Schuko Plug Inserted In CEE 7 1 Ungrounded Socket

Schuko () or type F, is a connector (plug/socket) system used in much (but not all) of Europe. It is a registered trademark referring to a system of AC power plugs and sockets that is defined as " CEE7/3" (sockets) and "CEE7/4" (plugs). A Schuko plug features two round pins of diameter ( long, centres apart) for the line and neutral contacts, plus two flat contact areas on the top and bottom side of the plug for protective earth ( ground). The socket (which is often, in error, also referred to as CEE7/4) has a predominantly circular recess which is deep with two symmetrical round apertures and two earthing clips on the sides of the socket positioned to ensure that the earth is always engaged before live pin contact is made. Schuko plugs and sockets are symmetric AC connectors. They can be mated in two ways, therefore line can be connected to either pin of the appliance plug. As with most types of European sockets, Schuko sockets can accept Europlugs. Schuko plugs are considered a very safe design when used with Schuko sockets, but they can also mate with other sockets to give an unsafe result.

is a shortening of the German term ' (literally: protective contact), which indicates that plug and socket are equipped with protective-earth contacts (in the form of clips rather than pins). Schuko connectors are normally used on circuits with , , for currents up to , although e.g. South Korea uses them at for historical reasons.

History

The Schuko system originated in Germany. It is believed to date from 1925 and is attributed to Albert Büttner, a Bavarian manufacturer of electrical accessories. Büttner's company, , was granted patent DE 489003 in 1930 for a ('plug with earthing device'). Büttner's patent DE 370538 is often quoted as referring to Schuko, but it actually refers to a method of holding together all of the parts of a plug or socket with a single screw which also provides clamping for the wires; there is no mention of an earth connection in DE 370538. At this time Germany used a centre tap giving 127 V from current pins to earth, which meant that fuse links were required in both sides of the appliance and double pole switches. Variations of the original Schuko plug are used today in more than 40 countries, including most of Continental Europe.

France, Belgium, Czechia, Slovakia and Poland use the CEE7/6 plug and CEE7/5 socket (Type E) with the same size and spacing of the main pins but with a male protective-earth pin on the socket instead of the earth clips, and without the guiding notches at the sides. Most modern moulded Schuko plugs, and good-quality rewirable replacements, are a hybrid version ("CEE7/7") with an aperture that accommodates the earth pin of CEE7/5 sockets. CEE7/6 plugs that need to be polarised are configured in such a way as to only be inserted correctly in earthed sockets, however the old CEE7/1 2-pin unearthed socket is inherently dangerous with equipment that should be polarised, for example table lamps with an Edison screw lamp but only a single pole inline cord switch in lieu of a double pole switch. The safety of polarisation was not helped by several years of confusion when the correct connection of sockets was transposed.

Early in the 21st century, CEE7/7 became the ''de facto'' plug standard in many European countries, and in some other countries that follow CENELEC standards. European countries that do not use CEE7/7 are:
*Denmark (CEE7/17 and Danish standard 107-2-D1 are widely used, they accept CEE7/7 plugs but without compatibility for earth connections. CEE7/5 and CEE7/3 sockets with child-proof shutters have been allowed since 2008/2011, but are uncommon in buildings constructed before these dates).
*Ireland (BS1363 – equivalent Irish Standard: IS401) but see below,
*Italy ( CEI23-50 – includes Schuko),
*Malta (BS1363),
*Cyprus (BS1363),
*The United Kingdom, including Gibraltar ( BS1363)
*Switzerland ( SN441011)

In Italy, CEI 23-50 is the dominant standard and it also includes Schuko sockets (P30 = CEE7/3) and plugs (S30 = CEE7/4, S31 = CEE7/7, S32 = CEE7/17). Appliances are commonly sold with Schuko-type plugs (as well as Europlugs), while Italian-type plugs have become rare today and almost only power strips, cable reels and adaptors are sold with them. Some sockets (P30 and P40) accept both types, the remainder accepting one or the other. Schuko sockets are most commonly used for larger-rated appliances such as washing machines, and are particularly common in South Tyrol, with its cultural, economic and tourist connections with Austria.

Although Schuko has never been a standard (or the de facto norm) in Belgium or France, it is sometimes encountered in older installations in eastern regions of Belgium and Alsace.

In Ireland, Schuko was commonly installed until the 1960s. For safety reasons and to harmonize with the UK and thereby avoid having a different outlet type in Northern Ireland and the Republic of Ireland, the Republic standardized on BS 1363 (transposed into Irish Standards as IS401 (Plug) and IS411 (Socket outlet). Schuko has been phased out of use in Ireland and will be rarely encountered. Some hotels provide a Schuko outlet alongside BS1363 outlets for the convenience of visitors from the Continent.

Russia, while maintaining its own mains connector standard, has it largely harmonised with the relevant European regulations since Soviet times. The original Soviet standard was mostly compatible with Europlug (the traditional Soviet plug used straight pins with spacing and thus Soviet sockets were able to easily accept europlugs), and has been modified to accept pins, due to the large volume of imported appliances equipped with the Schuko plug. Nowadays most sold and installed sockets in Russia are Schuko ones, though they may lack a connection to earth, especially in older buildings, as this wasn't required by the Soviet wiring regulations.

Denmark gave full permission to install Schuko wall sockets in 2011, and such sockets can be found for sale at some Danish hardware stores, but the Danish Type K remains the most common earthed socket type in Denmark by far.

Safety features

CEE 7/3 refers to sockets, CEE 7/4 to plugs.

When inserted into the socket, the Schuko plug covers the socket cavity(1), thereby preventing users from touching connected pins. It also establishes protective-earth connection through the earth clips(2)''before'' the line and neutral pins(3)establish contact. A pair of non-conductive guiding notches(4)on the left and right side provides extra stability, enabling the safe use of large and heavy plugs (e.g. with built-in transformers or timers).

Some countries, including Portugal, Finland, Denmark,Danish Safety Technology Authority
/ref> Norway, Sweden, and Italy require child-proof socket shutters; the German DIN 49440-1:2006-01 standard does not have this requirement.

Compatibility with other plug/socket types

Schuko sockets can accept two-pin unearthed Europlug (CEE7/16) and CEE7/17. Less safely, Schuko plugs can be inserted into many two-pin unearthed CEE7/1 sockets and into some sockets with a different form of earth connection that will not mate with the earth contacts on the Schuko plug (e.g., some variants of the Danish socket). Many such sockets also lack the cavity required to prevent users from touching the pins whilst inserting the plug.

The CEE 7/7 plug is a hybrid which includes both side earthing strips, as in CEE7/4 Schuko, and an earthing aperture, as in the CEE7/6 plug. It can therefore achieve an earth contact with both CEE7/3 (Schuko) and CEE7/5 sockets.

In Italy, Chile, Peru and Uruguay, hybrid versions of Schuko sockets (called P30) are seen with an extra hole that will take the smaller variant of Italian CEI23-50 plugs. There are also hybrid Schuko sockets (called P40) with three extra holes and a wider cavity that will also accept the larger variant of Italian plugs.

Schuko sockets are unpolarised; there is no way of differentiating between the two live contacts (line which is approximately to earth and neutral which is approximately to earth) unless the voltage to earth is measured prior to use.

Although Schuko is incompatible and the pin spacing should not allow it, as the Schuko pins are slightly closer together, it is possible to dangerously force many Schuko round pin plugs (where the plastic is compliant enough) into many UK BS 1363 rectangular pin sockets, using a match or other probe to push into the earth shutter release. Due to the minimal contact area that must transmit high current, there is risk of overheating and thus fire. Where earthing is required, no earth contact will be made as Schuko plugs use side contacts for earthing rather than a third pin, and BS 1363 sockets have shutters that require the longer earth pin to be entered to open the line and neutral shutters, which prevent Europlugs and Schuko plugs from being inserted.

The IEC 60906-1 standard was intended to address some of the issues regarding polarisation and replace Schuko, but the only countries that have adopted it are South Africa and Brazil.

See also

* Europlug
* AC power plugs and sockets
* GOST 7396 Soviet version
* IEC 60906-1 proposed replacement since 1986

References

* German standard DIN VDE 0620-1; VDE 0620-1:2010-02 Plugs and socket-outlets for household and similar purposes - Part 1: General requirements (safety requirements)
* German standard DIN 49440-1:2006: Two-pole socket-outlets with earthing contact, AC - Part 1: Main dimensions (Schuko sockets)
* German standard DIN 49441:91972 Two-pole plugs with earthing-contact ≅ and –, ~: Main dimensions (Schuko plugs)
* IEC/TR 60083
{{refend

Mains power connectors