Delaware-class battleship

The ''Delaware''-class battleships of the United States Navy were the second class of American dreadnoughts. With this class, the limit imposed on capital ships by the United States Congress was waived, which allowed designers at the Navy's Bureau of Construction and Repair to correct what they considered flaws in the preceding and produce ships not only more powerful but also more effective and rounded overall. Launched in 1909, these ships became the first in US naval history to exceed .

The ''Delaware''s carried a battery of ten guns in five turrets, an increase of two guns over the ''South Carolina''s. With these ships, the US Navy re-adopted a full-fledged medium-caliber weapon for anti-torpedo boat defense. While the gun was smaller than that used by other major navies, this would, with few exceptions, become the standard medium-gun caliber for the US Navy for the better part of the 20th century. As for speed, the ''Delaware''s were capable of , a significant improvement over the earlier class's . This would become the speed for all American standard-type battleships. Propulsion systems were mixed; while was fitted with steam turbines, retained triple-expansion engines. Direct-drive turbines were much less fuel-efficient, a significant concern for a Navy with Pacific responsibilities but lacking Britain's extensive network of coaling stations.

These ships saw varied service during their careers. During World War I, ''Delaware'' was part of Battleship Division Nine of the US Atlantic Fleet, and was assigned to the British Grand Fleet. She escorted convoys and participated in the blockade of the German High Seas Fleet. In contrast, ''North Dakota'' remained on the American coast throughout the war, due in part to worries about her troublesome turbine engines. Post-war, they conducted training cruises with the US Atlantic Fleet. In 1924, ''Delaware'' was broken up for scrap metal in accordance with the Washington Naval Treaty of 1922. ''North Dakota'' survived until 1931, when she too was scrapped, under the terms of the 1930 London Naval Treaty.

Design

Prompted by the launch of and misinformation about , the US Navy and Congress faced what they perceived as a vastly better battleship than the two battleships then under construction, which were designed under tonnage constraints that Congress had imposed on capital ships. Actually, the ''South Carolina''s were inferior only in speed to ''Dreadnought''; they carried fewer heavy guns but, unlike ''Dreadnought'', could bring all of them to bear on the broadside. Because of this, they could fire an equal weight of metal. Also, because greater time and care had been taken with their armor and bulkhead arrangement, they were better protected than the British ship. None of this was realized at the time. Nevertheless, the Navy's Bureau of Construction and Repair (C&R) had struggled tremendously to design an adequate warship under congressional limits and had taken battleship design as far under those restrictions as it could. Seeing now that those limits had become unrealistic, Congress ended them; any subsequent constraints would be dictated by treaty limitations. The language of the authorizing act of June 26, 1906 was for a battleship "carrying as heavy armor and as a powerful armament as any known vessel of its class, to have the highest practicable speed and the greatest practicable radius of action."

The ''Delaware'' class was the second of 11 distinct US capital ship designs begun from 1906 to 1919; some 29 battleships and six battlecruisers were laid down during this period, though seven of the battleships and all six of the battlecruisers were cancelled. Except for the s, these were all relatively slow ships, designed for no more than . They ranged in displacement from . At this time, no US dreadnought class battleship had yet hit the water as all were either at some stage of building or in design. Virtually the entire US Navy battle line was being designed by drawing on experience from pre-dreadnought designs, or from observation of foreign battleship design.

The design for these ships was actually ready in 1905 or 1906. Two variants were offered—a 10-gun version on and a 12-gun alternative on . The larger ship was rejected as too expensive for the firepower it offered, even after its displacement was reduced to tons. Also, because C&R was required to consider private designs, construction on the ''Delaware''s did not commence until 1907. None of the private designs was considered remotely satisfactory by the Navy. However, Fore River later developed its version into the battleship , which was built for the Argentine navy. While the C&R design was considered superior, it still came under criticism, particularly for the poor placement of, and lack of protection for, the secondary armament.

General characteristics

The ''Delaware''s were significantly more powerful than their predecessors, the ''South Carolina''-class, and are mentioned by ''Conway's All the World's Fighting Ships'' as the first to match the standard set by the British with ''Dreadnought''. This was due in large part to the elimination of Congressional limits on the size of new battleships; the only restriction the Congress placed on their design was that the cost of hull and machinery could not exceed 6 million USD. The ''Delaware''-class ships were also significantly larger than the ''South Carolina''s. They were long at the waterline and long overall. By comparison, the ''South Carolina''-class ships were long overall. The ''Delaware''s had a beam of and a draft of ; the ''South Carolina''s measurements were and , respectively. The ''Delaware''-class ships displaced at standard displacement and at full load, while the ''South Carolina''s displaced at standard displacement and at full load. Their bows had an early example of bulbous forefeet.PIANC MarCom Working Group 08: ''The Damage Inflicted by Ships with Bulbous Bows on Underwater Structures'' (Supplement to Bulletin nr. 70, PTC2 report of WG 08 - 1990 issue), page 6

Propulsion

For reasons including expected hostilities with Japan, requiring travel across the Pacific Ocean, long operational range was a recurrent theme in all US battleship designs. As an experiment, these ships received different powerplants. ''Delaware'' received triple-expansion reciprocating engines, while ''North Dakota'' was fitted with Curtiss direct drive steam turbine engines. Both ships had 14 Babcock & Wilcox boilers, both original power plants were rated at ; and both ships were capable of reaching 21 knots. Chief Constructor Washington L. Capps predicted ''North Dakota'' would have a 25 percent shorter radius than ''Delaware'' at 16 knots and 45 percent less at 14 knots, based on tank tests and the known performance of steam turbines at that time. This estimate was proved true during the ships' trial runs in 1909. Also, because ''Delaware''s engine bearings were equipped with forced lubrication instead of a gravity-fed system, she was able to steam at full speed for 24 hours without any need for engine repair. This would normally have been unthinkable as reciprocating engines were known generally to shake themselves apart if run at full power for long. However, this penchant for reliability came under question in the late 1930s as battleships with reciprocating engines performed poorly in the Pacific. By 1917, more powerful and efficient geared turbines had been installed in ''North Dakota'' to replace her Curtiss turbines. These provided horsepower, some greater than her original engines.

Armament

Main guns

The ''Delaware''-class ships were armed with ten 12-inch/45 caliber Mark 5 guns in five twin gun turrets; this was an addition of two guns compared to the preceding ''South Carolina''s. The gun housings were the Mark 7 type, and they allowed for depression to −5 degrees and elevation to 15 degrees. The guns had a rate of fire of 2 to 3 rounds per minute. They fired shells, of either armor-piercing (AP) or Common types, though the Common type was obsolete by 1915 and put out of production. The propellant charge was in silk bags, and provided a muzzle velocity of . The guns were expected to fire 175 rounds before the barrels would require replacement. The two ships carried 100 shells per gun, or 1,000 rounds in total. At 15 degrees elevation, the guns could hit targets out to approximately .

Two turrets were mounted fore in a superfiring pair, while the other three were mounted aft of the main superstructure, all on the centerline. The placement of the rear gun turrets proved problematic. Capps placed the rear superfiring turret, Number 3, closest amidships. Since it represented the greatest weight borne by the ship's structure due to its tall barbette, this placement would allow it support by the greatest amount of underwater volume available. The other two rear turrets, Numbers 4 and 5, were placed level and back to back. This arrangement was detrimental in two ways. First, Number 3 could not fire astern with Number 4 trained forward, which left only the two 12" guns of Number 5 to do so. Second, because the engine room was situated between Numbers 3 and 4, steam lines ran from the boiler rooms amidships around the ammunition magazine for Number 3 turret to the engine room. These lines, it was later found, had the potential to heat the powder in the magazine and degrade its ballistics. This design flaw was also prevalent in several British dreadnoughts but was considered inescapable by naval designers on structural grounds.

Another challenge with the main armament was that its weight, per turret, which had to be spread over much of the hull, led to increased stress on the structure. The closer the weight of the heavy guns to the ends, the greater the stress and risk for structural failure due to metal fatigue. High speed required fine ends, which were not especially buoyant, and the amount of space needed amidships for machinery precluded moving the main turrets further inboard. Not having to worry about a displacement limit allowed Capps the option of deepening the hull, which helped to some extent. He added a forecastle to allow for better seakeeping and to make room for officers' quarters and restored the full height of the hull aft. The problem itself, however remained.

Secondary guns

The Naval War College in its 1905 Newport Summer Conference considered the guns fitted to the ''South Carolina'' class too light for effective anti-torpedo-boat defense. A committee on this issue formed during the conference suggested that a gun with a high velocity and flat trajectory would work best—one powerful enough to smash an attacking vessel yet light enough for easy handling and rapid firing. For this purpose, the committee found 5-inch guns appeared best suited. During the ''Delaware''s' design, C&R considered guns but concerns voiced by the Naval War College about the lack of heavy splinter protection for these guns and smoke uptakes led to an adaption of 5-inch /50 caliber guns to balance the increase in armor weight.

The ''Delaware''s mounted fourteen 5-inch/50 caliber Mark 6 guns, two forward on the main deck, 10 in casemates on the side and two aft on the main deck abeam No. 5 turret. They had a rate of fire of 6 to 8 rounds per minute. They fired three types of rounds: a "light" AP shell that weighed and a "heavy" AP round that weighed . The third type was the Common Mark 15 shell, which also weighed 50 lb. The 50 lb shells were fired at a muzzle velocity of , while the larger 60 lb shells traveled at a slightly slower . The guns were emplaced on both Mark 9 and Mark 12 pedestal mounts; the Mark 9 version limited elevation to 15 degrees, while the Mark 12 allowed for up to 25 degrees. The 5-inch/50 was able to penetrate most effectively at , which was the deciding factor in the decision to equip the ''Delaware'' class with them. The 5-inch guns were supplied with a total of 240 rounds per barrel.

While these guns were considered an improvement by the Navy over that of the ''South Carolina''s, their placement remained problematic as even in calm water, they were extremely wet and thus difficult to man. The forward guns were moved into the superstructure after sea trials. The casemate-mounted secondary armament was one deck below the main deck and provided the majority of the complaints from shipping water from the forward positions and breaking the flow of the bow wave imparting extra drag on the design.

Anti-aircraft guns

As with the ''South Carolina'' class, these ships were fitted with two 3-inch/50 caliber anti-aircraft (AA) guns in Mark 11 mounts in 1917. The Mark 11 mount was the first 3-inch AA mounting issued by the US Navy. They had a trunnion height of compared to a height of for the pedestal mountings used against surface craft. This allowed them an elevation range between −10 and 85 degrees. Maximum range was at 43 degrees and maximum ceiling at 85 degrees.

Torpedo tubes

The ''Delaware''s carried two torpedo tubes below the waterline. The Bliss-Leavitt 21-inch Mark 3 Model 1 torpedo designed for these tubes had an overall length of , a weight of and propelled an explosive charge of of TNT to a range of at a speed of

Armor

The armored belt ranged in thickness from in the more important areas of the ship. Casemated guns mounted in the hull had between of armor plate. The barbettes that housed the main gun turrets were armored with between of armor; the side portions more vulnerable to shell fire were thicker, while the front and rear sections of the barbette, which were less likely to be hit, received thinner armor to save weight. The gun turrets themselves were armored with of armor. The conning tower was thick. As in the designs of all early dreadnoughts, the deck armor was very thin at in most areas and over machinery and magazine spaces. These ships were expected to do most of their firing at ranges less than . At such distances, deck strikes would be a rare event.

Service history

USS ''Delaware''

During trials, ''Delaware'' was run at full speed for 24 hours straight to prove that her machinery could handle the stress. She was the first American battleship to achieve the feat. Late in 1910, ''Delaware'' sailed to Europe, followed by a trip to South America early in 1911. She made a further two voyages to Europe in 1912 and 1913, before returning to the US Atlantic Fleet for training exercises that were conducted in the western Atlantic and Caribbean. ''Delaware'' took part in the Second battle of Vera Cruz in April–May 1914.

When the United States declared war on Germany in April 1917, ''Delaware'' was initially tasked with readiness training off the East Coast. Late in the year, she was deployed to Europe as part of the US Navy's Battleship Division Nine, under the command of Rear Admiral Hugh Rodman. The force arrived on 7 December and was assigned to the 6th Battle Squadron of the Grand Fleet. In July 1918, ''Delaware'' was withdrawn from overseas service and returned to the United States.

In 1920, the US Navy adopted hull numbers for its ships; ''Delaware'' was assigned the hull number BB-28. ''Delaware'' made only two more cruises, both for midshipmen, under her new identification number: one in 1922 and the second in early 1923. ''Delaware'' sailed to Europe on the second trip, and stopped at a number of ports, including Gibraltar. She returned to the US in August of that year, at which point her crew was reassigned to the newer battleship . She was then taken to the Boston Navy Yard, where her armaments were removed. The ship was decommissioned in November 1923 and sold to shipbreakers in February 1924.

USS ''North Dakota''

Upon commissioning, the ship was assigned to the Atlantic Fleet, alongside her sister ''Delaware''. Her first overseas cruise came in November 1910, when she steamed across the Atlantic to visit France and Britain. ''North Dakota'' also took part in the invasion of Vera Cruz in 1914. Unlike her sister, ''North Dakota'' remained off the American coast for the duration of the United States' involvement in World War I. Hugh Rodman, the commander of the American expeditionary force, specifically requested that ''North Dakota'' be kept stateside; he felt her turbine engines were too unreliable for the ship to be deployed to a war zone. In 1917, her engines were replaced with new geared turbines, and new fire control equipment was installed.

From 1917, she was employed as a training ship for gunners and engineers. Post-war, ''North Dakota'' made a second trip to Europe, primarily to ports in the Mediterranean Sea. During the visit, the ship was tasked with the return of the remains of the Italian ambassador, Vincenzo Macchi di Cellere, who had died 20 October 1919 in Washington, DC. The ship participated in the aerial bombing demonstrations off the Virginia Capes in 1921. In 1923, a third trip to Europe, this time with midshipmen from the Naval Academy aboard. The ship stopped in Spain, Scotland, and Scandinavia.

Like her sister, she was relegated to the surplus naval forces that had to be dismantled under the Washington Naval Treaty. In November 1923, ''North Dakota'' was decommissioned; she had her armaments removed in 1924, after which she was converted into a target ship. She was redesignated as "unclassified", and served as a target until 1931, when she was scrapped.

Footnotes

References

*
*
*
*
*
*
*
*

{{DEFAULTSORT:Delaware Class Battleship
Battleship classes

World War I battleships of the United States