Extended memory

In DOS memory management, extended memory refers to memory above the first megabyte (2²⁰ bytes) of address space in an IBM PC or compatible with an 80286 or later processor. The term is mainly used under the DOS and Windows operating systems. DOS programs, running in real mode or virtual x86 mode, cannot directly access this memory, but are able to do so through an application programming interface called the ''Extended Memory Specification'' (XMS). This API is implemented by a driver (such as HIMEM.SYS) or the operating system, which takes care of memory management and copying memory between conventional and extended memory, by temporarily switching the processor into protected mode. In this context, the term "extended memory" may refer to either the whole of the extended memory or only the portion available through this API.

Extended memory can also be accessed directly by DOS programs running in protected mode using VCPI or DPMI, two (different and incompatible) methods of using protected mode under DOS.

Extended memory should not be confused with expanded memory (EMS), an earlier method for expanding the IBM PC's memory capacity beyond 640 kB (655,360 bytes) using an expansion card with bank switched memory modules. Because of the available support for expanded memory in popular applications, device drivers were developed that emulated expanded memory using extended memory. Later two additional methods were developed allowing direct access to a small portion of extended memory from real mode. These memory areas are referred to as the high memory area (HMA) and the upper memory area (UMA; also referred to as upper memory blocks or UMBs).

Overview

On x86-based PCs, extended memory is only available with an Intel 80286 processor or higher. Only these chips can address more than 1 megabyte of RAM. The earlier 8086/ 8088 processors can make use of more than 1 MB of RAM if one employs special hardware to make selectable parts of it appear at addresses below 1 MB.

On a 286 or better PC equipped with more than 640 kB of RAM, the additional memory would generally be re-mapped above the 1 MB boundary, since the IBM PC architecture reserves addresses between 640 kB and 1 MB for system ROM and peripherals.

Extended memory is not accessible in real mode (except for a small portion called the high memory area). Only applications executing in protected mode can use extended memory directly. A supervising protected-mode operating system such as Microsoft Windows manages application programs' access to memory. The processor makes this memory available through the Global Descriptor Table (GDT) and one or more Local Descriptor Tables (LDTs). The memory is "protected" in the sense that memory segments assigned a local descriptor cannot be accessed by another program because that program uses a different LDT, and memory segments assigned a global descriptor can have their access rights restricted, causing a processor exception (e.g., a general protection fault or GPF) on violation. This prevents programs running in protected mode from interfering with each other's memory.

A protected-mode operating system such as Microsoft Windows can also run real-mode programs and provide expanded memory to them. The DOS Protected Mode Interface (DPMI) is Microsoft's prescribed method for an DOS program to access extended memory under a multitasking environment.

''Extended Memory Specification'' (XMS)

The ''Extended Memory Specification'' (XMS) is the specification describing the use of IBM PC extended memory in real mode for storing data (but not for running executable code in it). Memory is made available by extended memory manager (XMM) software such as HIMEM.SYS. The XMM functions are accessible through software interrupt 2Fh function 4310h.

XMS version 2.0, released in July 1988, allowed for up to 64 MB of memory, with XMS version 3.0 this increased to 4 GB (2³² bytes). To differentiate between the possibly different amount of memory that might be available to applications, depending on which version of the specification they were developed to, the latter may be referred to as super extended memory (SXMS).

The extended memory manager is also responsible for managing allocations in the high memory area (HMA) and the upper memory area (UMA; also referred to as upper memory blocks or UMBs). In practice the upper memory area will be provided by the expanded memory manager (EMM), after which DOS will try to allocate them all and manage them itself.

See also

* DOS memory management
* Conventional memory
* Expanded memory (EMS)
* High memory area (HMA)
* Upper memory area (UMA)
* Global EMM Import Specification (GEMMIS)
* Unreal mode

References

; Specifications
* Microsoft, Lotus, Intel, and AST Research (1988-07-19)
''eXtended Memory Specification (XMS), version 2.0''

* Microsoft, Lotus, Intel, and AST Research (January 1991)
''eXtended Memory Specification (XMS), version 3.0''

; Microsoft Knowledge Base
*
*
*

External links

Extended Memory (XMS) Specification

{{DEFAULTSORT:Extended Memory
X86 memory management
DOS memory management
Memory expansion