkins Brett's English Channel Submarine Telegraph Company laid the first line across the English Channel, using the converted tugboat ''Goliath''. It was simply a copper wire coated with gutta-percha, without any other protection, and was not successful. However, the experiment served to secure renewal of the concession, and in September 1851, a protected core, or true, cable was laid by the reconstituted Submarine Telegraph Company from a government hulk, ''Blazer'', which was towed across the Channel.

In 1853, more successful cables were laid, linking Great Britain with Ireland, Belgium, and the Netherlands, and crossing The Belts in Denmark. The British & Irish Magnetic Telegraph Company completed the first successful Irish link on May 23 between Portpatrick and Donaghadee using the collier ''William Hutt''. The same ship was used for the link from Dover to Ostend in Belgium, by the Submarine Telegraph Company. Meanwhile, the Electric & International Telegraph Company completed two cables across the North Sea, from Orford Ness to Scheveningen, the Netherlands. These cables were laid by ''Monarch'', a paddle steamer which later became the first vessel with permanent cable-laying equipment.

In 1858, the steamship ''Elba'' was used to lay a telegraph cable from Jersey to Guernsey, on to Alderney and then to Weymouth, the cable being completed successfully in September of that year. Problems soon developed with eleven breaks occurring by 1860 due to storms, tidal and sand movements, and wear on rocks. A report to the Institution of Civil Engineers in 1860 set out the problems to assist in future cable-laying operations.

Transatlantic telegraph cable

The first attempt at laying a transatlantic telegraph cable was promoted by Cyrus West Field, who persuaded British industrialists to fund and lay one in 1858. However, the technology of the day was not capable of supporting the project; it was plagued with problems from the outset, and was in operation for only a month. Subsequent attempts in 1865 and 1866 with the world's largest steamship, the SS ''Great Eastern'', used a more advanced technology and produced the first successful transatlantic cable. ''Great Eastern'' later went on to lay the first cable reaching to India from Aden, Yemen, in 1870.

British dominance of early cable

From the 1850s until 1911, British submarine cable systems dominated the most important market, the North Atlantic Ocean. The British had both supply side and demand side advantages. In terms of supply, Britain had entrepreneurs willing to put forth enormous amounts of capital necessary to build, lay and maintain these cables. In terms of demand, Britain's vast colonial empire led to business for the cable companies from news agencies, trading and shipping companies, and the British government. Many of Britain's colonies had significant populations of European settlers, making news about them of interest to the general public in the home country.

British officials believed that depending on telegraph lines that passed through non-British territory posed a security risk, as lines could be cut and messages could be interrupted during wartime. They sought the creation of a worldwide network within the empire, which became known as the All Red Line, and conversely prepared strategies to quickly interrupt enemy communications. Britain's very first action after declaring war on Germany in World War I was to have the cable ship ''Alert'' (not the CS '' Telconia'' as frequently reported) cut the five cables linking Germany with France, Spain and the Azores, and through them, North America. Thereafter, the only way Germany could communicate was by wireless, and that meant that Room 40 could listen in.

The submarine cables were an economic benefit to trading companies, because owners of ships could communicate with captains when they reached their destination and give directions as to where to go next to pick up cargo based on reported pricing and supply information. The British government had obvious uses for the cables in maintaining administrative communications with governors throughout its empire, as well as in engaging other nations diplomatically and communicating with its military units in wartime. The geographic location of British territory was also an advantage as it included both Ireland on the east side of the Atlantic Ocean and Newfoundland in North America on the west side, making for the shortest route across the ocean, which reduced costs significantly.

A few facts put this dominance of the industry in perspective. In 1896, there were 30 cable-laying ships in the world, 24 of which were owned by British companies. In 1892, British companies owned and operated two-thirds of the world's cables and by 1923, their share was still 42.7 percent. During World War I, Britain's telegraph communications were almost completely uninterrupted, while it was able to quickly cut Germany's cables worldwide.

Cable to India, Singapore, East Asia and Australia

Throughout the 1860s and 1870s, British cable expanded eastward, into the Mediterranean Sea and the Indian Ocean. An 1863 cable to Bombay (now Mumbai), India, provided a crucial link to Saudi Arabia. In 1870, Bombay was linked to London via submarine cable in a combined operation by four cable companies, at the behest of the British Government. In 1872, these four companies were combined to form the mammoth globe-spanning Eastern Telegraph Company, owned by John Pender. A spin-off from Eastern Telegraph Company was a second sister company, the Eastern Extension, China and Australasia Telegraph Company, commonly known simply as "the Extension". In 1872, Australia was linked by cable to Bombay via Singapore and China and in 1876, the cable linked the British Empire from London to New Zealand.

Submarine cables across the Pacific

The first trans-Pacific cables providing telegraph service were completed in 1902 and 1903, linking the US mainland to Hawaii in 1902 and Guam to the Philippines in 1903. Canada, Australia, New Zealand and Fiji were also linked in 1902 with the trans-Pacific segment of the All Red Line. Japan was connected into the system in 1906. Service beyond Midway Atoll was abandoned in 1941 due to World War II, but the remainder remained in operation until 1951 when the FCC gave permission to cease operations.

The first trans-Pacific telephone cable was laid from Hawaii to Japan in 1964, with an extension from Guam to The Philippines. Also in 1964, the Commonwealth Pacific Cable System (COMPAC), with 80 telephone channel capacity, opened for traffic from Sydney to Vancouver, and in 1967, the South East Asia Commonwealth (SEACOM) system, with 160 telephone channel capacity, opened for traffic. This system used microwave radio from Sydney to Cairns (Queensland), cable running from Cairns to Madang (Papua New Guinea), Guam, Hong Kong, Kota Kinabalu (capital of Sabah, Malaysia), Singapore, then overland by microwave radio to Kuala Lumpur. In 1991, the North Pacific Cable system was the first regenerative system (i.e., with repeaters) to completely cross the Pacific from the US mainland to Japan. The US portion of NPC was manufactured in Portland, Oregon, from 1989 to 1991 at STC Submarine Systems, and later Alcatel Submarine Networks. The system was laid by Cable & Wireless Marine on the '' CS Cable Venture''.

Construction

Transatlantic cables of the 19th century consisted of an outer layer of iron and later steel wire, wrapping India rubber, wrapping gutta-percha, which surrounded a multi-stranded copper wire at the core. The portions closest to each shore landing had additional protective armour wires. Gutta-percha, a natural polymer similar to rubber, had nearly ideal properties for insulating submarine cables, with the exception of a rather high dielectric constant which made cable capacitance high. William Thomas Henley had developed a machine in 1837 for covering wires with silk or cotton thread that he developed into a wire wrapping capability for submarine cable with a factory in 1857 that became W.T. Henley's Telegraph Works Co., Ltd. The India Rubber, Gutta Percha and Telegraph Works Company, established by the Silver family and giving that name to a section of London, furnished cores to Henley's as well as eventually making and laying finished cable. In 1870 William Hooper established Hooper's Telegraph Works to manufacture his patented vulcanized rubber core, at first to furnish other makers of finished cable, that began to compete with the gutta-percha cores. The company later expanded into complete cable manufacture and cable laying, including the building of the first cable ship specifically designed to lay transatlantic cables.

Gutta-percha and rubber were not replaced as a cable insulation until polyethylene was introduced in the 1930s. Even then, the material was only available to the military and the first submarine cable using it was not laid until 1945 during World War II across the English Channel. In the 1920s, the American military experimented with rubber-insulated cables as an alternative to gutta-percha, since American interests controlled significant supplies of rubber but did not have easy access to gutta-percha manufacturers. The 1926 development by John T. Blake of deproteinized rubber improved the impermeability of cables to water.

Many early cables suffered from attack by sea life. The insulation could be eaten, for instance, by species of ''Teredo'' (shipworm) and '' Xylophaga''. Hemp laid between the steel wire armouring gave pests a route to eat their way in. Damaged armouring, which was not uncommon, also provided an entrance. Cases of sharks biting cables and attacks by sawfish have been recorded. In one case in 1873, a whale damaged the Persian Gulf Cable between Karachi and Gwadar. The whale was apparently attempting to use the cable to clean off barnacles at a point where the cable descended over a steep drop. The unfortunate whale got its tail entangled in loops of cable and drowned. The cable repair ship ''Amber Witch'' was only able to winch up the cable with difficulty, weighed down as it was with the dead whale's body.

Bandwidth problems

Early long-distance submarine telegraph cables exhibited formidable electrical problems. Unlike modern cables, the technology of the 19th century did not allow for in-line repeater amplifiers in the cable. Large voltages were used to attempt to overcome the electrical resistance of their tremendous length but the cables' distributed capacitance and inductance combined to distort the telegraph pulses in the line, reducing the cable's bandwidth, severely limiting the data rate for telegraph operation to 10–12 words per minute.

As early as 1816, Francis Ronalds had observed that electric signals were retarded in passing through an insulated wire or core laid underground, and outlined the cause to be induction, using the analogy of a long Leyden jar. The same effect was noticed by Latimer Clark (1853) on cores immersed in water, and particularly on the lengthy cable between England and The Hague. Michael Faraday showed that the effect was caused by capacitance between the wire and the earth (or water) surrounding it. Faraday had noticed that when a wire is charged from a battery (for example when pressing a telegraph key), the electric charge in the wire induces an opposite charge in the water as it travels along. In 1831, Faraday described this effect in what is now referred to as Faraday's law of induction. As the two charges attract each other, the exciting charge is retarded. The core acts as a capacitor distributed along the length of the cable which, coupled with the resistance and inductance of the cable, limits the speed at which a signal travels through the conductor of the cable.

Early cable designs failed to analyse these effects correctly. Famously, E.O.W. Whitehouse had dismissed the problems and insisted that a transatlantic cable was feasible. When he subsequently became electrician of the Atlantic Telegraph Company, he became involved in a public dispute with William Thomson. Whitehouse believed that, with enough voltage, any cable could be driven. Thomson believed that his law of squares showed that retardation could not be overcome by a higher voltage. His recommendation was a larger cable. Because of the excessive voltages recommended by Whitehouse, Cyrus West Field's first transatlantic cable never worked reliably, and eventually short circuited to the ocean when Whitehouse increased the voltage beyond the cable design limit.

Thomson designed a complex electric-field generator that minimized current by resonating the cable, and a sensitive light-beam mirror galvanometer for detecting the faint telegraph signals. Thomson became wealthy on the royalties of these, and several related inventions. Thomson was elevated to Lord Kelvin for his contributions in this area, chiefly an accurate mathematical model of the cable, which permitted design of the equipment for accurate telegraphy. The effects of atmospheric electricity and the geomagnetic field on submarine cables also motivated many of the early polar expeditions.

Thomson had produced a mathematical analysis of propagation of electrical signals into telegraph cables based on their capacitance and resistance, but since long submarine cables operated at slow rates, he did not include the effects of inductance. By the 1890s, Oliver Heaviside had produced the modern general form of the telegrapher's equations, which included the effects of inductance and which were essential to extending the theory of transmission lines to the higher frequencies required for high-speed data and voice.

Transatlantic telephony

While laying a transatlantic telephone cable was seriously considered from the 1920s, the technology required for economically feasible telecommunications was not developed until the 1940s. A first attempt to lay a pupinized telephone cable failed in the early 1930s due to the Great Depression.

TAT-1 (Transatlantic No. 1) was the first transatlantic telephone cable system. Between 1955 and 1956, cable was laid between Gallanach Bay, near Oban, Scotland and Clarenville, Newfoundland and Labrador. It was inaugurated on September 25, 1956, initially carrying 36 telephone channels.

In the 1960s, transoceanic cables were coaxial cables that transmitted frequency-multiplexed voiceband signals. A high-voltage direct current on the inner conductor powered repeaters (two-way amplifiers placed at intervals along the cable). The first-generation repeaters remain among the most reliable vacuum tube amplifiers ever designed. Later ones were transistorized. Many of these cables are still usable, but have been abandoned because their capacity is too small to be commercially viable. Some have been used as scientific instruments to measure earthquake waves and other geomagnetic events.

Other uses

In 1942, Siemens Brothers of New Charlton, London, in conjunction with the United Kingdom National Physical Laboratory, adapted submarine communications cable technology to create the world's first submarine oil pipeline in Operation Pluto during World War II. Active fiber optic cables may be useful in detecting seismic events which alter cable polarization.

Modern history

Optical telecommunications cables

In the 1980s, fibre-optic cables were developed. The first transatlantic telephone cable to use optical fibre was TAT-8, which went into operation in 1988. A fibre-optic cable comprises multiple pairs of fibres. Each pair has one fibre in each direction. TAT-8 had two operational pairs and one backup pair. Except for very short lines, fibre-optic submarine cables include repeaters at regular intervals.

Modern optical fibre repeaters use a solid-state optical amplifier, usually an erbium-doped fibre amplifier. Each repeater contains separate equipment for each fibre. These comprise signal reforming, error measurement and controls. A solid-state laser dispatches the signal into the next length of fibre. The solid-state laser excites a short length of doped fibre that itself acts as a laser amplifier. As the light passes through the fibre, it is amplified. This system also permits wavelength-division multiplexing, which dramatically increases the capacity of the fibre.

Repeaters are powered by a constant direct current passed down the conductor near the centre of the cable, so all repeaters in a cable are in series. Power feed equipment is installed at the terminal stations. Typically both ends share the current generation with one end providing a positive voltage and the other a negative voltage. A virtual earth point exists roughly halfway along the cable under normal operation. The amplifiers or repeaters derive their power from the potential difference across them. The voltage passed down the cable is often anywhere from 3000 to 15,000VDC at a current of up to 1,100mA, with the current increasing with decreasing voltage; the current at 10,000VDC is up to 1,650mA. Hence the total amount of power sent into the cable is often up to 16.5 kW.

The optic fibre used in undersea cables is chosen for its exceptional clarity, permitting runs of more than between repeaters to minimize the number of amplifiers and the distortion they cause. Unrepeated cables are cheaper than repeated cables and their maximum transmission distance is limited, although this has increased over the years; in 2014 unrepeated cables of up to in length were in service; however these require unpowered repeaters to be positioned every 100 km.

The rising demand for these fibre-optic cables outpaced the capacity of providers such as AT&T. Having to shift traffic to satellites resulted in lower-quality signals. To address this issue, AT&T had to improve its cable-laying abilities. It invested $100 million in producing two specialized fibre-optic cable laying vessels. These included laboratories in the ships for splicing cable and testing its electrical properties. Such field monitoring is important because the glass of fibre-optic cable is less malleable than the copper cable that had been formerly used. The ships are equipped with thrusters that increase manoeuvrability. This capability is important because fibre-optic cable must be laid straight from the stern, which was another factor that copper-cable-laying ships did not have to contend with.

Originally, submarine cables were simple point-to-point connections. With the development of submarine branching units (SBUs), more than one destination could be served by a single cable system. Modern cable systems now usually have their fibres arranged in a self-healing ring to increase their redundancy, with the submarine sections following different paths on the ocean floor. One reason for this development was that the capacity of cable systems had become so large that it was not possible to completely back up a cable system with satellite capacity, so it became necessary to provide sufficient terrestrial backup capability. Not all telecommunications organizations wish to take advantage of this capability, so modern cable systems may have dual landing points in some countries (where back-up capability is required) and only single landing points in other countries where back-up capability is either not required, the capacity to the country is small enough to be backed up by other means, or having backup is regarded as too expensive.

A further redundant-path development over and above the self-healing rings approach is the mesh network whereby fast switching equipment is used to transfer services between network paths with little to no effect on higher-level protocols if a path becomes inoperable. As more paths become available to use between two points, it is less likely that one or two simultaneous failures will prevent end-to-end service.

As of 2012, operators had "successfully demonstrated long-term, error-free transmission at 100 Gbps across Atlantic Ocean" routes of up to , meaning a typical cable can move tens of terabits per second overseas. Speeds improved rapidly in the previous few years, with 40 Gbit/s having been offered on that route only three years earlier in August 2009.

Switching and all-by-sea routing commonly increases the distance and thus the round trip latency by more than 50%. For example, the round trip delay (RTD) or latency of the fastest transatlantic connections is under 60 ms, close to the theoretical optimum for an all-sea route. While in theory, a great circle route (GCP) between London and New York City is only , this requires several land masses (Ireland, Newfoundland, Prince Edward Island and the isthmus connecting New Brunswick to Nova Scotia) to be traversed, as well as the extremely tidal Bay of Fundy and a land route along Massachusetts' north shore from Gloucester to Boston and through fairly built up areas to Manhattan itself. In theory, using this partial land route could result in round trip times below 40 ms (which is the speed of light minimum time), and not counting switching. Along routes with less land in the way, round trip times can approach speed of light minimums in the long term.

The type of optical fiber used in unrepeated and very long cables is often PCSF (pure silica core) due to its low loss of 0.172 dB per kilometer when carrying a 1550 nm wavelength laser light. The large chromatic dispersion of PCSF means that its use requires transmission and receiving equipment designed with this in mind; this property can also be used to reduce interference when transmitting multiple channels through a single fiber using wavelength division multiplexing (WDM), which allows for multiple optical carrier channels to be transmitted through a single fiber, each carrying its own information. WDM is limited by the optical bandwidth of the amplifiers used to transmit data through the cable and by the spacing between the frequencies of the optical carriers; however this minimum spacing is also limited, with the minimum spacing often being 50 GHz (0.4 nm). The use of WDM can reduce the maximum length of the cable although this can be overcome by designing equipment with this in mind.

Optical post amplifiers, used to increase the strength of the signal generated by the optical transmitter often use a diode-pumped erbium-doped fiber laser. The diode is often a high power 980 or 1480 nm laser diode. This setup allows for an amplification of up to +24dBm in an affordable manner. Using an erbium-ytterbium doped fiber instead allows for a gain of +33dBm, however again the amount of power that can be fed into the fiber is limited. In single carrier configurations the dominating limitation is self phase modulation induced by the Kerr effect which limits the amplification to +18 dBm per fiber. In WDM configurations the limitation due to crossphase modulation becomes predominant instead. Optical pre-amplifiers are often used to negate the thermal noise of the receiver. Pumping the pre-amplifier with a 980 nm laser leads to a noise of at most 3.5 dB, with a noise of 5 dB usually obtained with a 1480 nm laser. The noise has to be filtered using optical filters.

Raman amplification