|
3-state Buffers
In digital electronics, a tri-state or three-state buffer is a type of digital buffer that has three stable states: a high voltage output state (logical 1), a low output state (logical 0), and a high-impedance (Hi-Z) state. In the Hi-Z state, the output of the buffer is effectively disconnected from the subsequent circuit. Tri-state buffers are commonly used in bus-based systems where multiple devices are connected to the same shared bus, because the Hi-Z state allows other devices to drive the bus without interference from the tri-state buffer. For example, in a computer system, multiple devices such as the CPU, memory, and peripherals may be connected to the same data bus. To ensure that only one device can transmit data on the bus at a time, each device is equipped with a tri-state buffer. When a device wants to transmit data, it activates its tri-state buffer, which connects its output to the bus and allows it to transmit data. When the transmission is complete, the device ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Digital Electronics
Digital electronics is a field of electronics involving the study of digital signals and the engineering of devices that use or produce them. It deals with the relationship between Binary number, binary inputs and outputs by passing electrical signals through Logic gate, logical gates, Resistor, resistors, Capacitor, capacitors, Amplifier, amplifiers, and other Electronic component, electrical components. The field of digital electronics is in contrast to analog electronics which work primarily with analog signals (signals with varying degrees of intensity as opposed to on/off two state binary signals). Despite the name, digital electronics designs include important analog design considerations. Large assemblies of logic gates, used to represent more complex ideas, are often packaged into integrated circuits. Complex devices may have simple electronic representations of Boolean logic#Digital electronic circuit design, Boolean logic functions. History The binary number system was ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Logic Level
In digital circuits, a logic level is one of a finite number of states that a digital signal can inhabit. Logic levels are usually represented by the voltage difference between the signal and ground, although other standards exist. The range of voltage levels that represent each state depends on the logic family being used. A '' logic-level shifter'' can be used to allow compatibility between different circuits. 2-level logic In binary logic the two levels are logical high and logical low, which generally correspond to binary numbers 1 and 0 respectively or truth values ''true'' and ''false'' respectively. Signals with one of these two levels can be used in Boolean algebra for digital circuit design or analysis. Active state The use of either the higher or the lower voltage level to represent either logic state is arbitrary. The two options are active high (''positive logic'') and active low (''negative logic''). Active-high and active-low states can be mixed at will: for ex ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Leakage (electronics)
In electronics, leakage is the gradual transfer of electrical energy across a boundary normally viewed as insulating, such as the spontaneous discharge of a charged capacitor, magnetic coupling of a transformer with other components, or flow of current across a transistor in the "off" state or a reverse-polarized diode. In capacitors Gradual loss of energy from a charged capacitor is primarily caused by electronic devices attached to the capacitors, such as transistors or diodes, which conduct a small amount of current even when they are turned off. Even though this off current is an order of magnitude less than the current through the device when it is on, the current still slowly discharges the capacitor. Another contributor to leakage from a capacitor is from the undesired imperfection of some dielectric materials used in capacitors, also known as ''dielectric leakage''. It is a result of the dielectric material not being a perfect insulator and having some non-zero conducti ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Capacitance
Capacitance is the ability of an object to store electric charge. It is measured by the change in charge in response to a difference in electric potential, expressed as the ratio of those quantities. Commonly recognized are two closely related notions of capacitance: ''self capacitance'' and ''mutual capacitance''. An object that can be electrically charged exhibits self capacitance, for which the electric potential is measured between the object and ground. Mutual capacitance is measured between two components, and is particularly important in the operation of the capacitor, an elementary linear electronic component designed to add capacitance to an electric circuit. The capacitance between two conductors depends only on the geometry; the opposing surface area of the conductors and the distance between them; and the permittivity of any dielectric material between them. For many dielectric materials, the permittivity, and thus the capacitance, is independent of the potential ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
PCI Local Bus
Peripheral Component Interconnect (PCI) is a local bus, local computer Computer bus, bus for attaching Computer hardware, hardware devices in a computer and is part of the PCI Local Bus standard. The PCI bus supports the functions found on a System bus, processor bus but in a standardized format that is independent of any given Processor (computing), processor's native bus. Devices connected to the PCI bus appear to a bus mastering, bus master to be connected directly to its own bus and are assigned addresses in the processor's address space. It is a parallel communication, parallel bus, synchronous circuit, synchronous to a single clock signal, bus clock. Attached devices can take either the form of an integrated circuit fitted onto the motherboard (called a ''planar device'' in the PCI specification) or an expansion card that fits into a slot. The PCI Local Bus was first implemented in IBM PC compatibles, where it displaced the combination of several slow Industry Standard Arc ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Pull-up Resistor
In electronic logic circuits, a pull-up resistor (PU) or pull-down resistor (PD) is a resistor used to ensure a known state for a signal. More specifically, a pull-up resistor or pull-down resistor ensures that a wire will have a high logic level or low logic level, respectively, in the absence of a driving signal. It is typically used in combination with components such as switches and transistors, which physically interrupt the connection of subsequent components to Ground (electricity), ground or to IC power-supply pin, VCC. A closed switch creates a direct connection to ground or VCC, but without a PU or PD, when the switch is open, the rest of the circuit would be left floating (i.e. it would have an indeterminate voltage), which is generally undesirable. For a switch that is used to connect a circuit to ground, a pull-up resistor (connected between the circuit and VCC) ensures a well-defined voltage (i.e. VCC) when the switch is open. For a switch that is used to connect ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Light-emitting Diodes
A light-emitting diode (LED) is a semiconductor device that emits light when current flows through it. Electrons in the semiconductor recombine with electron holes, releasing energy in the form of photons. The color of the light (corresponding to the energy of the photons) is determined by the energy required for electrons to cross the band gap of the semiconductor. White light is obtained by using multiple semiconductors or a layer of light-emitting phosphor on the semiconductor device. Appearing as practical electronic components in 1962, the earliest LEDs emitted low-intensity infrared (IR) light. Infrared LEDs are used in Remote control, remote-control circuits, such as those used with a wide variety of consumer electronics. The first visible-light LEDs were of low intensity and limited to red. Early LEDs were often used as indicator lamps, replacing small Incandescent light bulb, incandescent bulbs, and in seven-segment displays. Later developments produced LEDs ava ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Charlieplexing
Charlieplexing (also known as tristate multiplexing, reduced pin-count LED multiplexing, complementary LED drive and crossplexing) is a technique for accessing a large number of LEDs, switches, micro-capacitors or other I/O entities, using relatively few tri-state logic wires from a microcontroller. These I/O entities can be wired as discrete components, x/y arrays, or woven in a diagonally intersecting pattern to form diagonal arrays. Etymology Although the technique was introduced in 2001 by Maxim Integrated, the name "Charlieplexing", however, first occurred in a 2003 application note. It was named after Charles "Charlie" M. Allen, an applications engineer of MAX232 fame, who had proposed this method internally. How and why to use Charlieplexing The simplest way to address a single pixel (or input button) is to run a wire out to it and another wire back to ground, but this requires a lot of wiring. A slight improvement is to have everything return on a common groun ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Multiplexer
In electronics, a multiplexer (or mux; spelled sometimes as multiplexor), also known as a data selector, is a device that selects between several Analog signal, analog or Digital signal (electronics), digital input signals and forwards the selected input to a single output line. The selection is directed by a separate set of digital inputs known as select lines. A multiplexer of 2^n inputs has n select lines, which are used to select which input line to send to the output. A multiplexer makes it possible for several input signals to share one device or resource, for example, one analog-to-digital converter or one communications transmission medium, instead of having one device per input signal. Multiplexers can also be used to implement Boolean algebra, Boolean functions of multiple variables. Conversely, a demultiplexer (or demux) is a device that takes a single input signal and selectively forwards it to one of several output lines. A multiplexer is often used with a complem ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Backplane
A backplane or backplane system is a group of electrical connectors in parallel with each other, so that each pin of each connector is linked to the same relative pin of all the other connectors, forming a computer bus. It is used to connect several printed circuit boards together to make up a complete computer system. Backplanes commonly use a printed circuit board, but wire-wrapped backplanes have also been used in minicomputers and high-reliability applications. A backplane is generally differentiated from a motherboard by the lack of on-board processing and storage elements. A backplane uses plug-in cards for storage and processing. Usage Early microcomputer systems like the Altair 8800 used a backplane for the processor and expansion cards. Backplanes are normally used in preference to cables because of their greater reliability. In a cabled system, the cables need to be flexed every time that a card is added or removed from the system; this flexing eventually cause ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Printed Circuit Board
A printed circuit board (PCB), also called printed wiring board (PWB), is a Lamination, laminated sandwich structure of electrical conduction, conductive and Insulator (electricity), insulating layers, each with a pattern of traces, planes and other features (similar to wires on a flat surface) Chemical milling, etched from one or more sheet layers of copper laminated onto or between sheet layers of a non-conductive substrate. PCBs are used to connect or Electrical wiring, "wire" Electronic component, components to one another in an electronic circuit. Electrical components may be fixed to conductive pads on the outer layers, generally by soldering, which both electrically connects and mechanically fastens the components to the board. Another manufacturing process adds Via (electronics), vias, metal-lined drilled holes that enable electrical interconnections between conductive layers, to boards with more than a single side. Printed circuit boards are used in nearly all e ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Chip Select
Chip select (CS) or slave select (SS) is the name of a control line in digital electronics used to select one (or a set) of integrated circuit An integrated circuit (IC), also known as a microchip or simply chip, is a set of electronic circuits, consisting of various electronic components (such as transistors, resistors, and capacitors) and their interconnections. These components a ...s (commonly called "chips") out of several connected to the same computer bus, usually utilizing the three-state logic. One bus that uses the chip/slave select is the Serial Peripheral Interface Bus (SPI bus). When an engineer needs to connect several devices to the same set of input wires (e.g., a computer bus), but retain the ability to send and receive data or commands to each device independently of the others on the bus, they can use a chip select. The chip select is a command pin on many integrated circuits which connects the I/O pins on the device to the internal circuitry of tha ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
