Shutdown is the state of a
nuclear reactor
A nuclear reactor is a device used to initiate and control a Nuclear fission, fission nuclear chain reaction. They are used for Nuclear power, commercial electricity, nuclear marine propulsion, marine propulsion, Weapons-grade plutonium, weapons ...
when the
fission reaction is slowed significantly or halted completely. Different nuclear reactor designs have different definitions for what "shutdown" means, but it typically means that the reactor is not producing a measurable amount of
electricity
Electricity is the set of physical phenomena associated with the presence and motion of matter possessing an electric charge. Electricity is related to magnetism, both being part of the phenomenon of electromagnetism, as described by Maxwel ...
or heat and is in a stable condition with very low
reactivity.
Definition
The shutdown margin for nuclear reactors (that is, when the reactor is considered to be safely in a shutdown state) is usually defined either in terms of reactivity or
dollars. For reactivity, this is calculated in units of delta-k/k, where k is equal to the
criticality of the reactor (essentially, how fast and controlled the nuclear fission reaction is). It is sometimes also measured in dollars, where one dollar is equal to a reactor in
prompt criticality
In nuclear engineering, prompt criticality is the criticality (the state in which a nuclear chain reaction is self-sustaining) that is achieved with prompt neutrons alone (without the efforts of delayed neutrons). As a result, prompt supercri ...
, this can then be used to calculate the change in reactivity required to shutdown or start up the reactor.
The shutdown margin for each reactor can either refer to the margin by which a reactor is subcritical with all its
control rods inserted, or as the margin by which the reactor would be shutdown in the event of a
SCRAM. This margin has to be considered carefully for each reactor and reactor design, to ensure that it remains within the technical specifications and limitations of the reactor.
Neutron poisoning
A reactor can be unintentionally "shutdown" by having an excess of
neutron poisons in the reactor vessel. Neutron poisons are chemical byproducts of the nuclear reaction which absorb
neutrons, lowering reactivity in the reactor and potentially stalling the reaction if enough poisons are allowed to build up.
An example of this would be the
Chernobyl disaster
On 26 April 1986, the no. 4 reactor of the Chernobyl Nuclear Power Plant, located near Pripyat, Ukrainian Soviet Socialist Republic, Ukrainian SSR, Soviet Union (now Ukraine), exploded. With dozens of direct casualties, it is one of only ...
in 1986, when Reactor No. 4 suffered from a serious
xenon-135
Xenon-135 (135Xe) is an Isotope#Radioactive, primordial, and stable isotopes, unstable isotope of xenon with a half-life of about 9.2 hours. 135Xe is a fission product of uranium and it is the most powerful known neutron-absorbing nuclear poison ...
poisoning, which pushed the reactor into an unstable condition which later caused the accident. While neutron poisoning is not considered a shutdown in and of itself, it often requires that the reactor be shutdown while the poisons are flushed from the system, as they can destabilise the reactor and cause it to behave unpredictably.
Certain reactors, such as the
CANDU reactor design (where it is called EPIS, or Emergency Poison Injection System), employ this phenomenon as part of their SCRAM procedure. When a SCRAM occurs, neutron poisons are injected into the reactor to immediately lower the reactivity of the reactor, at the same time or slightly prior to other shutdown mechanisms, such as control rods.
Cold shutdown
The difference between a normal (hot) shutdown and a cold shutdown is essentially that the fuel has gone completely or almost completely cold.
In a typical shutdown, regular levels of coolant are still required, and the fuel remains reasonably hot as it continues to react. In a cold shutdown, the coolant system is typically lowered to pump water at atmospheric pressure, and the
reactor vessel remains below 93 °C (200 °F). This temperature is so low that the cooling water in a
light-water reactor
The light-water reactor (LWR) is a type of thermal-neutron reactor that uses normal water, as opposed to heavy water, as both its coolant and neutron moderator; furthermore a solid form of fissile elements is used as fuel. Thermal-neutron reacto ...
does not boil or vaporise even if the pressure in the cooling circuit drops completely.
However no cold shutdown is possible after a
core meltdown, as the structure of the fuel rods and the coolant circuit is destroyed and the residues react in an uncontrolled manner, even if the pressure and temperature fulfil the conditions for cold shutdown, at least temporarily.
A cold shutdown is generally employed when operators need to access the reactor vessel for maintenance, fuel replenishing, or when the reactor has suffered damage of some kind that requires repairs. When a reactor is in cold shutdown, the fuel and control rods can be safely removed and exchanged, and maintenance can be performed. However, once a reactor has gone into a cold shutdown, it requires more time and energy to restart the chain reaction than if it had been in hot shutdown.
Cold shutdown
Glossary. Gesellschaft für Anlagen- und Reaktorsicherheit (GRS) gGmbH
See also
* Iodine pit
References
{{DEFAULTSORT:Shutdown (Nuclear Reactor)
Nuclear safety and security
Nuclear reactors