Fluorescent-lamp Formats

Since their introduction as a commercial product in 1939, many different types of fluorescent lamp have been introduced. Systematic nomenclature identifies mass-market lamps as to overall shape, power rating, length, color, and other electrical and illuminating characteristics.

Tube designations

In the United States and Canada, lamps are typically identified by a code such as FxxTyy, where F is for fluorescent, and the first number (xx) indicates either the power in watts for bi-pin lamps, length in inches for single-pin and high-output lamps, and for circular bulbs, the diameter of the circular bulb. The T indicates that the shape of the bulb is tubular, and the last number (yy) is the diameter in eighths of an inch (sometimes in millimeters, rounded up to the nearest millimeter). Typical diameters are T12 or T38 () for larger, often less efficient lamps, T8 or T26 () for smaller and often energy-saving lamps, and T5 or T16 () for very small lamps, which may even operate from a battery-powered device.

For T2–T12 and T17, the number indicates the tube diameter in inches, e.g. T2 →  in and T17 →  in. Whereas for T16 and T26–T38, the number indicates the approximate tube diameter in millimeters.

Reflectors

Some lamps have an internal opaque reflector. Coverage of the reflector ranges from 120° to 310° of the lamp's circumference.

Reflector lamps are used when light is only desired to be emitted in a single direction, or when an application requires the maximum amount of light. For example, these lamps can be used in tanning beds or in backlighting electronic displays. An internal reflector is more efficient than standard external reflectors. Another example is color matched aperture lights (with about 30° of opening) used in the food industry for robotic quality control inspection of cooked goods.

Aperture lamps have a clear break in the phosphor coating, typically of 30°, to concentrate light in one direction and provide higher brightness in the beam than can be achieved by uniform phosphor coatings. Aperture lamps include reflectors over the non-aperture area. Aperture lamps were commonly used in photocopiers in the 1960s and 1970s where a bank of fixed tubes was arranged to light up the image to be copied, but are rarely found nowadays. Aperture lamps can produce a concentrated beam of light suitable for edge-lit signs.

Single-pin lamps

Single-pin lamps (Also generically called "Slimline" in the United States) operate on an instant start ballast in the United States and Canada or on a series choke without a starter in 220-240V countries.

High-output/very high output lamps

High-output lamps are brighter and are driven at a higher electric current. They have a recessed double contact (R17d) base on each end, rather than a standard bi-pin base, which prevents them from being installed into the wrong fixture. Since about the early to mid-1950s to today, General Electric has developed and improved the ''Power Groove'' lamp. These lamps are recognizable by their large diameter () and grooved tube shape.

Colors

Colors using a halophosphate formulation are usually indicated by WW for warm white, W for (neutral) white, CW for cool white, and D for the bluish daylight white.

Philips and Osram use numeric color codes for tri-phosphor and multi-phosphor colors. The first digit indicates the color rendering index (CRI) of the lamp. If the first digit on a lamp says 8, then the CRI of that lamp will be approximately 85. The last two digits indicate the color temperature of the lamp in kelvins (K). For example, if the last two digits on a lamp say 41, that lamp's color temperature will be 4100 K, which is a common tri-phosphor cool white fluorescent lamp.

BL is used for ultraviolet lamps commonly used in bug zappers. BLB is used for blacklight-blue lamps employing a Wood's glass envelope to filter out most visible light, commonly used in nightclubs. Other non-standard designations apply for plant lights or grow lights.

Common tube ratings

This section lists the more common tube ratings for general lighting. Many more tube ratings exist, often country-specific. The ''Nominal Length'' may not exactly match any measured dimension of the tube. For some tube sizes, the nominal length (in feet) is the required spacing between centers of the lighting fixtures to create a continuous run, so the tubes are a little shorter than the nominal length.

European energy-saving tubes

In the 1970s, Thorn Lighting introduced an energy-saving 8 ft retrofit tube in Europe. Designed to run on the existing 125 W (240 V) series ballast but with a different gas fill and operating voltage, the tube operated at only 100 W. Increased efficiency meant that the tube produced only 9% lumen reduction for a 20% power reduction. This first energy-saving tube design remains a T12 tube even today. However, follow-on retrofit replacements for all the other original T12 tubes were T8, which helped with creating the required electrical characteristics and saving on the then new (and more expensive) polyphosphor/triphosphor coatings, and these were even more efficient. Note that because these tubes were all designed as retrofit tubes to be fitted in T12 fittings running on series ballasts on 220–240 V supplies, they could not be used in 120 V mains countries with inherently different control gear designs.

Around 1980 (in the UK, at least), some new fluorescent fittings were designed to take only the newer, retrofit tubes (the lamp holders are designed not to take T12 tubes, except for 8 ft length). The earlier T12 halophosphate tubes still remained available as spares until 2012. They fit in older fittings and some modern fittings that employ twist lock lamp holders, even though the modern fittings were not electrically designed for them.

US energy-saving tubes

In the 1970s, 34-watt energy-saving F40T12 fluorescent lamps were intoroduced in the United States. In the 1980s, T8 32-watt lamps were introduced, but unlike the T8 tubes introduced in Europe, these T8s are not retrofits and require new matching ballasts to drive them. These ballasts were originally magnetic, but most today are electronic. The energy-saving T12 lamps are made to operate on ballasts designed for 40-watt F40T12 lamps, though some F40T12 ballasts are not be designed to operate these lamps, and can overheat if energy-saving lamps are used. Running an energy-saving T8 tube with a ballast for T12 will reduce lamp life and can increase energy consumption. Conversely, a T12 tube on a T8 ballast will usually draw too much power and so may burn out the ballast, unless it is within the range that particular ballast can compensate for. The tube type should always match the markings on the light fixture.

T5 tubes

In the 1990s, longer T5 tubes were designed in Europe (making it to North America in the 2000s), in addition to the shorter ones (mentioned above) already in use worldwide. Like the European modular furniture, display cabinets, ceiling tile grids, etc. they were designed for, these are based on multiples of the "metric foot" instead of the imperial foot, but are all shorter to allow space for the lampholder connections within the 300 mm modular units, and for much easier insertion into and removal from troffer lights within a grid.

The T5 diameter is nearly 40% smaller than T8 lamps and almost 60% smaller than T12 lamps. T5 lamps have a G5 base (bi-pin with 5 mm spacing), even for high-output (HO and VHO) tubes.Lighting Research Center, "T5 Fluorescent Systems"

accessed 11-30-2009.

Electrical parameters of linear tubes

See also

*Compact fluorescent lamp
*List of light sources
*Fluorescent lamp recycling
*T5 retrofit conversion

References

{{DEFAULTSORT:Fluorescent-lamp formats
Gas discharge lamps

de:Leuchtstofflampe#Standardisierte Baugrößen