Rock Analogs For Structural Geology on:
[Wikipedia]
[Google]
[Amazon]
This is a compilation of the properties of different analog materials used to simulate deformational processes in structural geology. Such experiments are often called analog or analogue models. The organization of this page follows the review of rock analog materials in structural geology and tectonics of Reber et al. 2020.
These materials need to exhibit brittle deformation upon failure as well as elastic and viscous deformation before failure.
Various fluids are used to simulate deformation of the lower crust and mantle, such as: linear, non-linear, and yield stress fluids.
Composite materials combine phases with different physical properties. A common composite mixture contains dry granular materials and fluids. These analog materials have been used:
* Sediment transport (Parker et al., 1982) using low viscosity fluids
* Dynamics in the middle crust (Mookerjee et al., 2017; Reber et al., 2014Reber, J. E., Hayman, N. W., & Lavier, L. L. (2014). Stick-slip and creep behavior in lubricated granular material: insights into the brittle-ductile transition. ''Geophysical Research Letters, 41'', 3471-3477.) employing high viscosity fluids
* Stick-slip dynamics (Higashi and Sumita, 2009; Reber et al., 2014)
* Strain softening and hardening processes (Panien et al., 2006)
The most commonly used granular materials in composite mixtures are:
* Sand
* Glass beads
* Acrylic discs
Common fluids used in composite mixtures are:
* Carbopol
* Silicone
* Wax, which can behave as a brittle or viscous material depending on the melting temperature (Mookerjee et al., 2017)
Materials used to simulate upper crustal deformation
These materials need to exhibit brittle deformation upon failure as well as elastic and viscous deformation before failure.
Materials that simulate upper crustal deformation
Dry granular materials
Materials used to simulate deformation of the lower crust and mantle
Various fluids are used to simulate deformation of the lower crust and mantle, such as: linear, non-linear, and yield stress fluids.
Materials used to simulate deformation of the middle crust
Composite Model Materials
Composite materials combine phases with different physical properties. A common composite mixture contains dry granular materials and fluids. These analog materials have been used:
* Sediment transport (Parker et al., 1982) using low viscosity fluids
* Dynamics in the middle crust (Mookerjee et al., 2017; Reber et al., 2014Reber, J. E., Hayman, N. W., & Lavier, L. L. (2014). Stick-slip and creep behavior in lubricated granular material: insights into the brittle-ductile transition. ''Geophysical Research Letters, 41'', 3471-3477.) employing high viscosity fluids
* Stick-slip dynamics (Higashi and Sumita, 2009; Reber et al., 2014)
* Strain softening and hardening processes (Panien et al., 2006)
The most commonly used granular materials in composite mixtures are:
* Sand
* Glass beads
* Acrylic discs
Common fluids used in composite mixtures are:
* Carbopol
* Silicone
* Wax, which can behave as a brittle or viscous material depending on the melting temperature (Mookerjee et al., 2017)
Visco-elasto-plastic model materials
Visco-elasto-plastic deformation exhibits a combination of elastic, viscous, and plastic deformation at the same time. Various asphalts and bituminous materials demonstrate visco-elasto-plastic deformation but they are rarely as modeling materials (McBirney and Best, 1961).Common modeling materials demonstrating complex rheology are; * Carbopol (Piau, 2007; Shafiei et al., 2018) *Kaolinite clay (Cooke and van der Elst, 2012)References
{{reflist Structural geology Earth sciences Deformation (mechanics)