 |
Thread Angle
The thread angle of a screw is the included angle between the thread flanks, measured in a plane containing the thread axis.. This is a defining factor for the shape of a screw thread A screw thread, often shortened to thread, is a helical structure used to convert between rotational and linear movement or force. A screw thread is a ridge wrapped around a cylinder or cone in the form of a helix, with the former being called .... Standard values include: References Notes Bibliography *. * {{MachinerysHandbook25e Screws Metalworking terminology Threading (manufacturing) ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
|
NPT Dimensions
NPT may refer to: Codes Newport State Airport, Middletown, Rhode Island, US, IATA code Law * Nuclear Non-Proliferation Treaty, since 1970 * Neighbourhood Policing Team, UK Organizations * National Philanthropic Trust, offering donor-advised funds Places * Northville-Placid Trail, New York, US Technology * National pipe thread, US standards * Nested Page Tables, later Rapid Virtualization Indexing, an AMD technology * Nissan NPT-90, a racing car * Non-pneumatic tire or airless tire * IPv6-to-IPv6 Network Prefix Translation (NPTv6) Miscellaneous * Nepal Standard Time Nepal Standard Time (NPT) is the time zone for Nepal. With a time offset from Coordinated Universal Time (UTC) of UTC+05:45 all over Nepal, it is one of only three time zones with a 45-minute offset from UTC.The others are Chatham Island Stand ... * NpT ensemble or isothermal–isobaric ensemble Near Patient Testing. Clinical patient testing done in Primary care, under a shared care agre ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
|
 |
Stahlpanzerrohrgewinde
The Stahlpanzerrohrgewinde (, "steel conduit thread") standard for screw threads, more often called by the shortened Panzergewinde (), was a technical standard created in Germany and subsequently used in Switzerland, Austria, and other neighboring European countries. It has been retracted. The thread is used to join pieces of electrical conduit and cable glands. Alternative stylings of the German name are ''Stahl-Panzer-Rohr-Gewinde'', an abbreviated form ''StaPa-Rohr-Gewinde'', and the acronym ''PG''. Overview The standard, codified by the ''Deutsches Institut für Normung'' (DIN, German Institute for Standardization), is DIN 40430. ''Panzergewinde'' sizes are named with the prefix ''PG'' plus a nominal number which approximately corresponds to the maximum cable diameter (in millimeters) that can be passed through the conduit. Because the walls of the conduit are usually relatively thin, the thread depth is limited. Thus a thread angle of 80° is used. The ''Verband der El ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
|
Panzergewinde
The Stahlpanzerrohrgewinde (, "steel conduit thread") standard for screw threads, more often called by the shortened Panzergewinde (), was a technical standard created in Germany and subsequently used in Switzerland, Austria, and other neighboring European countries. It has been retracted. The thread is used to join pieces of electrical conduit and cable glands. Alternative stylings of the German name are ''Stahl-Panzer-Rohr-Gewinde'', an abbreviated form ''StaPa-Rohr-Gewinde'', and the acronym ''PG''. Overview The standard, codified by the ''Deutsches Institut für Normung'' (DIN, German Institute for Standardization), is DIN 40430. ''Panzergewinde'' sizes are named with the prefix ''PG'' plus a nominal number which approximately corresponds to the maximum cable diameter (in millimeters) that can be passed through the conduit. Because the walls of the conduit are usually relatively thin, the thread depth is limited. Thus a thread angle of 80° is used. The '' Verband de ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
|
 |
Square Thread
The square thread form is a common screw thread profile, used in high load applications such as leadscrews and jackscrews. It gets its name from the square cross-section of the thread.Bhandari, p. 203. It is the lowest friction and most efficient thread form, but it is difficult to fabricate. Advantages & disadvantages The greatest advantage of square threads is that they have a much higher intrinsic efficiency than trapezoidal threads (Acme or metric trapezoidal). Due to the lack of a thread angle there is no radial pressure, or bursting pressure, on the nut. This also increases the nut life. The greatest disadvantage is the difficulty in machining such a thread. The single-point cutting tools or taps and dies used to cut the thread cannot have efficient rake and relief angles (because of the square form), which makes the cutting slow and difficult. Square threads also cannot carry as much load as a trapezoidal thread, because the root of the square thread is smaller. Also ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
 |
Buttress Thread
Buttress thread forms, also known as sawtooth thread forms or breech-lock thread forms. are screw thread profiles with an asymmetric shape, having one square face and the other slanted. They are most commonly used for leadscrews where the load is principally applied in one direction. The asymmetric thread form allows the thread to have low friction and withstand greater loads than other forms in one direction, but at the cost of higher friction and inferior load bearing in the opposite direction. They are typically easier to manufacture than square thread forms but offer higher load capacity than equivalently sized Trapezoidal thread forms. Buttress thread characteristics The buttress thread form is designed to handle axial thrust applied principally in one direction. The load-bearing thread face is perpendicular or at a slight slant (usually no greater than 7°) to the screw axis. The trailing face is slanted, often at 45°. The resulting thread form has the same low fricti ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
 |
Buttress Thread Form A buttress is an architectural structure built against or projecting from a wall which serves to support or reinforce the wall. Buttresses are fairly common on more ancient buildings, as a means of providing support to act against the lateral (sideways) forces arising out of inadequately braced roof structures. The term ''counterfort'' can be synonymous with buttress and is often used when referring to dams, retaining walls and other structures holding back earth. Early examples of buttresses are found on the Eanna Temple (ancient Uruk), dating to as early as the |