A lever tumbler lock is a type of

lock Lock(s) may refer to: Common meanings *Lock and key, a mechanical device used to secure items of importance *Lock (water navigation), a device for boats to transit between different levels of water, as in a canal Arts and entertainment * ''Lock ...

that uses a set of levers to prevent the bolt from moving in the lock. In the simplest form of these, lifting the tumbler above a certain height will allow the bolt to slide past. The number of levers may vary, but is usually an odd number for a lock that can be opened from each side of the door in order to provide symmetry. A minimum number of levers may be specified to provide an anticipated level of security (see five-lever locks section).

History

"Double acting" lever tumbler locks were invented in 1778 by Robert Barron of England. These required the lever to be lifted to a certain height by having a slot cut in the lever, so lifting the lever too far was as bad as not lifting the lever far enough. This type of lock is still used today, on doors in

Europe Europe is a large peninsula conventionally considered a continent in its own right because of its great physical size and the weight of its history and traditions. Europe is also considered a Continent#Subcontinents, subcontinent of Eurasia ...

Africa Africa is the world's second-largest and second-most populous continent, after Asia in both cases. At about 30.3 million km2 (11.7 million square miles) including adjacent islands, it covers 6% of Earth's total surface area ...

South America South America is a continent entirely in the Western Hemisphere and mostly in the Southern Hemisphere, with a relatively small portion in the Northern Hemisphere at the northern tip of the continent. It can also be described as the sou ...

and some other parts of the world. Lever Lock and Key

Design

The lock is made up of levers (usually made out of non-ferrous metals). Each lever needs to be lifted to a specific height by the key in order for the locking bolt to move. Typically, the belly of the lever is cut away to various depths to provide different combinations, or the gate is cut in a different location, to provide differs. A lever will have ''pockets'' (or ''gates'') through which the bolt ''stump'' (or ''post'' or ''fence'') moves during unlocking. There has not always been universal agreement about which variants of the basic design merit the terms "lever lock" or "detainer lock" or both. Some authors use the term "detainer lock" to refer specifically to variants where the gates are "open" (i.e. at the edge of the lever), rather than "closed" (i.e. entirely surrounded by the lever). Lever locks generally use a bitted key. Some locks used on safes use a double-bitted key, as do some door locks of a type often used in Southern and Eastern Europe.

Three-lever locks

A three-lever lock is a common type of lever lock, but is generally used for low security applications such as internal doors as their tolerances are much lower (there are fewer combinations of key available, so they are likely to unlock doors they shouldn't).

Five-lever locks

A five-lever lock is often required for

home insurance Home insurance, also commonly called homeowner's insurance (often abbreviated in the US real estate industry as HOI), is a type of property insurance that covers a private residence. It is an insurance policy that combines various personal insu ...

and often recommended by the police for home security. There are various grades but the current British Standard (BS3621:2007) is usually required for insurance purposes. Locksmith Valerie Olifent states that, "The doors of many historic churches still carry an old wooden lock although often you find that a modern 5-lever mortice lock has been installed alongside it to meet insurance requirements.""The Ancient Art of the Locksmith" http://www.buildingconservation.com/articles/locks/locks.htm BS3621:2007 requires a bolt throw of 20 mm rather than the 14 mm of the earlier British Standard. Most BS3621 locks have anti-pick devices built in to reduce the chance of lock picking, along with hardened bolts and anti-drill plates to reduce risk of physical attack.

Vulnerabilities

Lever tumbler locks can be picked with a tool called a ''curtain pick'' which is inserted into the keyway of the lock, and a force is applied to the locking bolt. The pick is then used to lift each lever inside the lock to the correct height so that the locking bolt can pass. Higher security lever locks (such as the five-lever) usually have notches cut into the levers. These catch the locking bolt and prevent it from moving if picking is attempted (similar to the security pins in a

pin tumbler lock The pin tumbler lock is a lock mechanism that uses pins of varying lengths to prevent the lock from opening without the correct key. Pin tumblers are most commonly employed in cylinder locks, but may also be found in tubular pin tumbler locks ( ...

). The

Chubb detector lock A Chubb detector lock is a lever tumbler lock with an integral security feature, a Combination lock#Internal mechanisms, re-locking device, which frustrates unauthorised access attempts and indicates to the lock's owner that it has been interfered ...

is a variation of the lever lock which was designed to detect and prevent picking attempts. Lever locks can be drilled, but usually a template or stencil is required to mark the drilling point, as the lock mechanism is commonly mortised into the door and so it is harder to determine the point at which to drill.

References