A percolation test (colloquially called a perc test) is a test to determine the water absorption rate of

soil Soil, also commonly referred to as earth, is a mixture of organic matter, minerals, gases, water, and organisms that together support the life of plants and soil organisms. Some scientific definitions distinguish dirt from ''soil'' by re ...

(that is, its capacity for

percolation In physics, chemistry, and materials science, percolation () refers to the movement and filtration, filtering of fluids through porous materials. It is described by Darcy's law. Broader applications have since been developed that cover connecti ...

) in preparation for the building of a septic drain field (leach field) or infiltration basin. The results of a percolation test are required to design a septic system properly. In its broadest terms, percolation testing observes how quickly a known volume of water dissipates into the subsoil of a drilled hole of known surface area. While every jurisdiction will have laws regarding the exact calculations for the length of line, depth of pit, etc., the testing procedures are the same. In general,

sand Sand is a granular material composed of finely divided mineral particles. Sand has various compositions but is usually defined by its grain size. Sand grains are smaller than gravel and coarser than silt. Sand can also refer to a textural ...

y soil will absorb more water than soil with a high concentration of clay or where the

water table The water table is the upper surface of the phreatic zone or zone of saturation. The zone of saturation is where the pores and fractures of the ground are saturated with groundwater, which may be fresh, saline, or brackish, depending on the loc ...

is close to the surface.

Testing method

A percolation test consists of digging one or more holes in the soil of the proposed leach field to a specified depth, presoaking the holes by maintaining a high water level in the holes, then running the test by filling the holes to a specific level and timing the drop of the water level as the water percolates into the surrounding soil. There are various empirical formulae for determining the required size of a leach field based on the size of the facility, the percolation test results, and other parameters. For leach line testing, at least three test holes are drilled or dug by hand, most commonly six to eight inches in diameter. These should be drilled to depths three to six feet below the surface. For better, more conclusive results, five drill holes are used in a pattern of one hole at each corner of the proposed leach field and one test hole in the center. Testing these holes will result in a value with units of minutes per inch. This value is then correlated to a predetermined county health code to establish the exact size of the leach field. Testing for horizontal pits typically requires five to eight test holes drilled in a straight line or along a common contour from three to ten feet below the surface. This testing is identical to leach line testing, though the result is a different type of septic system established through a different calculation.

\text =  = \;\text

Vertical seepage pits differ slightly in testing methods due to their large size, but the primary testing method is essentially the same. A hole, typically three to four feet in diameter, is drilled to a depth of twenty or thirty feet (depending on the local groundwater table). A fire hose is used to fill the pit as quickly as possible, and then, again, its dissipation rate is observed. This rate calculates the size and number of pits necessary for a viable septic system. Finally, a "deep hole" is drilled to find the water table or to approximately twelve feet (dry) for leach line systems and horizontal seepage pits. Exact depths will again depend on local health codes. In the case of a vertical seepage pit, local groundwater data may be used, or if the drill hole reaches groundwater, the pit will be backfilled again according to the county health code.

Alternatives

Some jurisdictions question the accuracy of a percolation test to assess soil treatment quality and instead utilize

soil texture Soil texture is a soil classification, classification instrument used both in the field and laboratory to determine soil classes based on their physical texture. Soil texture can be determined using qualitative methods such as texture by feel, and ...

analysis—along with long-term acceptance rates (LTAR)—in place of or in addition to a percolation test.

References

{{Reflist
How to Run a Percolation Test
Sewerage Soil physics