Caterpillar D11

The Caterpillar D11T is a large bulldozer, manufactured by Caterpillar Inc. in East Peoria, Illinois, and mainly used in the mining industry. Primarily designed as a bulldozer, it is also used for push-loading scrapers, and ripping rock overburden.

History

D11N

The D11N was introduced in February 1986 to replace the D10. The D11N had some major improvements over the D10: it includes a bigger track and blade, and a longer track by . The U blade was just under long and high. This increased the blade capacity to . The D11N's weight was . It was powered by a , 3508 V-8 diesel engine. The D11N's improvements made it over 10 percent more productive than the D10. In 1987 a hydraulically powered impact ripper was added to the D11N which raised the weight up to . This would become known as the D11N Impact Ripper.

D11R & D11R Carrydozer

The D11R and D11R Carrydozer were introduced in Las Vegas, Nevada, at MINExpo International in 1996. Both were and that would be increased to later in 1997. Other improvements made to the D11R were fingertip controls and electronic clutch and brakes. The finger tip controls (FTC) allowed the D11R to be steered with small fingertip clutches on the left hand side. The D11R now weighed . The Carrydozer version has a special blade with a curvature that allowed 57 cy ( 43.6 m³) to be pushed. This blade design was introduced by Komatsu on their D575 A-2 dozers in 1995 as the Superdozer version. The deeper curvature of the Carrydozer/Superdozer blades literally carry the dirt moved, and the weight of the load increases pressure on the undercarriage and is thereby increasing the traction of the bulldozer. The increased weight on the undercarriage means also higher contact pressure between rollers and track links, which can increase wear significantly. These higher undercarriage costs must be considered when opting for a Carrydozer version. Komatsu developed a lengthened Superdozer undercarriage with two additional rollers per side to reduce wear, a step that Caterpillar avoided for their Carrydozer machines. The Carrydozer had the structure strengthened considerably for the extra weight and much bigger blade that it carried up front, also, the ripper was fitted with an additional counterweight block. Both D11R and D11R CD received a new Caterpillar 3508B EUI electronically controlled unit injector diesel engine with electronic controls at . The Carrydozer's weight is just over at .Orlemann, Eric C., (2006). - ''Caterpillar''. - St.Paul, Minnesota: MBI. - According to Caterpillar, by the year 2000 over 3,000 D11s had been produced at their plant in East Peoria.

D11T & D11T CD

The current D11T was introduced in early 2008 and is also . It comes as a regular bulldozer and a carrydozer like the previous model. As with the D11R, the D11T Carrydozer can push while the regular D11T can push of earth. A new D11T was on display at the Caterpillar display at Minexpo during the 22 to 24 September 2008 expo in Las Vegas, Nevada.

The D11T and D11T CD are both powered by the CAT C32 engine with ACERT technology. The D11R and the D11T differ in the configuration and layout of their operator controls; several levers have been changed into electronic switches, and several controls have been moved for increased visibility. Another difference is that the D11T has its exhaust mufflers closer to the front of the cab, similar to the D10T. They stand taller than the ones on the D11N/D11R.

In November of 2018, a number of enhancements were introduced and announced for the current D11T/D11T CD machines.

Shipping

These machines are so big that they must be partially dismantled for shipment to most sites. Some are shipped in the United States by railroad flatcars with the blade, push arms and ripper frame removed. Others are dismantled into several units for transport by multiple semi-trailer trucks.Orlemann, Eric C., (2002). ''Colossal Caterpillar: The Ultimate Earthmover''. St. Paul, Minnesota: MBI.

Blade options

The dozer blade on front of the tractor usually comes in three varieties:
* A straight blade ("S-Blade"), which is short and has no lateral curve, no side wings, and can be used for fine grading.
* A universal blade ("U-Blade"), which is tall and very curved, and has large side wings to carry more material.
* A semi universal ( "S-U" Blade ) combination blade, which is shorter, has less curvature, and smaller side wings.

There is also a special "Coal U-Blade", capable of carrying 74.9 cubic metres (98.0 cu yd). These are only attached to bulldozers that work solely on coal.

Applications

D11s are primarily used for moving large quantities of material (dirt, rock, aggregate, soil etc.) short distances in relatively confined places. For example, they are often used in quarries. The D11 is most commonly found in use in large scale forestry, mining, and quarry operations.

D11s can be adapted for agricultural and rock ripping by fitting a ripper, a long claw-like device on the back of the tractor. Rippers can come singly (single shank) or in groups of two or more (multi shank rippers). Usually, a single shank is preferred for heavy ripping.

Ripping rock allows the ground surface rock to be broken into small, easy to handle and transport rubble which can then be removed so that grading can take place.

Agricultural ripping allows rocky or very hard earth to be broken up so that otherwise inarable land can be used for agriculture. For example, much of the best land in the California wine country consists of old lava flows. Ripping shatters the igneous rock, allowing the growth of wine grapes. Hard earth can also be ripped and decompacted to allow the planting of orchards which otherwise could not grow on the land.

Competition

The nearest direct competitor to the Caterpillar D11 is the Komatsu D475.
The Caterpillar D11 can be distinguished from the Komatsu D475 by the elevated drive sprocket, or "High Drive" system, which results in a triangular, rather than oval, shaped track.
The updated version of the Komatsu, the D575A, is the world's largest production bulldozer at and .''Earthmovers Magazine'', October 2008, Page 17, - author Keith Haddock ISSN 1743-0372
A bigger machine, the Acco super bulldozer, was built by Italian firm ACCO, with twin Caterpillar diesel engines giving a combined power of , and weighing , in the 1980s, but this was a custom built model.Haddock, Keith, (2000). - ''Colossal Earthmovers''. - Osceola, Wisconsin: MBI. -

Image gallery

These images are of a Caterpillar D11R III.

File:Cat D11 View 2.jpg, Front-quarter view
File:Cat D11 View 1.jpg, Side view
File:Cat D11 View 3.jpg, Rear-quarter view

See also

* Benjamin Holt
* List of Caterpillar Inc. machines
* Civil engineering
* Heavy equipment
* Komatsu Limited
* Tractor

References

*Orlemann, Eric C.(2006). ''Caterpillar.'' St. Paul, Minnesota: MBI. .

External links

Caterpillar D-Series Track-Type Tractors
— Official Caterpillar website



{{DEFAULTSORT:D11
Caterpillar Inc. vehicles
Tractors
Tracked vehicles
Bulldozers over 100 tonne
Bulldozers with powerplants larger than 500kW