latent heat of fusion

In thermodynamics, the enthalpy of fusion of a substance, also known as (latent) heat of fusion, is the change in its enthalpy resulting from providing energy, typically heat, to a specific quantity of the substance to change its state from a solid to a liquid, at constant pressure.

It is the amount of energy required to convert one mole of solid into liquid For example, when melting 1 kg of ice (at 0 °C under a wide range of pressures), 333.55 kJ of energy is absorbed with no temperature change. The heat of solidification (when a substance changes from liquid to solid) is equal and opposite.

This energy includes the contribution required to make room for any associated change in volume by displacing its environment against ambient pressure. The temperature at which the phase transition occurs is the melting point or the freezing point, according to context. By convention, the pressure is assumed to be unless otherwise specified.

Overview

The 'enthalpy' of fusion is a latent heat, because, while melting, the heat energy needed to change the substance from solid to liquid at atmospheric pressure is latent heat of fusion, as the temperature remains constant during the process. The latent heat of fusion is the enthalpy change of any amount of substance when it melts. When the heat of fusion is referenced to a unit of mass, it is usually called the specific heat of fusion, while the molar heat of fusion refers to the enthalpy change per amount of substance in moles.

The liquid phase has a higher internal energy than the solid phase. This means energy must be supplied to a solid in order to melt it and energy is released from a liquid when it freezes, because the molecules in the liquid experience weaker intermolecular forces and so have a higher potential energy (a kind of bond-dissociation energy for intermolecular forces).

When liquid water is cooled, its temperature falls steadily until it drops just below the line of freezing point at 0 °C. The temperature then remains constant at the freezing point while the water crystallizes. Once the water is completely frozen, its temperature continues to fall.

The enthalpy of fusion is almost always a positive quantity; helium is the only known exception. Helium-3 has a negative enthalpy of fusion at temperatures below 0.3 K. Helium-4 also has a very slightly negative enthalpy of fusion below . This means that, at appropriate constant pressures, these substances freeze with the addition of heat. In the case of ⁴He, this pressure range is between 24.992 and .

{, class="wikitable sortable"
, -
! rowspan=2, Substance
! colspan=2, Heat of fusion
, -
! (cal/g)
! (J/g)
, -
, water
, 79.72
, 333.55
, -
, methane
, 13.96
, 58.99
, -
, propane
, 19.11
, 79.96
, -
, glycerol
, 47.95
, 200.62
, -
, formic acid
, 66.05
, 276.35
, -
, acetic acid
, 45.90
, 192.09
, -
, acetone
, 23.42
, 97.99
, -
, benzene
, 30.45
, 127.40
, -
, myristic acid
, 47.49
, 198.70
, -
, palmitic acid
, 39.18
, 163.93
, -
, sodium acetate
,
, 264–289Ibrahim Dincer and Marc A. Rosen
Thermal Energy Storage: Systems and Applications
page 155
, -
, stearic acid
, 47.54
, 198.91
, -
, gallium
, 19.2
, 80.4
, -
, paraffin wax (C₂₅H₅₂)
, 47.8–52.6
, 200–220

These values are mostly from the CRC ''Handbook of Chemistry and Physics'', 62nd edition. The conversion between cal/g and J/g in the above table uses the thermochemical calorie (cal_th) = 4.184 joules rather than the International Steam Table calorie (cal_INT) = 4.1868 joules.

Examples

Solubility prediction

The heat of fusion can also be used to predict solubility for solids in liquids. Provided an ideal solution is obtained the mole fraction $(x_2)$ of solute at saturation is a function of the heat of fusion, the melting point of the solid $(T_\text{fus})$ and the temperature $(T)$ of the solution:

:$\ln x_2 = - \frac {\Delta H^\circ_\text{fus{R} \left(\frac{1}{T}- \frac{1}{T_\text{fus\right)$

Here, $R$ is the gas constant. For example, the solubility of paracetamol in water at 298 K is predicted to be:

:x_2 = \exp {\left \frac {28100 ~\text{J mol}^{-1 {8.314 ~\text{J K}^{-1} ~\text{mol}^{-1\left(\frac{1}{298 ~\text{K- \frac{1}{442 ~\text{K\right)\right = 0.0248

Since the molar mass of water and paracetamol are and and the density of the solution is , an estimate of the solubility in grams per liter is:

:$\frac{0.0248 \times \frac{1000 ~\text{g L}^{-1{18.0153 ~\text{g mol}^{-1}{1-0.0248} \times 151.17 ~\text{g mol}^{-1} = 213.4 ~\text{g L}^{-1}$

which is a deviation from the real solubility (240 g/L) of 11%. This error can be reduced when an additional heat capacity parameter is taken into account.''Measurement and Prediction of Solubility of Paracetamol in Water-Isopropanol Solution. Part 2. Prediction'' H. Hojjati and S. Rohani Org. Process Res. Dev.; 2006; 10(6) pp 1110–1118; (Article)

Proof

At equilibrium the chemical potentials for the pure solvent and pure solid are identical:

:$\mu^\circ_\text{solid} = \mu^\circ_\text{solution}\,$

or

:$\mu^\circ_\text{solid} = \mu^\circ_\text{liquid} + RT\ln X_2\,$

with $R\,$ the gas constant and $T\,$ the temperature.

Rearranging gives:

:$RT\ln X_2 = -\left(\mu^\circ_\text{liquid} - \mu^\circ_\text{solid}\right)\,$

and since

:$\Delta G^\circ_\text{fus} = \mu^\circ_\text{liquid} - \mu^\circ_\text{solid}\,$

the heat of fusion being the difference in chemical potential between the pure liquid and the pure solid, it follows that

:$RT\ln X_2 = -\left(\Delta G^\circ_\text{fus}\right)\,$

Application of the Gibbs–Helmholtz equation:

:$\left( \frac{\partial \left( \frac{\Delta G^\circ_\text{fus} } {T} \right) } {\partial T} \right)_{p\,} = -\frac {\Delta H^\circ_\text{fus {T^2}$

ultimately gives:

:$\left( \frac{\partial \left( \ln X_2 \right) } {\partial T} \right) = \frac {\Delta H^\circ_\text{fus {RT^2}$

or:

:$\partial \ln X_2 = \frac {\Delta H^\circ_\text{fus {RT^2} \times \delta T$

and with integration:

:$\int^{X_2=x_2}_{X_2 = 1} \delta \ln X_2 = \ln x_2 = \int_{T_\text{fus^T \frac {\Delta H^\circ_\text{fus {RT^2} \times \Delta T$

the end result is obtained:

:$\ln x_2 = - \frac {\Delta H^\circ_\text{fus {R}\left(\frac{1}{T}- \frac{1}{T_\text{fus\right)$

See also

* Heat of vaporization
* Heat capacity
* Thermodynamic databases for pure substances
* Joback method (Estimation of the heat of fusion from molecular structure)
* Latent heat
* Lattice energy
* Heat of dilution

Notes

References

*
*

{{DEFAULTSORT:Enthalpy Of Fusion
Thermodynamic properties
Enthalpy