DBm

dBm or dB_mW (decibel-milliwatts) is a unit of power level expressed using a logarithmic decibel (dB) scale respective to one milliwatt (mW). It is commonly used by radio, microwave and fiber-optical communication technicians & engineers to measure the power of system transmissions on a log scale, which can express both very large and very small values in a short form. dBW is a similar unit measured relative to one watt (1,000 mW), rather than a milliwatt.

The decibel (dB) is a dimensionless unit, used for quantifying the ratio between two values, such as signal-to-noise ratio. The dBm is also dimensionless, but since it compares to a fixed reference value, the dBm rating is an absolute one.

The dBm is not a part of the International System of Units (SI) and therefore is discouraged from use in documents or systems that adhere to SI units. (The corresponding SI unit is the watt.) However, the unit decibel (dB), without the 'm' suffix, is permitted for relative quantities, but not accepted for use directly alongside SI units. Ten decibel-milliwatts may be written 10 dB (1 mW) in SI.

In audio and telephony, dBm is typically referenced relative to the 600-ohm impedance commonly used in telephone voice networks, while in radio-frequency work dBm is typically referenced relative to a 50-ohm impedance.

Unit conversions

A power level of 0 dBm corresponds to a power of 1 milliwatt. A 10 dB increase in level is equivalent to a ten-fold increase in power. Therefore, a 20 dB increase in level is equivalent to a 100-fold increase in power. A 3 dB increase in level is approximately equivalent to doubling the power, which means that a level of 3 dBm corresponds roughly to a power of 2 mW. Similarly, for each 3 dB decrease in level, the power is reduced by about one half, making −3 dBm correspond to a power of about 0.5 mW.

To express an arbitrary power in mW as in dBm, the following expression may be used:
$\begin x &= 10 \log_ \frac \end$
Conversely, to express an arbitrary power level in dBm, as in mW:
$\begin P &= 1~\text \cdot 10^ \end$

Table of examples

Below is a table summarizing useful cases:

Standards

The signal intensity (power per unit area) can be converted to received signal power by multiplying by the square of the wavelength and dividing by 4 (see Free-space path loss).

In United States Department of Defense practice, unweighted measurement is normally understood, applicable to a certain bandwidth, which must be stated or implied.

In European practice, psophometric weighting may be, as indicated by context, equivalent to dBm0p, which is preferred.

In audio, 0 dBm often corresponds to approximately 0.775 volts, since 0.775 V dissipates 1 mW in a 600 Ω load. The corresponding voltage level is 0 dBu, without the 600 Ω restriction. Conversely, for RF situations with a 50 Ω load, 0 dBm corresponds to approximately 0.224 volts, since 0.224 V dissipates 1 mW in a 50 Ω load.

In general the relationship between the power level in dBm and the voltage in volts across a load of resistance (typically used to terminate a transmission line with impedance ) is:
$\begin V &= \sqrt\,. \end$

Expression in dBm is typically used for optical and electrical power measurements, not for other types of power (such as thermal). A listing by power levels in watts is available that includes a variety of examples not necessarily related to electrical or optical power.

The dBm was first proposed as an industry standard in 1940.

See also

* Decibel watt
* dBm0

References

External links

The dBm calculator for impedance matching

Convert dBm to watts

{{DEFAULTSORT:Dbm
Units of power
Radio frequency propagation
Logarithmic scales of measurement