Luminol2006

Luminol (C₈H₇N₃O₂) is a chemical that exhibits chemiluminescence, with a blue glow, when mixed with an appropriate oxidizing agent. Luminol is a white-to-pale-yellow crystalline solid that is soluble in most polar organic solvents but insoluble in water.

Forensic investigators use luminol to detect trace amounts of blood at crime scenes, as it reacts with the iron in hemoglobin. Biologists use it in cellular assays to detect copper, iron, and cyanides as well as specific proteins via western blotting.

When luminol is sprayed evenly across an area, trace amounts of an activating oxidant make the luminol emit a blue glow that can be seen in a darkened room. The glow only lasts about 30 seconds but can be documented photographically. The glow is stronger in areas receiving more spray; the intensity of the glow does not indicate the amount of blood or other activator present.

Synthesis

Luminol is synthesized in a two-step process, beginning with 3-nitrophthalic acid. First, hydrazine (N₂H₄) is heated with the 3-nitrophthalic acid in a high-boiling solvent such as triethylene glycol and glycerol. A condensation reaction occurs, with loss of water, forming 3-nitrophthalhydrazide. Reduction of the nitro group to an amino group with sodium dithionite (Na₂S₂O₄), via a transient hydroxylamine intermediate, produces luminol.

:

The compound was first synthesized in Germany in 1902 but was not named ''luminol'' until 1934.

Chemiluminescence

To exhibit its luminescence, the luminol must be activated with an oxidant. Usually, a solution containing hydrogen peroxide (H₂O₂) and hydroxide ions in water is the activator. In the presence of a catalyst such as an iron or periodate compound, the hydrogen peroxide decomposes to form oxygen and water:

:2 H₂O₂ → + 2 H₂O
:H₂O₂ + KIO₄ → KIO₃ + O₂ + H₂O

Laboratory settings often use potassium ferricyanide or potassium periodate for the catalyst. In the forensic detection of blood, the catalyst is the iron present in hemoglobin. Enzymes in a variety of biological systems may also catalyse the decomposition of hydrogen peroxide.

The exact mechanism of luminol chemiluminescence is a complex multi-step reaction, especially in aqueous conditions. A recent theoretical investigation has been able to elucidate the reaction cascade as follows. Luminol is first deprotonated in basic conditions then oxidized to the anionic radical, which in turn has two paths available to give the key intermediate α-hydroxy- peroxide. After cyclization to the endoperoxide, the mono-anion will undergo decomposition ''without'' luminescence if the pH is too low (< 8.2) for a second deprotonation. The endoperoxide dianion, however, can give the retro-Diels–Alder product: 1,2-dioxane-3,6-dione dianion which, after ''chemiexcitation'' by two single-electron transfers (SET) gives 3-aminophthalate dianion in its first singlet excited state (S1). This highly unstable molecule relaxes to the ground state, emitting light of around 425 nm wavelength (purple-blue) in the process termed ''chemiluminescence''.

Use in criminal investigation

History

In 1928, German chemist H. O. Albrecht found that blood, among other substances, enhanced the luminescence of luminol in an alkaline solution of hydrogen peroxide. In 1936, Karl Gleu and Karl Pfannstiel confirmed this enhancement in the presence of haematin, a component of blood. In 1937, German forensic scientist Walter Specht made extensive studies of luminol's application to the detection of blood at crime scenes. In 1939, San Francisco pathologists Frederick Proescher and A. M. Moody made three important observations about luminol:
# although the test is presumptive, large areas of suspected material can be examined rapidly;
# dried and decomposed blood gave a stronger and more lasting reaction than fresh blood; and
# if the luminescence disappears, it may be reproduced by the application of a fresh luminol–hydrogen-peroxide solution; dried bloodstains may thus be made luminescent repeatedly.

Theory

Crime scene investigators use luminol to find traces of blood, even if someone has cleaned or removed it. The investigator sprays a solution of luminol and the oxidant. The iron in blood catalyses the luminescence. The amount of catalyst necessary to cause the reaction is very small relative to the amount of luminol, allowing detection of even trace amounts of blood. The blue glow lasts for about 30 seconds per application. Detecting the glow requires a fairly dark room. Any glow detected may be documented by a long-exposure photograph.

Drawbacks

Luminol's use in a crime scene investigation is somewhat hampered by the fact that it reacts to iron- and copper-containing compounds, bleaches, horseradish, fecal matter, and cigarette smoke residue. Application of luminol to a piece of evidence may prevent other tests from being performed on it; however, DNA has been successfully extracted from samples exposed to luminol.Technical note about ''Hemaglow''

Related molecules

* Luminol: 5-amino-2,3-dihydro-1,4 ; 3-amino-phthalhydrazide ; 1,4-phthalazinedione, 5-amino-2,3-dihydro ; CAS: 21-31-3br /> C₈H₇N₃O₂ – MW: 177.16
λ_abs (in 0.1 N NaOH) λ_max 1 : 347 nm & λ_max 2 : 300 nm; EC (at λ_max 1): 7650 L/mol × cm
λ_abs / λ_em (MeOH): 355/413 nm
* Luminol, sodium salt: sodium 3-amino-phthalhydrazide; CAS: 0666-12-0br /> C₈H₆N₃O₂Na – MW: 199.12
* Luminol hemihydrate: a hydrate of sodium 3-amino-phthalhydrazide; CAS: 06658-90-4br /> C₈H₆N₃O₂Na – MW: 217.16
* Luminol hydrochloride: 3-amino-phthalhydrazide hydrochloride; CAS: 4165-64-3br /> C₈H₇N₃O₂ · HCl MW: 213.62
* Isoluminol: 4-aminophthalhydrazide; CAS: 682-14-1br />C₈H₇N₃O₂ – MW: 117.16 (Xi)
* Isoluminol monohydrate: 4-aminophthalhydrazide monohydrate
C₈H₇N₃O₂ – MW: 195.15
* Isoluminol ABEI: 4-aminophthalhydrazide monohydrate; CAS: 6612-29-1

See also

* Fluorescein
* Diphenyl oxalate

References

External links

HowStuffWorks "How Luminol Works"

Luminol demonstration in Turin

{{Authority control

Aromatic amines
Chemical tests
Forensic chemicals
Hydrazides
Phthalazines
Lactams
Chemiluminescence