Iterative impedance is the input impedance of an infinite chain of identical networks. It is related to the
image impedance Image impedance is a concept used in electronic network design and analysis and most especially in filter design. The term ''image impedance'' applies to the impedance seen looking into a port of a network. Usually a two-port network is implied but ...
used in
filter design
Filter design is the process of designing a signal processing filter that satisfies a set of requirements, some of which may be conflicting. The purpose is to find a realization of the filter that meets each of the requirements to a sufficient ...
, but has a simpler, more straightforward definition.
Definition
Iterative
impedance is the input impedance of one port of a
two-port network
A two-port network (a kind of four-terminal network or quadripole) is an electrical network (circuit) or device with two ''pairs'' of terminals to connect to external circuits. Two terminals constitute a port if the currents applied to them satis ...
when the other port is connected to an infinite chain of identical networks. Equivalently, iterative impedance is that impedance that when connected to port 2 of a two-port network is equal to the impedance measured at port 1. This can be seen to be equivalent by considering the infinite chain of identical networks connected to port 2 in the first definition. If the original network is removed then port 1 of the second network will present the same iterative impedance as before since port 2 of the second network still has an infinite chain of networks connected to it. Thus the whole infinite chain can be replaced with a single
lumped impedance equal to the iterative impedance, which is the condition for the second definition.
In general, the iterative impedance of port 1 is not equal to the iterative impedance of port 2. They will be equal if the network is symmetrical, however
physically symmetry is not a necessary condition for the impedances to be equal.
Examples

A simple generic
L-circuit is shown in the diagram consisting of a series impedance ''Z'' and a shunt
admittance
In electrical engineering, admittance is a measure of how easily a circuit or device will allow a current to flow. It is defined as the reciprocal of impedance, analogous to how conductance & resistance are defined. The SI unit of admittan ...
''Y''. The iterative impedance of this network, ''Z''
IT, in terms of its output load (also ''Z''
IT) is given by,
:
and solving for ''Z''
IT,
:
Another example is an L-circuit with the components reversed, that is, with the shunt admittance coming first. The analysis of this circuit can be found immediately through
duality considerations of the previous example. The iterative admittance, ''Y''
IT, of this circuit is given by,
:
where,
:
The square root term in these expressions cause them to have two solutions. However, only solutions with a positive real part are physically meaningful since passive circuits cannot exhibit
negative resistance
In electronics, negative resistance (NR) is a property of some electrical circuits and devices in which an increase in voltage across the device's terminals results in a decrease in electric current through it.
This is in contrast to an ordi ...
. This will normally be the positive root.
Relationship to image impedance

Iterative impedance is a similar concept to
image impedance Image impedance is a concept used in electronic network design and analysis and most especially in filter design. The term ''image impedance'' applies to the impedance seen looking into a port of a network. Usually a two-port network is implied but ...
. Whereas an iterative impedance is formed by connecting port 2 of the first two-port network to port 1 of the next, an image impedance is formed by connecting port 2 of the first network to port 2 of the next. Port 1 of the second network is connected to port 1 of the third and so on, each subsequent network being reversed so that like ports always face each other.
It is thus no surprise that there is a relationship between iterative impedances and image impedances. In the L-circuit example for iterative impedance, the square-rooted term is equal to the image impedance of a half section. That is, an L-circuit where the component values are halved. Designating this half-section image impedance as ''Z''
IM we have for the L-circuit,
:
The diagrams show this result: an infinite chain of L-sections is identical to an infinite chain of alternately reversed half-sections except for the value of the initial series impedance.
For a symmetrical network, the iterative impedance and image impedance are identical and are the same at both ports. This impedance is sometimes called the network's
characteristic impedance
The characteristic impedance or surge impedance (usually written Z0) of a uniform transmission line is the ratio of the amplitudes of voltage and current of a single wave propagating along the line; that is, a wave travelling in one direction ...
, a term usually reserved for
transmission lines. The model for a transmission line is an infinite chain of L-sections with infinitesimally small components. A transmission line characteristic impedance is thus the
limiting case of a
ladder network
Electronic filter topology defines electronic filter circuits without taking note of the values of the components used but only the manner in which those components are connected.
Filter design characterises filter circuits primarily by their t ...
iterative impedance.
[Montgomery ''et al.'', pp. 112-113]
References
Bibliography
* Bakshi, U. A.; Bakshi, A. V., ''Electric Circuits'',
* Bird, John, ''Electrical Circuit Theory and Technology'', Routledge, 2013 .
* Iyer,T. S. K. V, ''Circuit Theory'', Tata McGraw-Hill Education, 1985 .
* Montgomery, Carol Gray; Dicke, Robert Henry; Purcell, Edward M., ''Principles of Microwave Circuits'', IEE, 1948 .
* Walton, Alan Keith, ''Network Analysis and Practice'', Cambridge University Press, 1987 {{ISBN, 052131903X.
Analog circuits
Filter theory
Electronic design