Run-out or runout is an inaccuracy of
rotating
Rotation, or spin, is the circular movement of an object around a '' central axis''. A two-dimensional rotating object has only one possible central axis and can rotate in either a clockwise or counterclockwise direction. A three-dimensional ...
mechanical systems, specifically that the tool or shaft does not rotate exactly
in line with the main axis. For example; when
drill
A drill is a tool used for making round holes or driving fasteners. It is fitted with a bit, either a drill or driver chuck. Hand-operated types are dramatically decreasing in popularity and cordless battery-powered ones proliferating due to ...
ing, run-out will result in a larger hole than the drill's nominal diameter due to the drill
being rotated
eccentrically (off axis instead of in line). In the case of
bearings, run-out will cause vibration of the machine and increased loads on the bearings.
Run-out is dynamic and cannot be compensated. If a rotating component, such as a drill chuck, does not hold the drill centrally, then as it rotates the rotating drill will turn about a secondary axis.
Run-out has two main forms:
* Radial run-out is caused by the tool being translated off the machine axis, still parallel. Radial run-out will measure the same all along the machine axis.
*
Axial
Axial may refer to:
* one of the anatomical directions describing relationships in an animal body
* In geometry:
:* a geometric term of location
:* an axis of rotation
* In chemistry, referring to an axial bond
* a type of modal frame, in music
* ...
run-out is caused by the tool or component being at an angle to the axis. Axial run-out causes the tip of the tool (or shaft) to rotate off centre relative to the base. Axial run-out will vary according to how far from the base it is measured.
In addition, irregular run-out is the result of worn or rough bearings which can manifest itself as either axial or radial run-out.
Runout will be present in any rotating system and, depending on the system, the different forms may either combine increasing total runout, or cancel reducing total runout. At any point along a tool or shaft it is not possible to determine whether runout is axial or radial; only by measuring along the axis can they be differentiated.
Absolute alignment is impossible; a degree of error will always be present.
Radial run-out
Radial run-out is the result of a rotating component running off centre, such as a ball bearing with an offset centre. This means that the rotating tool or shaft, instead of being centrally aligned, will rotate about a secondary axis. In general, cutting tools are more tolerant of radial run-out since the edges are parallel to the line of cutting tending to keep the tool tip aligned. However, a rotating shaft may be less tolerant of radial run-out since the centre of gravity is displaced by the amount of run-out.
Axial run-out
Axial run-out is the result of a rotating component not being parallel with the axis, such as a drill chuck not holding the drill exactly in line with the axis. In general, cutting tools are less tolerant of axial run-out since the tool tip tends to dig in and further increase run-out. However, a shaft may be more tolerant of axial run-out since the centre of gravity is displaced less.
Measurement
Typically run-out is measured using a
dial indicator
In various contexts of science, technology, and manufacturing (such as machining, fabricating, and additive manufacturing), an indicator is any of various instruments used to accurately measure small distances and angles, and amplify them to m ...
pressed against the rotating component while it is turned.
Total indicated run-out (TIR) is a technician's term for the measured run-out of any rotating system, including all forms of run-out, at the measured point.
See also
*
Nutation
Nutation () is a rocking, swaying, or nodding motion in the axis of rotation of a largely axially symmetric object, such as a gyroscope, planet, or bullet in flight, or as an intended behaviour of a mechanism. In an appropriate reference fra ...
*
Geometric dimensioning and tolerancing
Geometric Dimensioning and Tolerancing (GD&T) is a system for defining and communicating engineering tolerances and relationships. It uses a symbolic language on engineering drawings and computer-generated three-dimensional solid models that ex ...
References
{{Metalworking navbox, machopen
Mechanical engineering