Rocket propellant-1
   HOME

TheInfoList



OR:

RP-1 (alternatively, Rocket Propellant-1 or Refined Petroleum-1) is a highly refined form of kerosene outwardly similar to
jet fuel Jet fuel or aviation turbine fuel (ATF, also abbreviated avtur) is a type of aviation fuel designed for use in aircraft powered by gas-turbine engines. It is colorless to straw-colored in appearance. The most commonly used fuels for commercial a ...
, used as rocket fuel. RP-1 provides a lower specific impulse than liquid hydrogen (LH2), but is cheaper, is stable at room temperature, and presents a lower explosion hazard. RP-1 is far denser than LH2, giving it a higher
energy density In physics, energy density is the amount of energy stored in a given system or region of space per unit volume. It is sometimes confused with energy per unit mass which is properly called specific energy or . Often only the ''useful'' or extract ...
(though its
specific energy Specific energy or massic energy is energy per unit mass. It is also sometimes called gravimetric energy density, which is not to be confused with energy density, which is defined as energy per unit volume. It is used to quantify, for example, sto ...
is lower). RP-1 also has a fraction of the toxicity and carcinogenic hazards of
hydrazine Hydrazine is an inorganic compound with the chemical formula . It is a simple pnictogen hydride, and is a colourless flammable liquid with an ammonia-like odour. Hydrazine is highly toxic unless handled in solution as, for example, hydrazine ...
, another room-temperature liquid fuel.


Usage and history

RP-1 is a fuel in the first-stage boosters of the Electron, Soyuz,
Zenit Zenit, meaning "zenith", may refer to: Spaceflight and rocketry * Zenit (rocket family), a Soviet family of space launch vehicles * Zenit (satellite), a type of Soviet spy satellite * Zenit sounding rocket, a Swiss rocket Sports * Zenit (sports ...
, Delta I-III, Atlas, Falcon, Antares, and
Tronador II Tronador (Spanish for Thunderer) is a series of Argentine rockets, including the Tronador I and Tronador II vehicles, to develop a liquid-propellant rocket expendable launch system called ISCUL (''Inyector Satelital de Cargas Utiles Ligeras'', ...
rockets. It also powered the first stages of the
Energia Energia or Energiya may refer to: * Energia (corporation), or S. P. Korolev Rocket and Space Corporation Energia, a Russian design bureau and manufacturer ** Energia (rocket), a Soviet rocket designed by the company *Energia (company), a company th ...
, Titan I, Saturn I and IB, and Saturn V. The Indian Space Research Organization (ISRO) is also developing an RP-1 fueled engine for its future rockets.


Development

During and immediately after World War II, alcohols (primarily ethanol, occasionally
methanol Methanol (also called methyl alcohol and wood spirit, amongst other names) is an organic chemical and the simplest aliphatic alcohol, with the formula C H3 O H (a methyl group linked to a hydroxyl group, often abbreviated as MeOH). It is a ...
) were commonly used as fuels for large liquid-fueled rockets. Their high
heat of vaporization The enthalpy of vaporization (symbol ), also known as the (latent) heat of vaporization or heat of evaporation, is the amount of energy (enthalpy) that must be added to a liquid substance to transform a quantity of that substance into a gas. T ...
kept regeneratively-cooled engines from melting, especially considering that alcohols would typically contain several percent water. However, it was recognized that hydrocarbon fuels would increase engine efficiency, due to a slightly higher density, the lack of an oxygen atom in the fuel molecule, and negligible water content. Regardless of which hydrocarbon was chosen, it would also have to replace alcohol as a coolant. Many early rockets burned kerosene, but as burn times, combustion efficiencies, and combustion-chamber pressures increased, engine masses decreased, which led to unmanageable engine temperatures. Raw kerosene used as coolant tends to dissociate and polymerize. Lightweight products in the form of gas bubbles cause cavitation, and heavy ones in the form of wax deposits block narrow cooling passages in the engine. The resulting coolant starvation raises temperatures further, and causes more polymerization which accelerates breakdown. The cycle rapidly escalates (i.e. thermal runaway) until an engine wall rupture or other mechanical failure occurs, and it persists even when the entire coolant flow consists of kerosene. In the mid-1950s rocket designers turned to the chemists to formulate a heat-resistant hydrocarbon, with the result being RP-1. During the 1950s, LOX ( liquid oxygen) became the preferred oxidizer to use with RP-1, though other oxidizers have also been employed.


Fractions and formulation

First, sulfur and sulfur compounds attack metals at high temperatures, and even very small amounts of sulfur assist polymerization. Therefore, sulfur and sulfur compounds are kept to a minimum. Alkenes,
alkyne \ce \ce Acetylene \ce \ce \ce Propyne \ce \ce \ce \ce 1-Butyne In organic chemistry, an alkyne is an unsaturated hydrocarbon containing at least one carbon—carbon triple bond. The simplest acyclic alkynes with only one triple bond and n ...
s, and aromatics are also held to low levels, as they tend to polymerize at high temperatures and long periods of storage. At the time, it was thought that kerosene-fueled missiles might remain in storage for years awaiting activation. This function was later transferred to
solid-fuel rocket A solid-propellant rocket or solid rocket is a rocket with a rocket engine that uses solid propellants ( fuel/oxidizer). The earliest rockets were solid-fuel rockets powered by gunpowder; they were used in warfare by the Arabs, Chinese, Persian ...
s, though the high-temperature benefits of saturated hydrocarbons remained. Because of the low levels of alkenes and aromatics, RP-1 is less toxic than various jet and diesel fuels, and far less toxic than gasoline. The more desirable
isomer In chemistry, isomers are molecules or polyatomic ions with identical molecular formulae – that is, same number of atoms of each element – but distinct arrangements of atoms in space. Isomerism is existence or possibility of isomers. Iso ...
s were selected or synthesized, with
linear alkane In organic chemistry, an alkane, or paraffin (a historical trivial name that also has other meanings), is an acyclic saturated hydrocarbon. In other words, an alkane consists of hydrogen and carbon atoms arranged in a tree structure in ...
s being reduced in number in favor of greater numbers of cyclic and highly branched alkanes. Just as cyclic and branched molecules improve
octane rating An octane rating, or octane number, is a standard measure of a fuel's ability to withstand compression in an internal combustion engine without detonating. The higher the octane number, the more compression the fuel can withstand before detonating ...
in petrol, they also significantly increase thermal stability at high temperatures. The most desirable isomers are polycyclics such as ladderanes. In contrast, the main applications of kerosene (aviation, heating, and lighting), are much less concerned with thermal breakdown and therefore do not require stringent optimisation of their isomers, although sulfur and sulfur compounds are still minimized. In production, these grades are processed tightly to remove impurities and side fractions. Ashes were feared likely to block fuel lines and engine passages, and wear away valves and turbopump bearings, as these are lubricated by the fuel. Slightly too-heavy or too-light fractions affected lubrication abilities and were likely to separate during storage and under load. The remaining hydrocarbons are at or near C12 mass. Because of the lack of light hydrocarbons, RP-1 has a high
flash point The flash point of a material is the "lowest liquid temperature at which, under certain standardized conditions, a liquid gives off vapours in a quantity such as to be capable of forming an ignitable vapour/air mixture". (EN 60079-10-1) The fl ...
and is less of a fire hazard than petrol. All told, the final product is much more expensive than common kerosene. Although any petroleum can produce RP-1 with enough processing, real-world rocket-grade kerosene is sourced from a small number of oil fields with high-quality base stock, or it can be artificially synthesized. This, coupled with the relatively small demand in a niche market compared to other petroleum users, drives RP-1's high price. Military specifications of RP-1 are covered in MIL-R-25576, and the chemical and physical properties of RP-1 are described in NISTIR 6646. In Russia and other former Soviet countries, the two main rocket kerosene formulations are T-1 and RG-1. Densities are slightly higher, 0.82 to 0.85 g/ml, compared to RP-1 at 0.81 g/ml. For a short period, the Soviets achieved even higher densities by super-chilling the kerosene in the rocket's fuel tanks, but this partially defeated the purpose of using kerosene over other super-chilled fuels. In the case of the Soyuz and R-7, the temperature penalty was minor. Facilities were already in place to manage the vehicle's cryogenic liquid oxygen and
liquid nitrogen Liquid nitrogen—LN2—is nitrogen in a liquid state at low temperature. Liquid nitrogen has a boiling point of about . It is produced industrially by fractional distillation of liquid air. It is a colorless, low viscosity liquid that is wide ...
, both of which are far colder than the kerosene. The launcher's central kerosene tank is surrounded on four sides and the top by liquid-oxygen tanks; the liquid-nitrogen tank is nearby at the bottom. The kerosene tanks of the four boosters are relatively small and compact, and also between a liquid-oxygen and a liquid-nitrogen tank. Thus, once the kerosene was chilled initially, it could remain so for the brief time needed to finish launch preparations. The latest version of Falcon 9, Falcon 9 Full Thrust, also has the capability of sub-cooling the RP-1 fuel to −7 °C, giving a 2.5–4% density increase.


Comparison with other fuels

Chemically, a hydrocarbon propellant is less efficient than hydrogen fuel because hydrogen releases more energy per unit mass during combustion, enabling a higher exhaust velocity. This is, in part, a result of the high mass of carbon atoms relative to hydrogen atoms. Hydrocarbon engines are also typically run fuel-rich, which produces some CO instead of CO2 as a consequence of incomplete combustion, although this is not unique to hydrocarbon engines, as hydrogen engines are also typically run fuel-rich for the best overall performance. Some Russian engines run their turbopump preburners oxygen-rich, but the main combustion chamber is still run fuel-rich. All told, kerosene engines generate a in the range of 270 to 360 seconds, while hydrogen engines achieve 370 to 465 seconds. During engine shutdown, fuel flow goes to zero rapidly, while the engine is still quite hot. Residual and trapped fuel can polymerize or even
carbonize Carbonization is the conversion of organic matters like plants and dead animal remains into carbon through destructive distillation. Complexity in carbonization Carbonization is a pyrolytic reaction, therefore, is considered a complex process ...
at hot spots or in hot components. Even without hot spots, heavy fuels can create a petroleum residue, as can be seen in gasoline, diesel, or jet fuel tanks that have been in service for years. Rocket engines have cycle lifetimes measured in minutes or even seconds, preventing truly heavy deposits. However, rockets are much more sensitive to a deposit, as described above. Thus, kerosene systems generally entail more teardowns and overhauls, creating operations and labor expenses. This is a problem for expendable engines, as well as reusable ones, because engines must be ground-fired some number of times before launch. Even cold-flow tests, in which the propellants are not ignited, can leave residues. On the upside, below a chamber pressure of about , kerosene can produce sooty deposits on the inside of the nozzle and chamber liner. This acts as a significant insulation layer and can reduce the heat flow into the wall by roughly a factor of two. Most modern hydrocarbon engines, however, run above this pressure, therefore this is not a significant effect for most engines. Recent heavy-hydrocarbon engines have modified components and new operating cycles, in attempts to better manage leftover fuel, achieve a more-gradual cooldown, or both. This still leaves the problem of non-dissociated petroleum residue. Other new engines have tried to bypass the problem entirely, by switching to light hydrocarbons such as methane or
propane Propane () is a three-carbon alkane with the molecular formula . It is a gas at standard temperature and pressure, but compressible to a transportable liquid. A by-product of natural gas processing and petroleum refining, it is commonly used a ...
gas. Both are volatiles, so engine residues simply evaporate. If necessary, solvents or other purgatives can be run through the engine to finish dispersion. The short-chain carbon backbone of propane (a C3 molecule) is very difficult to break; methane, with a single carbon atom (C1), is technically not a chain at all. The breakdown products of both molecules are also gases, with fewer problems due to phase separation, and much less likelihood of polymerization and deposition. However, methane (and to a lesser extent propane) reintroduces handling inconveniences that prompted kerosenes in the first place. The low vapor pressure of kerosenes gives safety for ground crews. However, in flight the kerosene tank needs a separate pressurization system to replace fuel volume as it drains. Generally, this is a separate tank of liquid or high-pressure inert gas, such as nitrogen or helium. This creates extra cost and weight.
Cryogenic In physics, cryogenics is the production and behaviour of materials at very low temperatures. The 13th IIR International Congress of Refrigeration (held in Washington DC in 1971) endorsed a universal definition of “cryogenics” and “cr ...
or volatile propellants generally do not need a separate pressurant; instead, some propellant is expanded (often with engine heat) into low-density gas and routed back to its tank. A few highly volatile propellant designs do not even need the gas loop; some of the liquid automatically vaporizes to fill its own container. Some rockets use gas from a gas generator to pressurize the fuel tank; usually, this is exhaust from a turbopump. Although this saves the weight of a separate gas system, the loop now has to handle a hot, reactive gas instead of a cool, inert one. Regardless of chemical constraints, RP-1 has supply constraints due to the very small size of the launch-vehicle industry versus other consumers of petroleum. While the material price of such a highly refined hydrocarbon is still less than many other rocket propellants, the number of RP-1 suppliers is limited. A few engines have attempted to use more standard, widely distributed petroleum products such as jet fuel or even diesel, fo Regardless of chemical constraints, RP-1 has supply constraints due to the very small size of the launch-vehicle industry versus other consumers of petroleum. While the material price of such a highly refined hydrocarbon is still less than many other rocket propellants, the number of RP-1 suppliers is limited. A few engines have attempted to use more standard, widely distributed petroleum products such as jet fuel or even diesel (for example, ABL Space Systems' E2 engine can run on either RP-1 or Jet-A). By using alternate or supplemental engine cooling methods, some engines can tolerate the non-optimal formulations. Any hydrocarbon-based fuel produces more air pollution when burned than hydrogen alone. Hydrocarbon combustion produces carbon dioxide (CO2), carbon monoxide (CO), and hydrocarbon (HC) emissions, while hydrogen (H2) reacts with oxygen (O2) to produce only water (H2O), with some unreacted H2 also released. Both hydrocarbon-based fuels and hydrogen fuel will create oxides of nitrogen (NO''x'') pollutants, because rocket exhaust temperatures above 1600°C (2900°F) will thermally combine some of the nitrogen (N2) and oxygen (O2) already present in the atmosphere, to create oxides of nitrogen.


RP-1-like fuels

Robert H. Goddard's initial rockets used gasoline. While the RP-1 specification was being developed, Rocketdyne was experimenting with
diethyl cyclohexane In organic chemistry, an ethyl group (abbr. Et) is an alkyl substituent with the formula , derived from ethane (). ''Ethyl'' is used in the International Union of Pure and Applied Chemistry's nomenclature of organic chemistry for a saturated ...
. While superior to RP-1, it was never adopted for use – its formulation was not finished before development of Atlas and Titan I (designed around RP-1) leading to RP-1 becoming the standard hydrocarbon rocket fuel. Soviet formulations are discussed above. In addition, the Soviets briefly used syntin (russian: link=no, синтин), a higher-energy formulation, used in upper stages. Syntin is 1-methyl-1,2-dicyclopropyl cyclopropane (). Russia is also working to switch the Soyuz-2 from RP-1 to "naftil" or "naphthyl". After the RP-1 standard, RP-2 was developed. The primary difference is an even lower sulfur content. However, as most users accept RP-1, there was little incentive to produce and stock a second, even rarer and more expensive formulation. The OTRAG group launched test vehicles using more common blends. In at least one instance, a rocket was propelled by diesel fuel. However, no OTRAG rocket came even close to orbit.


References

{{Reflist, 30em


External links


NASA page on propellants




Rocket fuels