|
10GBASE-KR
10 Gigabit Ethernet (10GE, 10GbE, or 10 GigE) is a group of computer networking technologies for transmitting Ethernet frames at a rate of 10 gigabits per second. It was first defined by the IEEE 802.3ae-2002 standard. Unlike previous Ethernet standards, 10 Gigabit Ethernet defines only full-duplex point-to-point links which are generally connected by network switches; shared-medium CSMA/CD operation has not been carried over from the previous generations Ethernet standards so half-duplex operation and repeater hubs do not exist in 10GbE. The 10 Gigabit Ethernet standard encompasses a number of different physical layer (PHY) standards. A networking device, such as a switch or a network interface controller may have different PHY types through pluggable PHY modules, such as those based on SFP+. Like previous versions of Ethernet, 10GbE can use either copper or fiber cabling. Maximum distance over copper cable is 100 meters but because of its bandwidth requirements, high ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Twinaxial Cabling
Twinaxial cabling, or "Twinax", is a type of cable similar to coaxial cable, but with two inner conductors instead of one. Due to cost efficiency it is becoming common in modern (2013) very-short-range high-speed differential signaling applications. Legacy applications IBM Historically, Twinax was the cable specified for the IBM 5250 terminals and printers, used with IBM's System/34, System/36, System/38, and IBM AS/400 midrange hosts, and with IBM Power Systems machines running IBM i. The data transmission is half-duplex, balanced transmission, at 1 Mbit/s, on a single shielded, 110 Ω twisted pair. With Twinax seven devices can be addressed, from workstation address 0 to 6. The devices do not have to be sequential. Twinax is a bus topology that requires termination to function properly. Most Twinax T-connectors have an automatic termination feature. For use in buildings wired with Category 3 or higher twisted pair there are baluns that convert Twinax to twisted pair and hu ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Line Code
In telecommunication, a line code is a pattern of voltage, current, or photons used to represent digital data transmitted down a communication channel or written to a storage medium. This repertoire of signals is usually called a constrained code in data storage systems. Some signals are more prone to error than others as the physics of the communication channel or storage medium constrains the repertoire of signals that can be used reliably. Common line encodings are unipolar, polar, bipolar, and Manchester code. Transmission and storage After line coding, the signal is put through a physical communication channel, either a transmission medium or data storage medium.Karl Paulsen"Coding for Magnetic Storage Mediums".2007. The most common physical channels are: * the line-coded signal can directly be put on a transmission line, in the form of variations of the voltage or current (often using differential signaling). * the line-coded signal (the ''baseband signal'') un ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Data Signaling Rate
In telecommunication, data signaling rate (DSR), also known as gross bit rate, is the aggregate rate at which data passes a point in the transmission path of a data transmission system. # The DSR is usually expressed in bits per second. # The data signaling rate is given by \sum_^ \frac where ''m'' is the number of parallel channels, ''ni'' is the number of significant conditions of the modulation in the ''i''-th channel, and ''Ti'' is the unit interval, expressed in seconds, for the ''i''-th channel. # For serial transmission in a single channel, the DSR reduces to (1/''T'')log2''n''; with a two-condition modulation, i. e. ''n'' = 2, the DSR is 1/''T'', according to Hartley's law. # For parallel transmission with equal unit intervals and equal numbers of significant conditions on each channel, the DSR is (''m''/''T'')log2''n''; in the case of a two-condition modulation, this reduces to ''m''/''T''. # The DSR may be expressed in bauds, in which case, the factor log2''ni'' in ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
64b/66b Encoding
In data networking and transmission, 64b/66b is a line code that transforms 64- bit data to 66-bit line code to provide enough state changes to allow reasonable clock recovery and alignment of the data stream at the receiver. It was defined by the IEEE 802.3 working group as part of the IEEE 802.3ae-2002 amendment which introduced 10 Gbit/s Ethernet. At the time 64b/66b was deployed, it allowed 10 Gb Ethernet to be transmitted with the same lasers used by SONET OC-192, rather than requiring the 12.5 Gbit/s lasers that were not expected to be available for several years. The protocol overhead of a coding scheme is the ratio of the number of raw payload bits to the number of raw payload bits plus the number of added coding bits. The overhead of 64b/66b encoding is 2 coding bits for every 64 payload bits or 3.125%. This is a considerable improvement on the 25% overhead of the previously-used 8b/10b encoding scheme, which added 2 coding bits to every 8 payload bits. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SerDes Framer Interface
SerDes Framer Interface is a standard for telecommunications abbreviated as SFI. Variants include: * SFI-4 or SerDes Framer Interface Level 4, a standardized Electrical Interface by the Optical Internetworking Forum (OIF) for connecting a synchronous optical networking (SONET) framer component to an optical serializer/deserializer (SerDes) for Optical Carrier transmission rate OC-192 interfaces at about 10 Gigabits per second. * SFI-5 or SerDes Framer Interface Level 5, a standardized Electrical Interface by the OIF for connecting a SONET Framer component to an optical SerDes for OC-768, about 40 Gbit/s. Electrically, it consists of 16 pairs of SerDes channels each running at 3.125 Gbit/s which gives an aggregate bandwidth of 50 Gbit/s accommodating up to 25% of Forward Error Correction See also * XFP transceiver The XFP (10 gigabit small form-factor pluggable) is a standard for transceivers for high-speed computer network and telecommunication links that use optic ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
XAUI
10 Gigabit Attachment Unit Interface (XAUI ) is a standard for extending the XGMII (10 Gigabit Media Independent Interface) between the MAC and PHY layer of 10 Gigabit Ethernet (10GbE) defined in Clause 47 of the IEEE 802.3 standard. The name is a concatenation of the Roman numeral X, meaning ten, and the initials of " Attachment Unit Interface". The purpose of the XGMII Extender, which is composed of an XGXS (XGMII Extender Sublayer) at the MAC end, an XGXS at the PHY end and a XAUI between them, is to extend the operational distance of the XGMII and to reduce the number of interface signals. Applications include extending the physical separation possible between MAC and PHY components in a 10 Gigabit Ethernet system distributed across a circuit board. Operation XGMII Extender has the following characteristics: * Simple signal mapping to the XGMII * Independent transmit and receive data paths * Four lanes conveying the XGMII 32-bit data and control * Differential signaling wit ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
19-inch Rack
A 19-inch rack is a standardized frame or enclosure for mounting multiple electronic equipment modules. Each module has a front panel that is wide. The 19 inch dimension includes the edges or "ears" that protrude from each side of the equipment, allowing the module to be fastened to the rack frame with screws or bolts. Common uses include computer servers, telecommunications equipment and networking hardware, audiovisual production gear, and scientific equipment. Overview and history Equipment designed to be placed in a rack is typically described as rack-mount, rack-mount instrument, a rack-mounted system, a rack-mount chassis, subrack, rack cabinet, rack-mountable, or occasionally simply shelf. The height of the electronic modules is also standardized as multiples of or one rack unit or U (less commonly RU). The industry-standard rack cabinet is 42U tall; however, 45U racks are also common. The term ''relay rack'' appeared first in the world of telephony. By 1911, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fibre Channel
Fibre Channel (FC) is a high-speed data transfer protocol providing in-order, lossless delivery of raw block data. Fibre Channel is primarily used to connect computer data storage to servers in storage area networks (SAN) in commercial data centers. Fibre Channel networks form a switched fabric because the switches in a network operate in unison as one big switch. Fibre Channel typically runs on optical fiber cables within and between data centers, but can also run on copper cabling. Supported data rates include 1, 2, 4, 8, 16, 32, 64, and 128 gigabit per second resulting from improvements in successive technology generations. The industry now notates this as Gigabit Fibre Channel (GFC). There are various upper-level protocols for Fibre Channel, including two for block storage. Fibre Channel Protocol (FCP) is a protocol that transports SCSI commands over Fibre Channel networks. FICON is a protocol that transports ESCON commands, used by IBM mainframe computers, over Fibr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Small Form-factor Pluggable Transceiver
Small Form-factor Pluggable connected to a pair of fiber-optic cables Small Form-factor Pluggable (SFP) is a compact, hot-pluggable network interface module format used for both telecommunication and data communications applications. An SFP interface on networking hardware is a modular slot for a media-specific transceiver, such as for a fiber-optic cable or a copper cable. The advantage of using SFPs compared to fixed interfaces (e.g. modular connectors in Ethernet switches) is that individual ports can be equipped with different types of transceiver as required. The form factor and electrical interface are specified by a multi-source agreement (MSA) under the auspices of the Small Form Factor Committee. The SFP replaced the larger gigabit interface converter (GBIC) in most applications, and has been referred to as a Mini-GBIC by some vendors. SFP transceivers exist supporting synchronous optical networking (SONET), Gigabit Ethernet, Fibre Channel, PON, and other c ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Enhanced Small Form-factor Pluggable Transceiver
Small Form-factor Pluggable connected to a pair of fiber-optic cables Small Form-factor Pluggable (SFP) is a compact, hot-pluggable network interface module format used for both telecommunication and data communications applications. An SFP interface on networking hardware is a modular slot for a media-specific transceiver, such as for a fiber-optic cable or a copper cable. The advantage of using SFPs compared to fixed interfaces (e.g. modular connectors in Ethernet switches) is that individual ports can be equipped with different types of transceiver as required. The form factor and electrical interface are specified by a multi-source agreement (MSA) under the auspices of the Small Form Factor Committee. The SFP replaced the larger gigabit interface converter (GBIC) in most applications, and has been referred to as a Mini-GBIC by some vendors. SFP transceivers exist supporting synchronous optical networking (SONET), Gigabit Ethernet, Fibre Channel, PON, and other c ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
XENPAK
XENPAK is a multisource agreement (MSA), instigated by Agilent Technologies and Agere Systems, that defines a fiber-optic or wired transceiver module which conforms to the 10 Gigabit Ethernet (10GbE) standard of the Institute of Electrical and Electronics Engineers (IEEE) 802.3 working group. The MSA group received input from both transceiver and equipment manufacturers during the definition process. XENPAK has been replaced by more compact devices providing the same functionality. History The XENPAK MSA was publicly announced on March 12, 2001 and the first revision of the document was publicly released on May 7, 2001. The most recent revision of the MSA, Issue 3.0, was published on September 18, 2002. The result covered all physical media dependent (PMD) types defined by the IEEE at that time for 802.3ae 10GbE. Although the XENPAK agreement received early support, its modules were thought to be overly large for high density applications. , vendors generally changed to use XFP m ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> 19-inch Rack")
