IEEE 802.1Q, often referred to as Dot1q, is the

networking Network, networking and networked may refer to: Science and technology * Network theory, the study of graphs as a representation of relations between discrete objects * Network science, an academic field that studies complex networks Mathematic ...

standard that supports virtual local area networking (VLANs) on an

IEEE 802.3 IEEE 802.3 is a working group and a collection standards defining the physical layer and data link layer's media access control (MAC) of wired Ethernet. The standards are produced by the working group of Institute of Electrical and Electronics ...

Ethernet Ethernet () is a family of wired computer networking technologies commonly used in local area networks (LAN), metropolitan area networks (MAN) and wide area networks (WAN). It was commercially introduced in 1980 and first standardized in 1 ...

network. The standard defines a system of VLAN tagging for

Ethernet frame In computer networking, an Ethernet frame is a data link layer protocol data unit and uses the underlying Ethernet physical layer transport mechanisms. In other words, a data unit on an Ethernet link transports an Ethernet frame as its payload ...

s and the accompanying procedures to be used by

bridges A bridge is a structure built to span a physical obstacle (such as a body of water, valley, road, or rail) without blocking the way underneath. It is constructed for the purpose of providing passage over the obstacle, which is usually someth ...

and

switches In electrical engineering, a switch is an electrical component that can disconnect or connect the conducting path in an electrical circuit, interrupting the electric current or diverting it from one conductor to another. The most common type of ...

in handling such frames. The standard also contains provisions for a quality-of-service prioritization scheme commonly known as

IEEE 802.1p IEEE P802.1p was a task group active from 1995 to 1998, responsible for adding traffic class expediting and dynamic multicast filtering to the IEEE 802.1D standard. The task group developed a mechanism for implementing quality of service (QoS) at ...

and defines the Generic Attribute Registration Protocol. Portions of the network which are VLAN-aware (i.e., IEEE 802.1Q conformant) can include VLAN tags. When a frame enters the VLAN-aware portion of the network, a tag is added to represent the VLAN membership. Each frame must be distinguishable as being within exactly one VLAN. A frame in the VLAN-aware portion of the network that does not contain a VLAN tag is assumed to be flowing on the native VLAN. The standard was developed by

IEEE 802.1 IEEE 802.1 is a working group of the IEEE 802 project of the IEEE Standards Association. It is concerned with: * 802 LAN/MAN architecture * internetworking among 802 LANs, MANs and wide area networks * 802 Link Security * 802 overall network manage ...

, a

working group A working group, or working party, is a group of experts working together to achieve specified goals. The groups are domain-specific and focus on discussion or activity around a specific subject area. The term can sometimes refer to an interdis ...

of the

IEEE 802 IEEE 802 is a family of Institute of Electrical and Electronics Engineers (IEEE) standards for local area networks (LAN), personal area network (PAN), and metropolitan area networks (MAN). The IEEE 802 LAN/MAN Standards Committee (LMSC) maintai ...

standards committee, and continues to be actively revised. One of the notable revisions is 802.1Q-2014 which incorporated IEEE 802.1aq (Shortest Path Bridging) and much of the

IEEE 802.1D IEEE 802.1D is the Ethernet MAC bridges standard which includes bridging, Spanning Tree Protocol and others. It is standardized by the IEEE 802.1 working group. It includes details specific to linking many of the other 802 projects including t ...

standard.

Frame format

802.1Q adds a 32-bit field between the source

MAC address A media access control address (MAC address) is a unique identifier assigned to a network interface controller (NIC) for use as a network address in communications within a network segment. This use is common in most IEEE 802 networking te ...

and the

EtherType EtherType is a two-Octet (computing), octet field in an Ethernet frame. It is used to indicate which Communications protocol, protocol is Encapsulation (networking), encapsulated in the payload of the frame and is used at the receiving end by th ...

fields of the original frame. Under 802.1Q, the maximum frame size is extended from 1,518 bytes to 1,522 bytes. The minimum frame size remains 64 bytes, but a bridge may extend the minimum size frame from 64 to 68 bytes on transmission. This allows a tag to be popped without needing additional padding. Two bytes are used for the tag protocol identifier (TPID), the other two bytes for tag control information (TCI). The TCI field is further divided into PCP, DEI, and VID. ;Tag protocol identifier (TPID) :A 16-bit field set to a value of 0x8100 in order to identify the frame as an IEEE 802.1Q-tagged frame. This field is located at the same position as the EtherType field in untagged frames, and is thus used to distinguish the frame from untagged frames. ;Tag control information (TCI) :A 16-bit field containing the following sub-fields: :;Priority code point (PCP) ::A 3-bit field which refers to the

class of service (CoS) and maps to the frame priority level. Different PCP values can be used to prioritize different classes of traffic. :;Drop eligible indicator (DEI) ::A 1-bit field. (formerly CFI) May be used separately or in conjunction with PCP to indicate frames eligible to be dropped in the presence of congestion. :;VLAN identifier (VID) ::A 12-bit field specifying the VLAN to which the frame belongs. The values of 0 and 4095 (0x000 and 0xFFF in

hexadecimal In mathematics and computing, the hexadecimal (also base-16 or simply hex) numeral system is a positional numeral system that represents numbers using a radix (base) of 16. Unlike the decimal system representing numbers using 10 symbols, he ...

) are reserved. All other values may be used as VLAN identifiers, allowing up to 4,094 VLANs. The reserved value 0x000 indicates that the frame does not carry a VLAN ID; in this case, the 802.1Q tag specifies only a priority (in PCP and DEI fields) and is referred to as a ''priority tag''. On bridges, VID 0x001 (the default VLAN ID) is often reserved for a

network management Network management is the process of administering and managing computer networks. Services provided by this discipline include fault analysis, performance management, provisioning of networks and maintaining quality of service. Network managem ...

VLAN; this is vendor-specific. The VID value 0xFFF is reserved for implementation use; it must not be configured or transmitted. 0xFFF can be used to indicate a wildcard match in management operations or filtering database entries. For frames (other than 802.3 frames) using

Subnetwork Access Protocol The Subnetwork Access Protocol (SNAP) is a mechanism for multiplexing, on networks using IEEE 802.2 LLC, more protocols than can be distinguished by the 8-bit 802.2 Service Access Point (SAP) fields. SNAP supports identifying protocols by EtherT ...

(SNAP) encapsulation with an organizationally unique identifier (OUI) field of 00-00-00 (so that the protocol ID field in the SNAP header is an EtherType as specified in ), the EtherType value in the SNAP header is set to 0x8100 and the aforementioned extra 4 bytes are appended after the SNAP header. In other words the VLAN tag follows the SNAP header. For 802.3 frames in LLC-SNAP format, the order is opposite; the VLAN tag is placed ''before'' the LLC-SNAP header. Because inserting the VLAN tag changes the frame, 802.1Q encapsulation forces a recalculation of the original

frame check sequence A frame check sequence (FCS) is an error-detecting code added to a frame in a communication protocol. Frames are used to send payload data from a source to a destination. Purpose All frames and the bits, bytes, and fields contained within ...

field in the Ethernet trailer. The IEEE 802.3ac standard increased the maximum Ethernet frame size from 1518 bytes to 1522 bytes to accommodate the four-byte VLAN tag. Some network devices that do not support the larger frame size will process these frames successfully but may report them as "baby giant" anomalies.

Double tagging

IEEE 802.1ad IEEE 802.1ad is an Ethernet networking standard. It is as an amendment to IEEE standard IEEE 802.1Q-1998 and was incorporated into the base 802.1Q standard in 2011. The technique specified by the standard is known as provider bridging and stack ...

introduced the concept of double tagging. Double tagging can be useful for

internet service provider An Internet service provider (ISP) is an organization that provides services for accessing, using, or participating in the Internet. ISPs can be organized in various forms, such as commercial, community-owned, non-profit, or otherwise priva ...

s (ISPs), allowing them to use their VLANs internally while carrying traffic from clients that is already VLAN tagged. The outer (next to source MAC and representing ISP VLAN) S-TAG (service tag) comes first, followed by the inner C-TAG (customer tag). In such cases, 802.1ad specifies a TPID of 0x88a8 for service-provider outer S-TAG.

Other protocols

IEEE 802.1Q defines the

Multiple VLAN Registration Protocol Multiple Registration Protocol (MRP), which replaced Generic Attribute Registration Protocol (GARP), is a generic registration framework defined by the IEEE 802.1ak amendment to the IEEE 802.1Q standard. MRP allows bridges, switches or other sim ...

(MVRP), an application of the

Multiple Registration Protocol Multiple Registration Protocol (MRP), which replaced Generic Attribute Registration Protocol (GARP), is a generic registration framework defined by the IEEE 802.1ak amendment to the IEEE 802.1Q standard. MRP allows bridges, switches or other sim ...

, allowing bridges to negotiate the set of VLANs to be used over a specific link. MVRP replaced the slower

GARP VLAN Registration Protocol Multiple Registration Protocol (MRP), which replaced Generic Attribute Registration Protocol (GARP), is a generic registration framework defined by the IEEE 802.1ak amendment to the IEEE 802.1Q standard. MRP allows bridges, switches or other sim ...

(GVRP) in 2007 with the IEEE 802.1ak-2007 amendment. The 2003 revision of the standard was the first to include the

Multiple Spanning Tree Protocol The Multiple Spanning Tree Protocol (MSTP) and algorithm, provides both simple and full connectivity assigned to any given Virtual LAN (VLAN) throughout a Bridged Local Area Network. MSTP uses BPDUs to exchange information between spanning-tree ...

(MSTP) which was originally defined in IEEE 802.1s.

Frame format

Double tagging

Other protocols

See also