Transverse Mercator

The transverse Mercator map projection (TM, TMP) is an adaptation of the standard Mercator projection. The transverse version is widely used in national and international mapping systems around the world, including the Universal Transverse Mercator. When paired with a suitable geodetic datum, the transverse Mercator delivers high accuracy in zones less than a few degrees in east-west extent.

Standard and transverse aspects

The transverse Mercator projection is the transverse aspect of the standard (or ''Normal'') Mercator projection. They share the same underlying mathematical construction and consequently the transverse Mercator inherits many traits from the normal Mercator:
* Both projections are cylindrical: for the Normal Mercator, the axis of the cylinder coincides with the polar axis and the line of tangency with the equator. For the transverse Mercator, the axis of the cylinder lies in the equatorial plane, and the line of tangency is any chosen meridian, thereby designated the '' central meridian''.
* Both projections may be modified to secant forms, which means the scale has been reduced so that the cylinder slices through the model globe.
* Both exist in spherical and ellipsoidal versions.
* Both projections are conformal, so that the point scale is independent of direction and ''local'' shapes are well preserved;
* Both projections have constant scale on the line of tangency (the equator for the normal Mercator and the central meridian for the transverse).

Since the central meridian of the transverse Mercator can be chosen at will, it may be used to construct highly accurate maps (of narrow width) anywhere on the globe. The secant, ellipsoidal form of the transverse Mercator is the most widely applied of all projections for accurate large-scale maps.

Spherical transverse Mercator

In constructing a map on any projection, a sphere is normally chosen to model the Earth when the extent of the mapped region exceeds a few hundred kilometers in length in both dimensions. For maps of smaller regions, an ellipsoidal model must be chosen if greater accuracy is required; see next section. The spherical form of the transverse Mercator projection was one of the seven new projections presented, in 1772, by Johann Heinrich Lambert.Lambert, Johann Heinrich. 1772. ''Anmerkungen und Zusätze zur Entwerfung der Land- und Himmelscharten''. I
Beyträge zum Gebrauche der Mathematik und deren Anwendung, part 3
section 6)Albert Wangerin
(Editor), 1894. ''Ostwalds Klassiker der exakten Wissenschaften''
(54). Published by Wilhelm Engelmann. This is Lambert's paper with additional comments by the editor. Available at th
University of Michigan Historical Math Library
(The text is also available in a modern English translation.Tobler, Waldo R, ''Notes and Comments on the Composition of Terrestrial and Celestial Maps'', 1972 (University of Michigan Press). Reprinted (2010) by Esri

/ref>) Lambert did not name his projections; the name ''transverse Mercator'' dates from the second half of the nineteenth century. This is an excellent survey of virtually all known projections from antiquity to 1993. The principal properties of the transverse projection are here presented in comparison with the properties of the normal projection.

Normal and transverse spherical projections

Ellipsoidal transverse Mercator

The ellipsoidal form of the transverse Mercator projection was developed by Carl Friedrich Gauss in 1822Gauss, Karl Friedrich, 1825. "Allgemeine Auflösung der Aufgabe: die Theile einer gegebnen Fläche auf einer andern gegebnen Fläche so abzubilden, daß die Abbildung dem Abgebildeten in den kleinsten Theilen ähnlich wird" Preisarbeit der Kopenhagener Akademie 1822
Schumacher Astronomische Abhandlungen, Altona, no. 3
p. 5–30. [Reprinted, 1894, Ostwald's Klassiker der Exakten Wissenschaften, no. 55: Leipzig, Wilhelm Engelmann, p. 57–81, with editing by Albert Wangerin, pp. 97–101. Also in Herausgegeben von der Gesellschaft der Wissenschaften zu Göttingen in Kommission bei Julius Springer in Berlin, 1929, v. 12, pp. 1–9.] and further analysed by Johann Heinrich Louis Krüger in 1912.Krüger, L. (1912).
Konforme Abbildung des Erdellipsoids in der Ebene
'. Royal Prussian Geodetic Institute, New Series 52.

The projection is known by several names: the ''(ellipsoidal) transverse Mercator'' in the US; Gauss conformal or Gauss–Krüger in Europe; or Gauss–Krüger transverse Mercator more generally.
Other than just a synonym for the ellipsoidal transverse Mercator map projection, the term Gauss–Krüger may be used in other slightly different ways:
* Sometimes, the term is used for a particular computational method for transverse Mercator: that is, how to convert between latitude/longitude and projected coordinates. There is no simple closed formula to do so when the earth is modelled as an ellipsoid. But the ''Gauss–Krüger'' method gives the same results as other methods, at least if you are sufficiently near the central meridian: less than 100 degrees of longitude, say. Further away, some methods become inaccurate.
* The term is also used for a particular set of transverse Mercator projections used in narrow zones in Europe and South America, at least in Germany, Turkey, Austria, Slovenia, Croatia, Bosnia-Herzegovina, Serbia, Montenegro, North Macedonia, Finland and Argentina. This ''Gauss–Krüger'' system is similar to the universal transverse Mercator system, but the central meridians of the Gauss–Krüger zones are only 3° apart, as opposed to 6° in UTM.

The projection is conformal with a constant scale on the central meridian. (There are other conformal generalisations of the transverse Mercator from the sphere to the ellipsoid but only Gauss-Krüger has a constant scale on the central meridian.) Throughout the twentieth century the Gauss–Krüger transverse Mercator was adopted, in one form or another, by many nations (and international bodies); in addition it provides the basis for the Universal Transverse Mercator series of projections. The Gauss–Krüger projection is now the most widely used projection in accurate large-scale mapping.

The projection, as developed by Gauss and Krüger, was expressed in terms of low order power series which were assumed to diverge in the east-west direction, exactly as in the spherical version. This was proved to be untrue by British cartographer E. H. Thompson, whose unpublished exact (closed form) version of the projection, reported by Laurence Patrick Lee in 1976,
pp
1–1492–101
an
107–114
showed that the ellipsoidal projection is finite (below). This is the most striking difference between the spherical and ellipsoidal versions of the transverse Mercator projection: Gauss–Krüger gives a reasonable projection of the ''whole'' ellipsoid to the plane, although its principal application is to accurate large-scale mapping "close" to the central meridian.

Features

*Near the central meridian (Greenwich in the above example) the projection has low distortion and the shapes of Africa, western Europe, the British Isles, Greenland, and Antarctica compare favourably with a globe.
* The central regions of the transverse projections on sphere and ellipsoid are indistinguishable on the small-scale projections shown here.
*The meridians at 90° east and west of the chosen central meridian project to horizontal lines through the poles. The more distant hemisphere is projected above the north pole and below the south pole.
*The equator bisects Africa, crosses South America and then continues onto the complete outer boundary of the projection; the top and bottom edges and the right and left edges must be identified (i.e. they represent the same lines on the globe). (Indonesia is bisected.)
*Distortion increases towards the right and left boundaries of the projection but it does not increase to infinity. Note the Galapagos Islands where the 90° west meridian meets the equator at bottom left.
*The map is conformal. Lines intersecting at any specified angle on the ellipsoid project into lines intersecting at the same angle on the projection. In particular parallels and meridians intersect at 90°.
*The point scale factor is independent of direction at any point so that the shape of a ''small'' region is reasonably well preserved. The necessary condition is that the magnitude of scale factor must not vary too much over the region concerned. Note that while South America is distorted greatly the island of Ceylon is small enough to be reasonably shaped although it is far from the central meridian.
*The choice of central meridian greatly affects the appearance of the projection. If 90°W is chosen then the whole of the Americas is reasonable. If 145°E is chosen the Far East is good and Australia is oriented with north up.

In most applications the Gauss–Krüger coordinate system is applied to a narrow strip near the central meridians where the differences between the spherical and ellipsoidal versions are small, but nevertheless important in accurate mapping. Direct series for scale, convergence and distortion are functions of eccentricity and both latitude and longitude on the ellipsoid: inverse series are functions of eccentricity and both ''x'' and ''y'' on the projection. In the secant version the lines of true scale on the projection are no longer parallel to central meridian; they curve slightly. The convergence angle between projected meridians and the ''x'' constant grid lines is no longer zero (except on the equator) so that a grid bearing must be corrected to obtain an azimuth from true north. The difference is small, but not negligible, particularly at high latitudes.

Implementations of the Gauss–Krüger projection

In his 1912 paper, Krüger presented two distinct solutions, distinguished here by the expansion parameter:
* Krüger–''n'' (paragraphs 5 to 8): Formulae for the direct projection, giving the coordinates ''x'' and ''y'', are fourth order expansions in terms of the third flattening, ''n'' (the ratio of the difference and sum of the major and minor axes of the ellipsoid). The coefficients are expressed in terms of latitude (''φ''), longitude (''λ''), major axis (''a'') and eccentricity (''e''). The inverse formulae for ''φ'' and ''λ'' are also fourth order expansions in ''n'' but with coefficients expressed in terms of ''x'', ''y'', ''a'' and ''e''.
* Krüger–''λ'' (paragraphs 13 and 14): Formulae giving the projection coordinates ''x'' and ''y'' are expansions (of orders 5 and 4 respectively) in terms of the longitude ''λ'', expressed in radians: the coefficients are expressed in terms of ''φ'', ''a'' and ''e''. The inverse projection for ''φ'' and ''λ'' are sixth order expansions in terms of the ratio , with coefficients expressed in terms of ''y'', ''a'' and ''e''. (See Transverse Mercator: Redfearn series.)

The Krüger–''λ'' series were the first to be implemented, possibly because they were much easier to evaluate on the hand calculators of the mid twentieth century.
*Lee–Redfearn–OSGB: In 1945, L. P. LeeLee L. P., (1945). Survey Review, Volume 8 (Part 58), pp 142–152
''The transverse Mercator projection of the spheroid''
(Errata and comments in Volume 8 (Part 61), pp. 277–278. confirmed the ''λ'' expansions of Krüger and proposed their adoption by the OSGBA guide to coordinate systems in Great Britain. This is available as a pdf document at
but Redfearn (1948)Redfearn, J C B (1948). Survey Review, Volume 9 (Part 69), pp 318–322
''Transverse Mercator formulae''
pointed out that they were not accurate because of (a) the relatively high latitudes of Great Britain and (b) the great width of the area mapped, over 10 degrees of longitude. Redfearn extended the series to eighth order and examined which terms were necessary to attain an accuracy of 1 mm (ground measurement). The Redfearn series are still the basis of the OSGB map projections.
*Thomas–UTM: The ''λ'' expansions of Krüger were also confirmed by Paul Thomas in 1952: they are readily available in Snyder. His projection formulae, completely equivalent to those presented by Redfearn, were adopted by the United States Defence Mapping Agency as the basis for the UTM. They are also incorporated into the Geotrans coordinate converter made available by the United States National Geospatial-Intelligence Agenc


*Other countries: The Redfearn series are the basis for geodetic mapping in many countries: Australia, Germany, Canada, South Africa to name but a few. (A list is given in Appendix A.1 of Stuifbergen 2009.)
*Many variants of the Redfearn series have been proposed but only those adopted by national cartographic agencies are of importance. For an example of modifications which do not have this status see Transverse Mercator: Bowring series). All such modifications have been eclipsed by the power of modern computers and the development of high order ''n''-series outlined below. The precise Redfearn series, although of low order, cannot be disregarded as they are still enshrined in the quasi-legal definitions of OSGB and UTM etc.

The Krüger–''n'' series have been implemented (to fourth order in ''n'') by the following nations.
*France
*Finland
*Sweden
*Japan

Higher order versions of the Krüger–''n'' series have been implemented to seventh order by Ensager and PoderK. E. Engsager and K. Poder, 2007
A highly accurate world wide algorithm for the transverse Mercator mapping (almost)
in Proc. XXIII Intl. Cartographic Conf. (ICC2007), Moscow, p. 2.1.2. and to tenth order by Kawase.Kawase, K. (2011)
A General Formula for Calculating Meridian Arc Length and its Application to Coordinate Conversion in the Gauss–Krüger Projection
Bulletin of the Geospatial Information Authority of Japan, 59, pp 1–13 Apart from a series expansion for the transformation between latitude and conformal latitude, Karney has implemented the series to thirtieth order.

Exact Gauss–Krüger and accuracy of the truncated series

An exact solution by E. H. Thompson is described by L. P. Lee. It is constructed in terms of elliptic functions (defined in chapters 19 and 22 of the NIST handbook) which can be calculated to arbitrary accuracy using algebraic computing systems such as Maxima.Maxima, 2009, A computer algebra system, version 5.20.1, URL http://maxima.sf.net. Such an implementation of the exact solution is described by Karney (2011).C. F. F. Karney (2011),
Transverse Mercator with an accuracy of a few nanometers
', J. Geodesy 85(8), 475-485 (2011); preprint of paper and C++ implementation of algorithms are available a

The exact solution is a valuable tool in assessing the accuracy of the truncated ''n'' and λ series. For example, the original 1912 Krüger–''n'' series compares very favourably with the exact values: they differ by less than 0.31 μm within 1000 km of the central meridian and by less than 1 mm out to 6000 km. On the other hand, the difference of the Redfearn series used by Geotrans and the exact solution is less than 1 mm out to a longitude difference of 3 degrees, corresponding to a distance of 334 km from the central meridian at the equator but a mere 35 km at the northern limit of an UTM zone. Thus the Krüger–''n'' series are very much better than the Redfearn λ series.

The Redfearn series becomes much worse as the zone widens. Karney discusses Greenland as an instructive example. The long thin landmass is centred on 42W and, at its broadest point, is no more than 750 km from that meridian while the span in longitude reaches almost 50 degrees. Krüger–''n'' is accurate to within 1 mm but the Redfearn version of the Krüger–''λ'' series has a maximum error of 1 kilometre.

Karney's own 8th-order (in ''n'') series is accurate to 5 nm within 3900 km of the central meridian.

Formulae for the spherical transverse Mercator

Spherical normal Mercator revisited

The normal cylindrical projections are described in relation to a cylinder tangential at the equator with axis along the polar axis of the sphere. The cylindrical projections are constructed so that all points on a meridian are projected to points with $x = a\lambda$ (where $a$ is the Earth radius) and $y$ is a prescribed function of $\phi$. For a tangent Normal Mercator projection the (unique) formulae which guarantee conformality are:
:x = a\lambda\,,\qquad
y = a\ln \left tan \left(\frac + \frac \right)\right = \frac\ln\left frac\right

Conformality implies that the point scale, ''k'', is independent of direction: it is a function of latitude only:
:$k(\varphi)=\sec\varphi.\,$
For the secant version of the projection there is a factor of ''k'' on the right hand side of all these equations: this ensures that the scale is equal to ''k'' on the equator.

Normal and transverse graticules

The figure on the left shows how a transverse cylinder is related to the conventional graticule on the sphere. It is tangential to some arbitrarily chosen meridian and its axis is perpendicular to that of the sphere. The ''x''- and ''y''-axes defined on the figure are related to the equator and central meridian exactly as they are for the normal projection. In the figure on the right a rotated graticule is related to the transverse cylinder in the same way that the normal cylinder is related to the standard graticule. The 'equator', 'poles' (E and W) and 'meridians' of the rotated graticule are identified with the chosen central meridian, points on the equator 90 degrees east and west of the central meridian, and great circles through those points.

The position of an arbitrary point (''φ'',''λ'') on the standard graticule can also be identified in terms of angles on the rotated graticule: ''φ′'' (angle M′CP) is an effective latitude and −''λ′'' (angle M′CO) becomes an effective longitude. (The minus sign is necessary so that (''φ′'',''λ′'') are related to the rotated graticule in the same way that (''φ'',''λ'') are related to the standard graticule). The Cartesian (''x′'',''y′'') axes are related to the rotated graticule in the same way that the axes (''x'',''y'') axes are related to the standard graticule.

The tangent transverse Mercator projection defines the coordinates (''x′'',''y′'') in terms of −''λ′'' and ''φ′'' by the transformation formulae of the tangent Normal Mercator projection:
:x' = -a\lambda'\,\qquad
y' = \frac
\ln\left frac\right

This transformation projects the central meridian to a straight line of finite length and at the same time projects the great circles through E and W (which include the equator) to infinite straight lines perpendicular to the central meridian. The true parallels and meridians (other than equator and central meridian) have no simple relation to the rotated graticule and they project to complicated curves.

The relation between the graticules

The angles of the two graticules are related by using spherical trigonometry on the spherical triangle NM′P defined by the true meridian through the origin, OM′N, the true meridian through an arbitrary point, MPN, and the great circle WM′PE. The results are:
:$\begin \sin\varphi'&=\sin\lambda\cos\varphi,\\ \tan\lambda'&=\sec\lambda\tan\varphi. \end$

Direct transformation formulae

The direct formulae giving the Cartesian coordinates (''x'',''y'') follow immediately from the above. Setting ''x'' = ''y′'' and ''y'' = −''x′'' (and restoring factors of ''k'' to accommodate secant versions)
:
\begin
x(\lambda,\varphi)&= \frack_0a
\ln\left \frac
\right\\ pxy(\lambda,\varphi)&= k_0 a\arctan\left sec\lambda\tan\varphi\right
\end

The above expressions are given in Lambert and also (without derivations) in Snyder,This paper can be downloaded fro
USGS pages.
It gives full details of most projections, together with interesting introductory sections, but it does not derive any of the projections from first principles. Maling. and OsborneThe Mercator Projections
Detailed derivations of all formulae quoted in this article (with full details).

Inverse transformation formulae

Inverting the above equations gives
:
\begin
\lambda(x,y)&
= \arctan\left \sinh\frac
\sec\frac \right
\\ px \varphi(x,y)&= \arcsin\left \mbox\;\frac
\sin\frac \right
\end

Point scale

In terms of the coordinates with respect to the rotated graticule the point scale factor is given by ''k'' = sec ''φ′'': this may be expressed either in terms of the geographical coordinates or in terms of the projection coordinates:
:
\begin
k(\lambda,\varphi)&=\frac,\\ pxk(x,y)&=k_0\cosh\left(\frac\right).
\end

The second expression shows that the scale factor is simply a function of the distance from the central meridian of the projection. A typical value of the scale factor is ''k'' = 0.9996 so that ''k'' = 1 when ''x'' is approximately 180 km. When ''x'' is approximately 255 km and ''k'' = 1.0004: the scale factor is within 0.04% of unity over a strip of about 510 km wide.

Convergence

The convergence angle ''γ'' at a point on the projection is defined by the angle measured ''from'' the projected meridian, which defines true north, ''to'' a grid line of constant ''x'', defining grid north. Therefore, ''γ'' is positive in the quadrant north of the equator and east of the central meridian and also in the quadrant south of the equator and west of the central meridian. The convergence must be added to a grid bearing to obtain a bearing from true north. For the secant transverse Mercator the convergence may be expressed either in terms of the geographical coordinates or in terms of the projection coordinates:
:
\begin
\gamma(\lambda,\varphi)&=\arctan(\tan\lambda\sin\varphi),\\ px\gamma(x,y)&=\arctan\left(\tanh\frac\tan\frac\right).
\end

Formulae for the ellipsoidal transverse Mercator

Details of actual implementations

* Gauss-Kruger series in longitude: Transverse Mercator: Redfearn series
* Gauss-Kruger series in ''n'' (third flattening): Transverse Mercator: flattening series
* Exact (closed form) transverse Mercator projection: Transverse Mercator: exact solution
* Fourth order Redfearn series by concise formulae (example): Transverse Mercator: Bowring series

Coordinates, grids, eastings and northings

The projection coordinates resulting from the various developments of the ellipsoidal transverse Mercator are Cartesian coordinates such that the central meridian corresponds to the ''x'' axis and the equator corresponds to the ''y'' axis. Both ''x'' and ''y'' are defined for all values of ''λ'' and ''ϕ''. The projection does not define a grid: the grid is an independent construct which could be defined arbitrarily. In practice the national implementations, and UTM, do use grids aligned with the Cartesian axes of the projection, but they are of finite extent, with origins which need not coincide with the intersection of the central meridian with the equator.

The true grid origin is always taken on the central meridian so that grid coordinates will be negative west of the central meridian. To avoid such negative grid coordinates, standard practice defines a false origin to the west (and possibly north or south) of the grid origin: the coordinates relative to the false origin define eastings and northings which will always be positive. The false easting, ''E''₀, is the distance of the true grid origin east of the false origin. The false northing, ''N''₀, is the distance of the true grid origin north of the false origin. If the true origin of the grid is at latitude ''φ''₀ on the central meridian and the scale factor the central meridian is ''k''₀ then these definitions give eastings and northings by:
:
\begin
E&=E_0+x(\lambda,\varphi),\\ px N&=N_0+y(\lambda,\varphi)-k_0 m(\varphi_0).
\end

The terms "eastings" and "northings" do not mean strict east and north directions. Grid lines of the transverse projection, other than the ''x'' and ''y'' axes, do not run north-south or east-west as defined by parallels and meridians. This is evident from the global projections shown above. Near the central meridian the differences are small but measurable. The difference between the north-south grid lines and the true meridians is the angle of convergence.

See also

* List of map projections
* Mercator projection
* Scale (map)
* Oblique Mercator projection

References