ISO 25178: Geometrical Product Specifications (GPS) – Surface texture: areal is an

International Organization for Standardization The International Organization for Standardization (ISO ; ; ) is an independent, non-governmental, international standard development organization composed of representatives from the national standards organizations of member countries. M ...

collection of international standards relating to the analysis of 3D areal

surface texture Surface finish, also known as surface texture or surface topography, is the nature of a surface as defined by the three characteristics of lay, surface roughness, and waviness.. It comprises the small, local deviations of a surface from the pe ...

Structure of the standard

Documents constituting the standard: * Part 1: Indication of surface texture * Part 2: Terms, definitions and surface texture parameters * Part 3: Specification operators * Part 6: Classification of methods for measuring surface texture * Part 70: Material measures * Part 71: Software measurement standards * Part 72: XML file format x3p * Part 600: Metrological characteristics for areal-topography measuring methods * Part 601: Nominal characteristics of contact (stylus) instruments * Part 602: Nominal characteristics of non-contact (confocal chromatic probe) instruments * Part 603: Nominal characteristics of non-contact (phase-shifting interferometric microscopy) instruments * Part 604: Nominal characteristics of non-contact ( coherence scanning interferometry) instruments * Part 605: Nominal characteristics of non-contact (point autofocus probe) instruments * Part 606: Nominal characteristics of non-contact (

focus variation Focus variation is a method used to sharpen images and to measure surface irregularities by means of optics with limited depth of field. Algorithm The algorithm works as follows: # At first images with difference focus are captured. This is done by ...

) instruments * Part 607: Nominal characteristics of non-contact (

confocal microscopy Confocal microscopy, most frequently confocal laser scanning microscopy (CLSM) or laser scanning confocal microscopy (LSCM), is an optical imaging technique for increasing optical resolution and contrast (vision), contrast of a micrograph by me ...

) instruments * Part 700: Calibration of surface texture measuring instruments WIP* Part 701: Calibration and measurement standards for contact (stylus) instruments Other documents might be proposed in the future but the structure is now almost defined. Part 600 will replace the common part found in all other parts. When revised, parts 60x will be reduced to only contain descriptions specific to the instrument technology.

New features

It is the first international standard taking into account the specification and measurement of 3D surface texture. In particular, the standard defines 3D surface texture parameters and the associated specification operators. It also describes the applicable measurement technologies,

calibration In measurement technology and metrology, calibration is the comparison of measurement values delivered by a device under test with those of a calibration standard of known accuracy. Such a standard could be another measurement device of known ...

methods, together with the physical calibration standards and calibration software that are required. A major new feature incorporated into the standard is coverage of non-contact measurement methods, already commonly used by industry, but up until now lacking a standard to support quality audits within the framework of

ISO 9000 The ISO 9000 family is a set of international standards for Quality (business), quality management systems. It was developed in March 1987 by International Organization for Standardization. The goal of these standards is to help organizations en ...

. For the first time, the standard brings 3D surface

metrology Metrology is the scientific study of measurement. It establishes a common understanding of Unit of measurement, units, crucial in linking human activities. Modern metrology has its roots in the French Revolution's political motivation to stan ...

methods into the official domain, following 2D profilometric methods that have been subject to standards for over 30 years. The same thing applies to measurement technologies that are not restricted to contact measurement (with a diamond point

stylus A stylus is a writing utensil or tool for scribing or marking into softer materials. Different styluses were used to write in cuneiform by pressing into wet clay, and to scribe or carve into a wax tablet. Very hard styluses are also used to En ...

), but can also be optical, such as chromatic confocal gauges and interferometric microscopes.

New definitions

The ISO 25178 standard is considered by TC213 as first and foremost providing a redefinition of the foundations of surface texture, based upon the principle that nature is intrinsically 3D. It is anticipated that future work will extend these new concepts into the domain of 2D profilometric surface texture analysis, requiring a total revision of all current surface texture standards ( ISO 4287, ISO 4288, ISO 1302, ISO 11562, ISO 12085, ISO 13565, etc.) A new vocabulary is imposed: * S filter: filter eliminating the smallest scale elements from the surface (or of the shortest wavelength for a linear filter) * L filter: filter eliminating the largest scale elements from the surface (or of the longest wavelength for a linear filter) * F operator: operator suppressing nominal form. * Primary surface: surface obtained after S filtering. * S-F surface: surface obtained after applying an F operator to the primary surface. * S-L surface: surface obtained after applying an L filter to the S-F surface. * Nesting index: index corresponding to the cut-off wavelength of a linear filter, or to the scale of the structuring element of a morphological filter. Under 25178, industry-specific taxonomies such as roughness vs waviness are replaced by the more general concept of "scale limited surface" and "cut-off" by "nesting index". The new available filters are described in the series of technical specifications included in ISO 16610. These filters include: the Gaussian filter, the spline filter, robust filters, morphological filters, wavelet filters, cascading filters, etc.

Parameters

Generalities

3D areal surface texture parameters are written with the capital letter S (or V) followed by a suffix of one or two small letters. They are calculated on the entire surface and no more by averaging estimations calculated on a number of base lengths, as is the case for 2D parameters. In contrast with 2D naming conventions, the name of a 3D parameter does not reflect the filtering context. For example, ''Sa'' always appears regardless of the surface, whereas in 2D there is ''Pa'', ''Ra'' or ''Wa'' depending on whether the profile is a primary, roughness or waviness profile.

Height parameters

These parameters involve only the statistical distribution of height values along the z axis.

Spatial parameters

These parameters involve the spatial periodicity of the data, specifically its direction.

Hybrid parameters

These parameters relate to the spatial shape of the data.

Functions and related parameters

These parameters are calculated from the material ratio curve ( Abbott-Firestone curve).

Parameters related to segmentation

These ''feature parameters'' are derived from a segmentation of the surface into motifs (dales and hills). Segmentation is carried out using a watershed method.

Software

A consortium of several companies started to work in 2008 on a free implementation of 3D surface texture parameters. The consortium, called OpenGP

later focused its efforts on an XML file format (X3P) that was published under the ISO standard ISO 25178-72. Several commercial packages provide part or all of the parameters defined in ISO 25178, such as MountainsMap from Digital Surf, SPIP from Image Metrolog

TrueMap 6 from TrueGag

as well as the open source Gwyddion.

Instruments

Part 6 of the standard divides the usable technologies for 3D surface texture measurement into three families: # Topography, Topographical instruments: contact and non-contact 3D profilometers, interferometric and confocal microscopes, structured light projectors, stereoscopic microscopes, etc. # Profilometric instruments: contact and non-contact 2D profilometers, line triangulation lasers, etc. # Instruments functioning by integration:

pneumatic Pneumatics (from Greek 'wind, breath') is the use of gas or pressurized air in mechanical systems. Pneumatic systems used in Industrial sector, industry are commonly powered by compressed air or compressed inert gases. A centrally located a ...

measurement, capacitive, by optical diffusion, etc. and defines each of these technologies. Next, the standard explores a number of these technologies in detail and dedicates two documents to each of them: * Part 6xx: nominal characteristics of the instrument * Part 7xx: calibration of the instrument

Contact profilometer

Parts 601 and 701 describe the contact profilometer, using a diamond point to measure the surface with the assistance of a lateral scanning device.

Chromatic confocal gauge

Part 602 describes this type of non-contact profilometer, incorporating a single point white light chromatic confocal sensor. The operating principle is based upon the chromatic dispersion of the white light source along the optical axis, via a confocal device, and the detection of the wavelength that is focused on the surface by a

spectrometer A spectrometer () is a scientific instrument used to separate and measure Spectrum, spectral components of a physical phenomenon. Spectrometer is a broad term often used to describe instruments that measure a continuous variable of a phenomeno ...

Coherence scanning interferometry

Part 604 describes a class of optical surface measurement methods wherein the localization of interference fringes during a scan of optical path length provides a means to determine surface characteristics such as topography, transparent film structure, and optical properties. The technique encompasses instruments that use spectrally broadband, visible sources (white light) to achieve interference fringe localization). CSI uses either fringe localization alone or in combination with interference fringe phase.

Focus variation

Part 606 describes this type of non-contact areal based method. The operating principle is based on a microscope optics with limited depth of field and a CCD camera. By scanning in vertical direction several images with different focus are gathered. This data is then used to calculate a surface data set for roughness measurement.

References

ISO 25178 on the ISO Web site

''New 3D parameters and filtration techniques for surface metrology'', François Blateyron, Quality Magazine White Paper
* ISO/TS 16610-1 : Geometrical Product Specifications (GPS): Filtration – Part 1: Overview and basic concepts * ISO/TS 14406 : Geometrical Product Specifications (GPS): Extraction * Blateyron, F. (2013). The Areal Field Parameters. Characterisation of Areal Surface Texture. R. Leach, Springer Berlin Heidelberg: 15-43. * de Groot, P. J. (2014). Progress in the specification of optical instruments for the measurement of surface form and texture. Proc. SPIE. 9110: 91100M-91101-91112. * Leach, R. K., Ed. (2013). Characterisation of Areal Surface Texture. Heidelberg, Springer {{DEFAULTSORT:Iso 25178 #25178 Metrology Surfaces Geometric measurement