Dual-tone multi-frequency signaling (DTMF) is an in-band telecommunication signaling system using the voice-frequency band over telephone lines between telephone equipment and other communications devices and switching centers. DTMF was first developed in the Bell System in the United States, and became known under the trademark Touch-Tone for use in push-button telephones supplied to telephone customers, starting in 1963. DTMF is standardized as ITU-T Recommendation Q.23. It is also known in the UK as MF4.
The Touch-Tone system using a telephone keypad gradually replaced the use of rotary dial and has become the industry standard for landline and mobile service. Other multi-frequency systems are used for internal signaling within the telephone network.
Prior to the development of DTMF, telephone numbers were dialed by users with a loop-disconnect (LD) signaling, more commonly known as pulse dialing (dial pulse, DP) in the U.S. It functions by interrupting the current in the local loop between the telephone exchange and the calling party's telephone at a precise rate with a switch in the telephone that is operated by the rotary dial as it spins back to its rest position after having been rotated to each desired number. The exchange equipment responds to the dial pulses either directly by operating relays, or by storing the number in a digit register recording the dialed number. The physical distance for which this type of dialing was possible was restricted by electrical distortions and was only possible on direct metallic links between end points of a line. Placing calls over longer distances required either operator assistance or provision of special subscriber trunk dialing equipment. Operators used an earlier type of multi-frequency signaling.
Multi-frequency signaling (MF) is a group of signaling methods that use a mixture of two pure tone (pure sine wave) sounds. Various MF signaling protocols were devised by the Bell System and CCITT. The earliest of these were for in-band signaling between switching centers, where long-distance telephone operators used a 16-digit keypad to input the next portion of the destination telephone number in order to contact the next downstream long-distance telephone operator. This semi-automated signaling and switching proved successful in both speed and cost effectiveness. Based on this prior success with using MF by specialists to establish long-distance telephone calls, dual-tone multi-frequency signaling was developed for end-user signaling without the assistance of operators.
The DTMF system uses a set of eight audio frequencies transmitted in pairs to represent 16 signals, represented by the ten digits, the letters A to D, and the symbols # and *. As the signals are audible tones in the voice frequency range, they can be transmitted through electrical repeaters and amplifiers, and over radio and microwave links, thus eliminating the need for intermediate operators on long-distance circuits.
AT&T described the product as "a method for pushbutton signaling from customer stations using the voice transmission path." In order to prevent consumer telephones from interfering with the MF-based routing and switching between telephone switching centers, DTMF frequencies differ from all of the pre-existing MF signaling protocols between switching centers: MF/R1, R2, CCS4, CCS5, and others that were later replaced by SS7 digital signaling. DTMF was known throughout the Bell System by the trademark Touch-Tone. The term was first used by AT&T in commerce on July 5, 1960 and was introduced to the public on November 18, 1963, when the first push-button telephone was made available to the public. It was a registered trademark by AT&T from September 4, 1962 to March 13, 1984. It is standardized by ITU-T Recommendation Q.23. In the UK, it is also known as MF4.
Other vendors of compatible telephone equipment called the Touch-Tone feature tone dialing or DTMF, or used their other trade names such as Digitone by Northern Electric Company in Canada.
As a method of in-band signaling, DTMF signals were also used by cable television broadcasters to indicate the start and stop times of local commercial insertion points during station breaks for the benefit of cable companies. Until out-of-band signaling equipment was developed in the 1990s, fast, unacknowledged DTMF tone sequences could be heard during the commercial breaks of cable channels in the United States and elsewhere. Previously, terrestrial television stations used DTMF tones to control remote transmitters.
How DTMF dialing sounds.
Problems playing this file? See media help.
The engineers had envisioned telephones being used to access computers and automated response systems. They consulted with companies to determine the requirements. This led to the addition of the number sign (#, ''pound'' or "diamond" in this context, "hash", "square" or "gate" in the UK, and "octothorpe'' by the original engineers) and asterisk or "star" (*) keys as well as a group of keys for menu selection: A, B, C and D. In the end, the lettered keys were dropped from most phones, and it was many years before the two symbol keys became widely used for vertical service codes such as *67 in the United States of America and Canada to suppress caller ID.
The AUTOVON telephone system of the United States Armed Forces used these signals to assert certain privilege and priority levels when placing telephone calls. Precedence is still a feature of military telephone networks, but using number combinations. For example, entering 93 before a number is a priority call.
Present-day uses of the A, B, C and D signals on telephone networks are few, and are exclusive to network control. For example, the A key is used on some networks to cycle through different carriers at will. The A, B, C and D tones are used in radio phone patch and repeater operations to allow, among other uses, control of the repeater while connected to an active phone line.
The *, #, A, B, C and D keys are still widely used worldwide by amateur radio operators and commercial two-way radio systems for equipment control, repeater control, remote-base operations and some telephone communications systems.
DTMF signaling tones can also be heard at the start or end of some VHS (Video Home System) cassette tapes. Information on the master version of the video tape is encoded in the DTMF tone. The encoded tone provides information to automatic duplication machines, such as format, duration and volume levels, in order to replicate the original video as closely as possible.
The DTMF telephone keypad is laid out in a 4×4 matrix of push buttons in which each row represents the low frequency component and each column represents the high frequency component of the DTMF signal. Pressing a key sends a combination of the row and column frequencies. For example, the key 1 produces a superimposition of tones of 697 and 1209 hertz (Hz). Initial pushbutton designs employed levers, so that each button activated two contacts. The tones are decoded by the switching center to determine the keys pressed by the user.
|1209 Hz||1336 Hz||1477 Hz||1633 Hz|
DTMF was originally decoded by tuned filter banks. By the end of the 20th century, digital signal processing became the predominant technology for decoding. DTMF decoding algorithms typically use the Goertzel algorithm. As DTMF signaling is often transmitted in-band with voice or other audio signals present simultaneously, the DTMF signal definition includes strict limits for timing (minimum duration and interdigit spacing), frequency deviations, harmonics, and amplitude relation of the two components with respect to each other (twist).
National telephone systems define other tones that indicate the status of lines, equipment, or the result of calls. Such call-progress tones are often also composed of multiple frequencies and are standardized in each country. The Bell System defines them in the Precise Tone Plan. However, such signaling systems are not considered to belong to the DTMF system.