|
Fiat 600
The Fiat 600 ( it, Seicento, ) is a rear-engine, water-cooled city car, manufactured and marketed by Fiat from 1955 to 1969 — offered in two-door fastback sedan and four-door Multipla mini MPV body styles. Measuring only long, its all-new design was the first unibody and rear-engined Fiat, and was priced the equivalent of about €6,700 or US$7300 in today's money (590,000 lire then). The total number produced from 1955 to 1969 at the Mirafiori plant in Turin was 2,695,197. The 1955 Fiat 600 formed the blueprint for the 2nd generation "Nuova" (New) 500, launched two years later – which was even smaller, at and, although rounder, largely copied the 600s layout and shape. Later, the 600 also formed the platform for the larger 850 saloon, launched in 1964, which coexisted with the 600 in Fiats line-up for five years, until the 600 was cancelled. During the 1950s, '60s, '70s and '80s, many units were built in countries such as Spain (as SEAT 600), where it became th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fiat Automobiles
Fiat Automobiles S.p.A. (, , ; originally FIAT, it, Fabbrica Italiana Automobili di Torino, lit=Italian Automobiles Factory of Turin) is an Italian automobile manufacturer, formerly part of Fiat Chrysler Automobiles, and since 2021 a subsidiary of Stellantis through its Italian division Stellantis Italy. Fiat Automobiles was formed in January 2007 when Fiat S.p.A. reorganized its automobile business, and traces its history back to 1899 when the first Fiat automobile, the Fiat 4 HP, was produced. Fiat Automobiles is the largest automobile manufacturer in Italy. During its more than century-long history, it remained the largest automobile manufacturer in Europe and the third in the world after General Motors and Ford for over 20 years, until the car industry crisis in the late 1980s. In 2013, Fiat S.p.A. was the second largest European automaker by volumes produced and the seventh in the world, while FCA was the world's eighth-largest automaker. In 1970, Fiat Automobiles em ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rear-engine, Rear-wheel-drive Layout
In automotive design, an RR, or rear-engine, rear-wheel-drive layout places both the engine and drive wheels at the rear of the vehicle. In contrast to the RMR layout, the center of mass of the engine is between the rear axle and the rear bumper. Although very common in transit buses and coaches due to the elimination of the drive shaft with low-floor buses, this layout has become increasingly rare in passenger cars. Overview Most of the traits of the RR configuration are shared with the mid-engine rear-wheel-drive, or MR. Placing the engine near the driven rear wheels allows for a physically smaller, lighter, less complex, and more efficient drivetrain, since there is no need for a driveshaft, and the differential can be integrated with the transmission, commonly referred to as a transaxle. The front-engine front-wheel-drive layout also has this advantage. Since the engine is typically the heaviest component of the car, putting it near the rear axle usually results i ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rear Engine
In automobile design, a rear-engine design layout places the engine at the rear of the vehicle. The center of gravity of the engine itself is behind the rear axle. This is not to be confused with the center of gravity of the whole vehicle, as an imbalance of such proportions would make it impossible to keep the front wheels on the ground. Rear-engined vehicles almost always have a rear-wheel drive car layout, but some are four wheel drive. This layout has the following features: *Packaging: since there is no need for a transmission tunnel, the floor can be flat. *Rear traction: having the engine located over the driven wheels increases downward pressure, which is helpful for grip on loose surfaces, although can be prone to oversteer. *Simplicity of manufacture: the engine is near the driven wheels, and the transmission can be merged with the differential to save space. This layout was once popular in small, inexpensive cars and light commercial vehicles. Today most car makers hav ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Unibody
A vehicle frame, also historically known as its ''chassis'', is the main supporting structure of a motor vehicle to which all other components are attached, comparable to the skeleton of an organism. Until the 1930s, virtually every car had a structural frame separate from its body. This construction design is known as '' body-on-frame''. By the 1960s, unibody construction in passenger cars had become common, and the trend to unibody for passenger cars continued over the ensuing decades. Nearly all trucks, buses, and most pickups continue to use a separate frame as their chassis. Functions The main functions of a frame in a motor vehicle are: # To support the vehicle's mechanical components and body # To deal with static and dynamic loads, without undue deflection or distortion. :These include: ::*Weight of the body, passengers, and cargo loads. ::*Vertical and torsional twisting transmitted by going over uneven surfaces. ::*Transverse lateral forces caused by road condi ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Mini MPV
Mini MPV— an abbreviation for mini multi-purpose vehicle— is a vehicle size class for the smallest size of minivans/MPVs. The mini MPV size class sits below the compact MPV size class and the vehicles are often built on the platforms of B-segment hatchback models. By the European definition, the mini MPV commonly consists of cars with two rows of seats, while in Asia mini MPVs with three rows are common. Sliding doors are sometimes also fitted to mini MPVs. Mini MPV are also called tall-hatchback or small MPV. __TOC__ Characteristics Europe Mini MPVs are typically based on the platform of a B-segment (supermini/subcompact) hatchback, with a raised roof and five-door body. The raised roof allows for higher H-point seating and easy passenger access compared with traditional hatchbacks. Often the rear seats can recline, slide, tumble, fold flat or easily be removed, allowing users to reconfigure the rear passenger and cargo volumes for each journey. The segment was cr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
City Car
The A-segment is the 1st category in the passenger car classification system defined by the European Commission. It is used for city cars, the smallest category of passenger cars defined. A-segment sales represent approx. 7-8% of the market in 2010s. It is approximately equivalent to the kei car class in Japan. Definition As of 2021 A-segment category size span from approximately to (photo comparison of new city cars of all brands sorted by length): Characteristics Body styles for A-segment cars in Europe are always hatchbacks. But as crossovers gain popularity, new models may shift to resemble crossovers. Such examples are the Suzuki Ignis and the Toyota Aygo X. Other body styles such as sedans are not present in this segment because these shapes largely prove impractical at typical A-segment dimensions. History As of 2017, 2018, 2019 and 2020, A-segment sales account for 8.1%, 8%, 7.7% and 6.8% market share in Europe respectively. Current models I ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fiat 127
The Fiat 127 is a supermini car produced by Italian car manufacturer FIAT from 1971 to 1983. It was introduced in 1971 as the replacement for the Fiat 850. Production of the 127 in Italy ended in 1983 following the introduction of its replacement, the Fiat Uno, although the nameplate continued to be used on cars imported from Brazil. Series 1 Developed towards the end of the 1960s, the Fiat 127 was launched as a two-door saloon in April 1971. A three-door hatchback, using an identical body profile but with a full-depth rear door and folding rear seat, was launched in March of the following year; this would prove to be the most popular version of the 127. This was Fiat's first supermini-sized hatchback. The 127 featured a state-of-the-art transverse-engine/front-wheel-drive layout, with the transmission mounted on the end of the engine. Both design ideas had been fully vetted by Fiat, using its Autobianchi subsidiary 1964 Primula, 1969 A112 and A111 — precisely becaus ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fiat 500 "Topolino"
The Fiat 500, commonly known as "Topolino", is an Italian city car produced and manufactured by Fiat from 1936 to 1955. The name ''Topolino'' () is Italian and translates literally as "little mouse", but is also the Italian name for Mickey Mouse. History The Topolino was one of the smallest cars in the world at the time of its production. Launched in 1936, three models were produced until 1955, all with only minor mechanical and cosmetic changes. It was equipped with a 569 cc four-cylinder, side-valve, water-cooled engine mounted in front of the front axle (later an overhead valve motor), and so was a full-scale car rather than a cyclecar. The radiator was located behind the engine which made possible a lowered aerodynamic nose profile at a time when competitors had a flat, nearly vertical grille. The shape of the car's front allowed exceptional forward visibility. Rear suspension initially used quarter-elliptic rear springs, but buyers frequently squeezed four or five ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Manual Transmission
A manual transmission (MT), also known as manual gearbox, standard transmission (in Canada, the United Kingdom, and the United States), or stick shift (in the United States), is a multi-speed motor vehicle transmission system, where gear changes require the driver to manually select the gears by operating a gear stick and clutch (which is usually a foot pedal for cars or a hand lever for motorcycles). Early automobiles used ''sliding-mesh'' manual transmissions with up to three forward gear ratios. Since the 1950s, ''constant-mesh'' manual transmissions have become increasingly commonplace and the number of forward ratios has increased to 5-speed and 6-speed manual transmissions for current vehicles. The alternative to a manual transmission is an automatic transmission; common types of automatic transmissions are the hydraulic automatic transmission (AT), and the continuously variable transmission (CVT), whereas the automated manual transmission (AMT) and dual-clutch tran ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Inline-four Engine
A straight-four engine (also called an inline-four) is a four-cylinder Reciprocating engine, piston engine where cylinders are arranged in a line along a common crankshaft. The vast majority of automotive four-cylinder engines use a straight-four layout (with the exceptions of the flat-four engines produced by Subaru and Porsche) and the layout is also very common in motorcycles and other machinery. Therefore the term "four-cylinder engine" is usually synonymous with straight-four engines. When a straight-four engine is installed at an inclined angle (instead of with the cylinders oriented vertically), it is sometimes called a Slant-4 engine, slant-four. Between 2005 and 2008, the proportion of new vehicles sold in the United States with four-cylinder engines rose from 30% to 47%. By the 2020 model year, the share for light-duty vehicles had risen to 59%. Design A four-stroke straight-four engine always has a cylinder on its power stroke, unlike engines with fewer cylinders ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Overhead Valve
An overhead valve (OHV) engine, sometimes called a ''pushrod engine'', is a piston engine whose valves are located in the cylinder head above the combustion chamber. This contrasts with earlier flathead engines, where the valves were located below the combustion chamber in the engine block. Although an overhead camshaft (OHC) engine also has overhead valves, the common usage of the term "overhead valve engine" is limited to engines where the camshaft is located in the engine block. In these traditional OHV engines, the motion of the camshaft is transferred using pushrods (hence the term "pushrod engine") and rocker arms to operate the valves at the top of the engine. Some early intake-over-exhaust engines used a hybrid design combining elements of both side-valves and overhead valves. History Predecessors The first internal combustion engines were based on steam engines and therefore used slide valves. This was the case for the first Otto engine, which was first ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
