off-by-one errors

An off-by-one error or off-by-one bug (known by acronyms OBOE, OBOB, OBO and OB1) is a logic error that involves a number that differs from its intended value by 1. An off-by-one error can sometimes appear in a mathematical context. It often occurs in computer programming when a loop iterates one time too many or too few, usually caused by the use of non-strict inequality (≤) as the terminating condition where strict inequality (<) should have been used, or vice versa. Off-by-one errors also stem from confusion over zero-based numbering.

Cases

Looping over arrays

Consider an array of items, and items ''m'' through ''n'' (inclusive) are to be processed. How many items are there? An intuitive answer may be , but that is off by one, exhibiting a fencepost error; the correct answer is .

For this reason, ranges in computing are often represented by half-open intervals; the range from ''m'' to ''n'' (inclusive) is represented by the range from ''m'' (inclusive) to (exclusive) to avoid fencepost errors. For example, a loop that iterates five times (from 0 to 4 inclusive) can be written as a half-open interval from 0 to 5:

for (index = 0; index < 5; index++)

The loop body is executed first of all with equal to 0; then becomes 1, 2, 3, and finally 4 on successive iterations. At that point, becomes 5, so is false and the loop ends. However, if the comparison used were <= (less than or equal to), the loop would be carried out six times: takes the values 0, 1, 2, 3, 4, and 5. Likewise, if were initialized to 1 rather than 0, there would only be four iterations: takes the values 1, 2, 3, and 4. Both of these alternatives can cause off-by-one errors.

Another such error can occur if a do-while loop is used in place of a while loop (or vice versa.) A do-while loop is guaranteed to run at least once.

Array-related confusion may also result from differences in programming languages. Numbering from 0 is most common, but some languages start array numbering with 1. Pascal has arrays with user-defined indices. This makes it possible to model the array indices after the problem domain.

Fencepost error

A fencepost error (occasionally called a telegraph pole, lamp-post, or picket fence error) is a specific type of off-by-one error. An early description of this error appears in the works of Vitruvius.. The following problem illustrates the error:

The common answer of 10 posts is wrong. This response comes from dividing the length of the fence by the spacing apart from each post, with the quotient being erroneously classified as the number of posts. In actuality, the fence has 10 sections and 11 posts.

In this scenario, a fence with ''n'' sections will have posts. Conversely, if the fence contains ''n'' posts, it will contain sections. This relationship is important to consider when dealing with the reverse error. The reverse error occurs when the number of posts is known and the number of sections is assumed to be the same. Depending on the design of the fence, this assumption can be correct or incorrect.

The following problem demonstrates the reverse error:

The interpretation for the fence's design changes the answer to this problem. The correct number of sections for a fence is if the fence is a free-standing line segment bounded by a post at each of its ends (e.g., a fence between two passageway gaps), ''n'' if the fence forms one complete, free-standing loop (e.g., enclosure accessible by surmounting, such as a boxing ring), or if posts do not occur at the ends of a line-segment-like fence (e.g., a fence between and wall-anchored to two buildings). The precise problem definition must be carefully considered, as the setup for one situation may give the wrong answer for other situations.

Fencepost errors can also occur in units other than length. For example, the Time Pyramid, consisting of 120 blocks placed at 10-year intervals between blocks, is scheduled to take 1,190 years to build (not 1,200), from the installation of the first block to the last block. One of the earliest fencepost errors involved time, where the Julian calendar originally calculated leap years incorrectly, due to counting inclusively rather than exclusively, yielding a leap year every three years rather than every four.

In larger numbers, being off by one is often not a major issue. In smaller numbers, however, and specific cases where accuracy is paramount, committing an off-by-one error can be disastrous. Sometimes such an issue will also be repeated and, therefore, worsened, by someone passing on an incorrect calculation, if the following person makes the same kind of mistake again (of course, the error might also be reversed).

An example of this error can occur in the computational language MATLAB with the linspace() linear interpolation function, whose parameters are (''lower value'', ''upper value'', ''number of values'') and not (''lower value'', ''upper value'', ''number of increments''). A programmer who misunderstands the third parameter to be the number of increments might hope that linspace(0,10,5) would achieve a sequence but instead would get .

Security implications

A common off-by-one error which results in a security-related bug is caused by misuse of the C standard library strncat routine. A common misconception with strncat is that the guaranteed null termination will not write beyond the maximum length. In reality it will write a terminating null character one byte beyond the maximum length specified. The following code contains such a bug:

void foo (char *s)

Off-by-one errors are common in using the C library because it is not consistent with respect to whether one needs to subtract 1 byte – functions like fgets() and strncpy will never write past the length given them (fgets() subtracts 1 itself, and only retrieves bytes), whereas others, like strncat will write past the length given them. So the programmer has to remember for which functions they need to subtract 1.

On some systems (little endian architectures in particular) this can result in the overwriting of the least significant byte of the frame pointer. This can cause an exploitable condition where an attacker can hijack the local variables for the calling routine.

One approach that often helps avoid such problems is to use variants of these functions that calculate how much to write based on the total length of the buffer, rather than the maximum number of characters to write. Such functions include strlcat and strlcpy, and are often considered "safer" because they make it easier to avoid accidentally writing past the end of a buffer. (In the code example above, calling strlcat(buf, s, sizeof(buf)) instead would remove the bug.)

See also

* Boundary-value analysis
* Pigeonhole principle
* Rounding error
* Zero-based numbering

References

Citations

Sources

* ''An earlier version of this article was based o
fencepost error
a
FOLDOC
used with permission.''
*
* In the Common Weakness Enumeration system this issue is listed a
CWE-193: Off-by-one Error

Further reading

*

{{DEFAULTSORT:Off-By-One Error
Software bugs
Articles with example C code