HOME

TheInfoList



OR:

A ball screw (or ballscrew) is a mechanical
linear actuator A linear actuator is an actuator that creates motion in a straight line, in contrast to the circular motion of a conventional electric motor. Linear actuators are used in machine tools and industrial machinery, in computer peripherals such as ...
that translates rotational motion to linear motion with little
friction Friction is the force resisting the relative motion of solid surfaces, fluid layers, and material elements sliding against each other. There are several types of friction: *Dry friction is a force that opposes the relative lateral motion of ...
. A threaded shaft provides a helical raceway for
ball bearing A ball bearing is a type of rolling-element bearing that uses balls to maintain the separation between the bearing races. The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads. It achieves this ...
s which act as a precision screw. As well as being able to apply or withstand high thrust loads, they can do so with minimum internal friction. They are made to close tolerances and are therefore suitable for use in situations in which high precision is necessary. The ball assembly acts as the nut while the threaded shaft is the screw. In contrast to conventional
leadscrew A leadscrew (or lead screw), also known as a power screw or translation screw,Bhandari, p. 202. is a screw used as a linkage in a machine, to translate turning motion into linear motion. Because of the large area of sliding contact between ...
s, ballscrews tend to be rather bulky, due to the need to have a mechanism to recirculate the balls. Another form of linear actuator based on a rotating rod is the threadless ballscrew, a.k.a. "rolling ring drive". In this design, three (or more) rolling-ring bearings are arranged symmetrically in a housing surrounding a smooth (threadless) actuator rod or shaft. The bearings are set at an angle to the rod, and this angle determines the direction and rate of linear motion per revolution of the rod. An advantage of this design over the conventional ballscrew or leadscrew is the practical elimination of backlash and loading caused by preload nuts.


Applications

Ball screws are used in aircraft and missiles to move control surfaces, especially for electric fly by wire, and in automobile
power steering A power steering is a mechanical device equipped on a motor vehicle that helps drivers steer the vehicle by reducing steering effort needed to turn the steering wheel, making it easier for the vehicle to turn or maneuver at lower speeds. Hydra ...
to translate rotary motion from an electric motor to axial motion of the steering rack. They are also used in
machine tool A machine tool is a machine for handling or machining metal or other rigid materials, usually by cutting, boring, grinding, shearing, or other forms of deformations. Machine tools employ some sort of tool that does the cutting or shaping. Al ...
s,
robot A robot is a machine—especially one programmable by a computer—capable of carrying out a complex series of actions automatically. A robot can be guided by an external control device, or the control may be embedded within. Robots may be ...
s, and precision assembly equipment. High precision ball screws are used in
stepper A stepper is a device used in the manufacture of integrated circuits (ICs) that is similar in operation to a slide projector or a photographic enlarger. ''Stepper'' is short for step-and-repeat camera. Steppers are an essential part of the comp ...
s for semiconductor manufacturing.


History

The ball screw was invented independently by H.M. Stevenson and D. Glenn who were issued in 1898 patents 601,451 and 610,044 respectively. Early precise screwshafts were produced by starting with a low-precision screwshaft, and then
lapping Lapping is a machining process in which two surfaces are rubbed together with an abrasive between them, by hand movement or using a machine. Lapping often follows other subtractive processes with more aggressive material removal as a first ste ...
the shaft with several spring-loaded nut laps. By rearranging and inverting the nut laps, the lengthwise errors of the nuts and shaft were averaged. Then, the very repeatable shaft's pitch is measured against a distance standard. A similar process is sometimes used today to produce reference standard screw shafts, or master manufacturing screw shafts. A ball screw is used to expand the Deployable Tower Assembly (DTA) structure on the
James Webb Space Telescope The James Webb Space Telescope (JWST) is a space telescope which conducts infrared astronomy. As the largest optical telescope in space, its high resolution and sensitivity allow it to view objects too old, distant, or faint for the Hubble Sp ...
.


Description and operation

To maintain their inherent accuracy and ensure long life, great care is needed to avoid contamination with dirt and abrasive particles. This may be achieved by using rubber or leather
bellows A bellows or pair of bellows is a device constructed to furnish a strong blast of air. The simplest type consists of a flexible bag comprising a pair of rigid boards with handles joined by flexible leather sides enclosing an approximately airtig ...
to completely or partially enclose the working surfaces. Another solution is to use a positive pressure of filtered air when they are used in a semi-sealed or open enclosure. While reducing friction, ball screws can operate with some preload, effectively eliminating backlash (slop) between input (rotation) and output ( linear motion). This feature is essential when they are used in computer-controlled motion-control systems, e.g., CNC machine tools and high precision motion applications (e.g., wire bonding).


Advantages

Low friction in ball screws yields high mechanical efficiency compared to alternatives. A typical ball screw may be 90 percent efficient, versus 20 to 25 percent efficiency of an Acme lead screw of equal size. Lack of sliding friction between the nut and screw lends itself to extended lifespan of the screw assembly (especially in no-backlash systems), reducing downtime for maintenance and parts replacement, while also decreasing demand for lubrication. This, combined with their overall performance benefits and reduced power requirements, may offset the initial costs of using ball screws. Ball screws may also reduce or eliminate backlash common in lead screw and nut combinations. The balls may be preloaded so that there is no "wiggle" between the ball screw and ball nut. This is particularly desirable in applications where the load on the screw varies quickly, such as machine tools.


Disadvantages

Depending upon their lead angle, ball screws can be back-driven due to their low internal friction (i.e., the screw shaft can be driven linearly to rotate the ball nut). They are usually undesirable for hand-fed
machine tool A machine tool is a machine for handling or machining metal or other rigid materials, usually by cutting, boring, grinding, shearing, or other forms of deformations. Machine tools employ some sort of tool that does the cutting or shaping. Al ...
s, as the stiffness of a servomotor is required to keep the cutter from grabbing the work and self-feeding, that is, where the cutter and workpiece exceed the optimum feedrate and effectively jam or crash together, ruining the cutter and workpiece. Cost is also a major factor as
Acme Acme is Ancient Greek (ακμή; English transliteration: ''akmē'') for "the peak", "zenith" or "prime". It may refer to: Arts and entertainment * ''Acme'' (album), an album by the Jon Spencer Blues Explosion * Acme and Septimius, a fictional ...
screws are cheaper to manufacture.


Manufacture

Ball screw shafts may be fabricated by rolling, yielding a less precise, but inexpensive and mechanically efficient product. Rolled ball screws have a positional precision of several thousandths of an inch per foot.


Accuracy

High-precision screw shafts are typically precise to one thousandth of an inch per foot (830 nanometers per centimeter) or better. They have historically been machined to gross shape, case-hardened, and then ground. The three step process is needed because high temperature machining distorts the work-piece. Hard whirling is a recent (2008) precision machining technique that minimizes heating of the work, and can produce precision screws from case-hardened bar stock. Instrument quality screw shafts are typically precise to 250 nanometers per centimeter. They are produced on precision milling machines with optical distance measuring equipment and special tooling. Similar machines are used to produce optical lenses and mirrors. Instrument screw shafts are generally made of Invar, to prevent temperature from changing tolerances too much. Ball screw are classified using "accuracy grades" from C0 (most precise) to C10.


Ball return systems

The circulating balls travel inside the thread form of the screw and nut, and balls are recirculated through various types of return mechanisms. If the ball nut did not have a return mechanism the balls would fall out of the end of the ball nut when they reached the end of the nut. For this reason several different recirculation methods have been developed. An external ballnut employs a stamped tube which picks up balls from the raceway by use of a small pick-up finger. Balls travel inside the tube and are then replaced back into the thread raceway. An internal button ballnut employs a
machined Machining is a process in which a material (often metal) is cut to a desired final shape and size by a controlled material-removal process. The processes that have this common theme are collectively called subtractive manufacturing, which utilizes ...
or
cast Cast may refer to: Music * Cast (band), an English alternative rock band * Cast (Mexican band), a progressive Mexican rock band * The Cast, a Scottish musical duo: Mairi Campbell and Dave Francis * ''Cast'', a 2012 album by Trespassers William ...
button style return which allows balls to exit the raceway track and move one thread then reenter the raceway. An endcap return ball nut employs a cap on the end of the ball nut. The cap is machined to pick up balls coming out of the end of the nut and direct them down holes which are
bored In conventional usage, boredom, ennui, or tedium is an emotional and occasionally psychological state experienced when an individual is left without anything in particular to do, is listlessness and dissatisfaction arising from a lack of occup ...
transversely down the ballnut. The complement cap on the other side of the nut directs balls back into the raceway. The returning balls are not under significant mechanical load and the return path may incorporate injection moulded low-friction
plastic Plastics are a wide range of synthetic or semi-synthetic materials that use polymers as a main ingredient. Their plasticity makes it possible for plastics to be moulded, extruded or pressed into solid objects of various shapes. This adapta ...
parts.


Thread profile

To obtain proper rolling action of the balls, as in a standard ball bearing, it is necessary that, when loaded in one direction, the ball makes contact at one point with the nut, and one point with the screw. In practice, most ball screws are designed to be lightly preloaded, so that there is at least a slight load on the ball at four points, two in contact with the nut and two in contact with the screw. This is accomplished by using a thread profile that has a slightly larger radius than the ball, the difference in radii being kept small (e.g. a simple V thread with flat faces is unsuitable) so that elastic deformation around the point of contact allows a small, but non-zero contact area to be obtained, like any other rolling element bearing. To this end, the threads are usually machined as a "gothic arch" profile. If a simple semicircular thread profile were used, contact would only be at two points, on the outer and inner edges, which would not resist axial loading.


Preloading

To remove backlash and obtain the optimum stiffness and wear characteristics for a given application, a controlled amount of preload is usually applied. This is accomplished in some cases by machining the components such that the balls are a "tight" fit when assembled, however this gives poor control of the preload, and cannot be adjusted to allow for wear. It is more common to design the ball nut as effectively two separate nuts which are tightly coupled mechanically, with adjustment by either rotating one nut with respect to the other, so creating a relative axial displacement, or by retaining both nuts tightly together axially and rotating one with respect to the other, so that its set of balls is displaced axially to create the preload.


Equations

:T=\frac with the rotary input driving in the conventional way, or :F=\frac if the linear force is backdriving the system Where \mathit is torque applied to screw or nut, \mathit is linear force applied, \mathit is ball screw lead, and \nu is ball screw efficiency. Selection of the standard to be used is an agreement between the supplier and the user and has some significance in the design of the screw. In the United States, ASME has developed the B5.48-1977 Standard entitled "Ball Screws".


See also

* * * * * * *


References

{{Gears Actuators Screws