Applications
There are now about 21,000 desalination plants in operation around the globe. The biggest ones are in the United Arab Emirates, Saudi Arabia, and Israel. The world's largest desalination plant is located in Saudi Arabia ( Ras Al-Khair Power and Desalination Plant) with a capacity of 1,401,000 cubic meters per day. Desalination is currently expensive compared to most alternative sources of water, and only a very small fraction of total human use is satisfied by desalination. It is usually only economically practical for high-valued uses (such as household and industrial uses) in arid areas. However, there is growth in desalination for agricultural use and highly populated areas such as Singapore or California. The most extensive use is in the Persian Gulf. While noting costs are falling, and generally positive about the technology for affluent areas in proximity to oceans, a 2004 study argued, "Desalinated water may be a solution for some water-stress regions, but not for places that are poor, deep in the interior of a continent, or at high elevation. Unfortunately, that includes some of the places with the biggest water problems.", and, "Indeed, one needs to lift the water by 2000 m, or transport it over more than 1600 km to get transport costs equal to the desalination costs. Thus, it may be more economical to transport fresh water from somewhere else than to desalinate it. In places far from the sea, like New Delhi, or in high places, like Mexico City, transport costs could match desalination costs. Desalinated water is also expensive in places that are both somewhat far from the sea and somewhat high, such as Riyadh and Harare. By contrast in other locations transport costs are much less, such as Beijing, Bangkok, Zaragoza, Phoenix, and, of course, coastal cities like Tripoli." After desalination atTechnologies
Desalination is an artificial process by which saline water (generally sea water) is converted to fresh water. The most common desalination processes are distillation and reverse osmosis. There are several methods. Each has advantages and disadvantages but all are useful. The methods can be divided into membrane-based (e.g., reverse osmosis) and thermal-based (e.g., multistage flash distillation) methods. The traditional process of desalination is distillation (i.e., boiling and re- condensation of seawater to leave salt and impurities behind). There are currently two technologies with a large majority of the world's desalination capacity: multi-stage flash distillation and reverse osmosis.Distillation
Solar distillation
Natural evaporation
Water can evaporate through several other physical effects besides solar irradiation. These effects have been included in a multidisciplinary desalination methodology in the IBTS Greenhouse. The IBTS is an industrial desalination (power)plant on one side and a greenhouse operating with the natural water cycle (scaled down 1:10) on the other side. The various processes of evaporation and condensation are hosted in low-tech utilities, partly underground and the architectural shape of the building itself. This integrated biotectural system is most suitable for large scale desert greening as it has a km2 footprint for the water distillation and the same for landscape transformation in desert greening, respectively the regeneration of natural fresh water cycles.Vacuum distillation
In vacuum distillation atmospheric pressure is reduced, thus lowering the temperature required to evaporate the water. Liquids boil when the vapor pressure equals the ambient pressure and vapor pressure increases with temperature. Effectively, liquids boil at a lower temperature, when the ambient atmospheric pressure is less than usual atmospheric pressure. Thus, because of the reduced pressure, low-temperature "waste" heat from electrical power generation or industrial processes can be employed.Multi-stage flash distillation
Water is evaporated and separated from sea water through multi-stage flash distillation, which is a series of flash evaporations. Each subsequent flash process utilizes energy released from the condensation of the water vapor from the previous step.Multiple-effect distillation
Multiple-effect distillation (MED) works through a series of steps called "effects". Incoming water is sprayed onto pipes which are then heated to generate steam. The steam is then used to heat the next batch of incoming sea water. To increase efficiency, the steam used to heat the sea water can be taken from nearby power plants. Although this method is the most thermodynamically efficient among methods powered by heat, a few limitations exist such as a max temperature and max number of effects.Vapor-compression distillation
Vapor-compression evaporation involves using either a mechanical compressor or a jet stream to compress the vapor present above the liquid. The compressed vapor is then used to provide the heat needed for the evaporation of the rest of the sea water. Since this system only requires power, it is more cost effective if kept at a small scale.Wave-powered desalination
Wave powered desalination systems generally convert mechanical wave motion directly to hydraulic power for reverse osmosis. Such systems aim to maximize efficiency and reduce costs by avoiding conversion to electricity, minimizing excess pressurization above the osmotic pressure, and innovating on hydraulic and wave power components. One such example is CETO, a wave power technology that desalinates seawater using submerged buoys. Wave-powered desalination plants began operating on Garden Island in Western Australia in 2013 and in Perth in 2015.Membrane distillation
Membrane distillation uses a temperature difference across a membrane to evaporate vapor from a brine solution and condense pure water on the colder side. The design of the membrane can have a significant effect on efficiency and durability. A study found that a membrane created via co-axialOsmosis
Reverse osmosis
The leading process for desalination in terms of installed capacity and yearly growth is reverse osmosis (RO). The RO membrane processes use semipermeable membranes and applied pressure (on the membrane feed side) to preferentially induce water permeation through the membrane while rejecting salts. Reverse osmosis plant membrane systems typically use less energy than thermal desalination processes. Energy cost in desalination processes varies considerably depending on water salinity, plant size and process type. At present the cost of seawater desalination, for example, is higher than traditional water sources, but it is expected that costs will continue to decrease with technology improvements that include, but are not limited to, improved efficiency, reduction in plant footprint, improvements to plant operation and optimization, more effective feed pretreatment, and lower cost energy sources. Reverse osmosis uses a thin-film composite membrane, which comprises an ultra-thin, aromatic polyamide thin-film. This polyamide film gives the membrane its transport properties, whereas the remainder of the thin-film composite membrane provides mechanical support. The polyamide film is a dense, void-free polymer with a high surface area, allowing for its high water permeability. A recent study has found that the water permeability is primarily governed by the internal nanoscale mass distribution of the polyamide active layer. The reverse osmosis process requires maintenance. Various factors interfere with efficiency: ionic contamination (calcium, magnesium etc.); dissolved organic carbon (DOC); bacteria; viruses; colloids and insoluble particulates;Forward osmosis
Freeze–thaw
Freeze–thaw desalination (or freezing desalination) uses freezing to remove fresh water from salt water. Salt water is sprayed during freezing conditions into a pad where an ice-pile builds up. When seasonal conditions warm, naturally desalinated melt water is recovered. This technique relies on extended periods of natural sub-freezing conditions. A different freeze–thaw method, not weather dependent and invented byElectrodialysis membrane
Electrodialysis utilizes electric potential to move the salts through pairs of charged membranes, which trap salt in alternating channels. Several variances of electrodialysis exist such as conventional electrodialysis,Microbial desalination
Microbial desalination cells are biological electrochemical systems that implements the use of electro-active bacteria to power desalination of water in situ, resourcing the natural anode and cathode gradient of the electro-active bacteria and thus creating an internal supercapacitor.Design aspects
Energy consumption
The energy consumption of the desalination process depends on the salinity of the water. Brackish water desalination requires less energy than seawater desalination. The energy intensity of seawater desalination has improved: It is now about 3 kWh/m3 (in 2018), down by a factor of 10 from 20-30 kWh/m3 in 1970. This is similar to the energy consumption of other fresh water supplies transported over large distances, but much higher than local freshCogeneration
Cogeneration is generating excess heat and electricity generation from a single process. Cogeneration can provide usable heat for desalination in an integrated, or "dual-purpose", facility where a power plant provides the energy for desalination. Alternatively, the facility's energy production may be dedicated to the production of potable water (a stand-alone facility), or excess energy may be produced and incorporated into the energy grid. Cogeneration takes various forms, and theoretically any form of energy production could be used. However, the majority of current and planned cogeneration desalination plants use either fossil fuels or nuclear power as their source of energy. Most plants are located in the Middle East or North Africa, which use their petroleum resources to offset limited water resources. The advantage of dual-purpose facilities is they can be more efficient in energy consumption, thus making desalination more viable. The current trend in dual-purpose facilities is hybrid configurations, in which the permeate from reverse osmosis desalination is mixed with distillate from thermal desalination. Basically, two or more desalination processes are combined along with power production. Such facilities have been implemented in Saudi Arabia at Jeddah and Yanbu. A typical supercarrier in the US military is capable of using nuclear power to desalinate of water per day.Alternatives to desalination
Increased water conservation and efficiency remain the most cost-effective approaches in areas with a large potential to improve the efficiency of water use practices. Wastewater reclamation provides multiple benefits over desalination of saline water, although it typically uses desalination membranes. Urban runoff and storm water capture also provide benefits in treating, restoring and recharging groundwater. A proposed alternative to desalination in the American Southwest is the commercial importation of bulk water from water-rich areas either by oil tankers converted to water carriers, or pipelines. The idea is politically unpopular in Canada, where governments imposed trade barriers to bulk water exports as a result of a North American Free Trade Agreement (NAFTA) claim. The California Department of Water Resources and the California State Water Resources Control Board submitted a report to the state legislature recommending that urban water suppliers achieve an indoor water use efficiency standard of per capita per day by 2023, declining to per day by 2025, and by 2030 and beyond.Costs
Factors that determine the costs for desalination include capacity and type of facility, location, feed water, labor, energy, financing and concentrate disposal. Costs of desalinating sea water (infrastructure, energy, and maintenance) are generally higher than fresh water from rivers orEnvironmental concerns
Intake
In the United States, cooling water intake structures are regulated by the Environmental Protection Agency (EPA). These structures can have the same impacts on the environment as desalination facility intakes. According to EPA, water intake structures cause adverse environmental impact by sucking fish and shellfish or their eggs into an industrial system. There, the organisms may be killed or injured by heat, physical stress, or chemicals. Larger organisms may be killed or injured when they become trapped against screens at the front of an intake structure. Alternative intake types that mitigate these impacts include beach wells, but they require more energy and higher costs. TheOutflow
Desalination processes produce large quantities of brine, possibly at above ambient temperature, and contain residues of pretreatment and cleaning chemicals, their reaction byproducts and heavy metals due to corrosion (especially in thermal-based plants). Chemical pretreatment and cleaning are a necessity in most desalination plants, which typically includes prevention of biofouling, scaling, foaming and corrosion in thermal plants, and of biofouling, suspended solids and scale deposits in membrane plants. To limit the environmental impact of returning the brine to the ocean, it can be diluted with another stream of water entering the ocean, such as the outfall of a wastewater treatment or power plant. With medium to large power plant and desalination plants, the power plant's cooling water flow is likely to be several times larger than that of the desalination plant, reducing the salinity of the combination. Another method to dilute the brine is to mix it via a diffuser in a mixing zone. For example, once a pipeline containing the brine reaches the sea floor, it can split into many branches, each releasing brine gradually through small holes along its length. Mixing can be combined with power plant or wastewater plant dilution. Furthermore, zero liquid discharge systems can be adopted to treat brine before disposal. Another possibility is making the desalination plant movable, thus avoiding that the brine builds up into a single location (as it keeps being produced by the desalination plant). Some such movable (ship-connected) desalination plants have been constructed. Brine is denser than seawater and therefore sinks to the ocean bottom and can damage the ecosystem. Brine plumes have been seen to diminish over time to a diluted concentration, to where there was little to no effect on the surrounding environment. However studies have shown the dilution can be misleading due to the depth at which it occurred. If the dilution was observed during the summer season, there is possibility that there could have been a seasonal thermocline event that could have prevented the concentrated brine to sink to sea floor. This has the potential to not disrupt the sea floor ecosystem and instead the waters above it. Brine dispersal from the desalination plants has been seen to travel several kilometers away, meaning that it has the potential to cause harm to ecosystems far away from the plants. Careful reintroduction with appropriate measures and environmental studies can minimize this problem.Other issues
Due to the nature of the process, there is a need to place the plants on approximately 25 acres of land on or near the shoreline. In the case of a plant built inland, pipes have to be laid into the ground to allow for easy intake and outtake. However, once the pipes are laid into the ground, they have a possibility of leaking into and contaminating nearby aquifers. Aside from environmental risks, the noise generated by certain types of desalination plants can be loud.Health aspects
Iodine deficiency
Desalination removes iodine from water and could increase the risk of iodine deficiency disorders. Israeli researchers claimed a possible link between seawater desalination and iodine deficiency, finding iodine deficits among adults exposed to iodine-poor water concurrently with an increasing proportion of their area's drinking water from seawater reverse osmosis (SWRO). They later found probable iodine deficiency disorders in a population reliant on desalinated seawater. A possible link of heavy desalinated water use and national iodine deficiency was suggested by Israeli researchers. They found a high burden of iodine deficiency in the general population of Israel: 62% of school-age children and 85% of pregnant women fall below the WHO's adequacy range. They also pointed out the national reliance on iodine-depleted desalinated water, the absence of a universal salt iodization program and reports of increased use of thyroid medication in Israel as a possible reasons that the population's iodine intake is low. In the year that the survey was conducted, the amount of water produced from the desalination plants constitutes about 50% of the quantity of fresh water supplied for all needs and about 80% of the water supplied for domestic and industrial needs in Israel.Experimental techniques
Other desalination techniques include:Waste heat
Thermally-driven desalination technologies are frequently suggested for use with low-temperature waste heat sources, as the low temperatures are not useful for process heat needed in many industrial processes, but ideal for the lower temperatures needed for desalination. In fact, such pairing with waste heat can even improve electrical process: Diesel generators commonly provide electricity in remote areas. About 40–50% of the energy output is low-grade heat that leaves the engine via the exhaust. Connecting a thermal desalination technology such as membrane distillation system to the diesel engine exhaust repurposes this low-grade heat for desalination. The system actively cools the diesel generator, improving its efficiency and increasing its electricity output. This results in an energy-neutral desalination solution. An example plant was commissioned by Dutch company Aquaver in March 2014 forLow-temperature thermal
Originally stemming from ocean thermal energy conversion research, low-temperature thermal desalination (LTTD) takes advantage of water boiling at low pressure, even atThermoionic process
In October 2009, Saltworks Technologies announced a process that uses solar or other thermal heat to drive an ionic current that removes all sodium and chlorine ions from the water using ion-exchange membranes.Evaporation and condensation for crops
The Seawater greenhouse uses natural evaporation and condensation processes inside a greenhouse powered by solar energy to grow crops in arid coastal land.Ion concentration polarisation (ICP)
In 2022, using a technique that utilised multiple stages of ion concentration polarisation followed by a single stage of electrodialysis, researchers from MIT manage to create a filterless portable desalination unit, capable of removing both dissolved salts and suspended solids. Designed for use by non-experts in remote areas or natural disasters, as well as on military operations, the prototype is the size of a suitcase, measuring 42 × 33.5 × 19 cm3 and weighing 9.25 kg. The process is fully automated, notifying the user when the water is safe to drink, and can be controlled by a single button or smartphone app. As it does not require a high pressure pump the process is highly energy efficient, consuming only 20 watt-hours per liter of drinking water produced, making it capable of being powered by common portable solar panels. Using a filterless design at low pressures or replacable filters significantly reduces maintenance requirements, while the device itself is self cleaning. However, the device is limited to producing 0.33 liters of drinking water per minute. There are also concerns that fouling will impact the long-term reliability, especially in water with high turbidity. The researchers are working to increase the efficiency and production rate with the intent to commercialise the product in the future, however a significant limitation is the reliance on expensive materials in the current design.Other approaches
Adsorption-based desalination (AD) relies on the moisture absorption properties of certain materials such as Silica Gel.Forward osmosis
One process was commercialized by Modern Water PLC usingHydrogel based desalination
The idea of the method is in the fact that when the hydrogel is put into contact with aqueous salt solution, it swells absorbing a solution with the ion composition different from the original one. This solution can be easily squeezed out from the gel by means of sieve or microfiltration membrane. The compression of the gel in closed system lead to change in salt concentration, whereas the compression in open system, while the gel is exchanging ions with bulk, lead to the change in the number of ions. The consequence of the compression and swelling in open and closed system conditions mimics the reverse Carnot Cycle of refrigerator machine. The only difference is that instead of heat this cycle transfers salt ions from the bulk of low salinity to a bulk of high salinity. Similarly to the Carnot cycle this cycle is fully reversible, so can in principle work with an ideal thermodynamic efficiency. Because the method is free from the use of osmotic membranes it can compete with reverse osmosis method. In addition, unlike the reverse osmosis, the approach is not sensitive to the quality of feed water and its seasonal changes, and allows the production of water of any desired concentration.Small-scale solar
The United States, France and the United Arab Emirates are working to develop practicalPassarell
The Passarell process uses reduced atmospheric pressure rather than heat to drive evaporative desalination. The pure water vapor generated by distillation is then compressed and condensed using an advanced compressor. The compression process improves distillation efficiency by creating the reduced pressure in the evaporation chamber. The compressor centrifuges the pure water vapor after it is drawn through a demister (removing residual impurities) causing it to compress against tubes in the collection chamber. The compression of the vapor increases its temperature. The heat is transferred to the input water falling in the tubes, vaporizing the water in the tubes. Water vapor condenses on the outside of the tubes as product water. By combining several physical processes, Passarell enables most of the system's energy to be recycled through its evaporation, demisting, vapor compression, condensation, and water movement processes.Geothermal
Geothermal energy can drive desalination. In most locations, geothermal desalination beats using scarce groundwater or surface water, environmentally and economically.Nanotechnology
Nanotube membranes of higher permeability than current generation of membranes may lead to eventual reduction in the footprint of RO desalination plants. It has also been suggested that the use of such membranes will lead to reduction in the energy needed for desalination. Hermetic, sulphonated nano-composite membranes have shown to be capable of removing various contaminants to the parts per billion level, and have little or no susceptibility to high salt concentration levels.Biomimesis
BiomimeticElectrochemical
In 2008, Siemens Water Technologies announced technology that applied electric fields to desalinate one cubic meter of water while using only a purported 1.5 kWh of energy. If accurate, this process would consume one-half the energy of other processes. As of 2012 a demonstration plant was operating in Singapore. Researchers at the University of Texas at Austin and the University of Marburg are developing more efficient methods of electrochemically mediated seawater desalination.Electrokinetic shocks
A process employing electrokinetic shock waves can be used to accomplish membraneless desalination at ambient temperature and pressure. In this process, anions and cations in salt water are exchanged for carbonate anions and calcium cations, respectively using electrokinetic shockwaves. Calcium and carbonate ions react to form calcium carbonate, which precipitates, leaving fresh water. The theoretical energy efficiency of this method is on par with electrodialysis and reverse osmosis.Temperature swing solvent extraction
Temperature Swing Solvent Extraction (TSSE) uses a solvent instead of a membrane or high temperatures. Solvent extraction is a common technique in chemical engineering. It can be activated by low-grade heat (less than , which may not require active heating. In a study, TSSE removed up to 98.4 percent of the salt in brine. A solvent whose solubility varies with temperature is added to saltwater. At room temperature the solvent draws water molecules away from the salt. The water-laden solvent is then heated, causing the solvent to release the now salt-free water. It can desalinate extremely salty brine up to seven times as salty as the ocean. For comparison, the current methods can only handle brine twice as salty.Wave energy
A small-scale offshore system uses wave energy to desalinate 30-50 m3/day. The system operates with no external power, and is constructed of recycled plastic bottles.Plants
Trade Arabia claims Saudi Arabia to be producing 7.9 million cubic meters of desalinated water daily, orIn nature
Evaporation of water over the oceans in the water cycle is a natural desalination process. The formation of sea ice produces ice with little salt, much lower than in seawater. Seabirds distill seawater usingHistory
Desalination has been known to history for millennia as both a concept, and later practice, though in a limited form. The ancient Greek philosopher Aristotle observed in his work '' Meteorology'' that "salt water, when it turns into vapour, becomes sweet and the vapour does not form salt water again when it condenses," and also noticed that a fine wax vessel would hold potable water after being submerged long enough in seawater, having acted as a membrane to filter the salt. There are numerous other examples of experimentation in desalination throughout Antiquity and the Middle Ages, but desalination was never feasible on a large scale until the modern era. A good example of this experimentation are the observations by Leonardo da Vinci (Florence, 1452), who realized that distilled water could be made cheaply in large quantities by adapting a still to a cookstove. During the Middle Ages elsewhere in Central Europe, work continued on refinements in distillation, although not necessarily directed towards desalination. However, it is possible that the first major land-based desalination plant may have been installed under emergency conditions on an island off the coast of Tunisia in 1560. It is believed that a garrison of 700 Spanish soldiers was besieged by a large number of Turks and that, during the siege, the captain in charge fabricated a still capable of producing 40 barrels of fresh water per day, though details of the device have not been reported. Before the Industrial Revolution, desalination was primarily of concern to oceangoing ships, which otherwise needed to keep on board supplies of fresh water. Sir Richard Hawkins (1562-1622), who made extensive travels in the South Seas, reported in his return that he had been able to supply his men with fresh water by means of shipboard distillation. Additionally, during the early 1600s, several prominent figures of the era such as Francis Bacon or Walter Raleigh published reports on water desalination. These reports and others, set the climate for the first patent dispute concerning desalination apparatus. The two first patents regarding water desalination date back to 1675 and 1683 (patents No.184 and No. 226, published by Mr. William Walcot and Mr. Robert Fitzgerald (and others), respectively). Nevertheless, neither of the two inventions was really put into service as a consequence of technical problems derived from scale-up difficulties. No significant improvements to the basic seawater distillation process were made for some time during the 150 years from mid-1600s until 1800. When the frigate '' Protector'' was sold to Denmark in the 1780s (as the ship ''Hussaren'') the desalination plant was studied and recorded in great detail. In the newly formed United States, Thomas Jefferson catalogued heat-based methods going back to the 1500s, and formulated practical advice that was publicized to all U.S. ships on the backs of sailing clearance permits. Beginning about 1800, things started changing very rapidly as consequence of the appearance of the steam engine and the so-called age of steam. The development of a knowledge of the thermodynamics of steam processes and the need for a pure water source for its use in boilers, generated a positive effect regarding distilling systems. Additionally, the spread of European colonialism induced a need for freshwater in remote parts of the world, thus creating the appropriate climate for water desalination. In parallel with the development and improvement of systems using steam ( multiple-effect evaporators), this type of devices quickly demonstrated their potential in the field of desalination. In 1852, Alphonse René le Mire de Normandy, was issued a British patent for a vertical tube seawater distilling unit which thanks to its simplicity of design and ease of construction, very quickly gained popularity for shipboard use.James D. Birkett. History, development and management of water resources – Vol. I. The history of desalination before large-scale use. EOLSS Publications, (2010). Land-based desalting units did not significantly appear until the later half of the nineteenth century. In the 1860s, the US Army purchased three Normandy evaporators, each rated at 7000 gallons/day and installed them on the islands of Key West and Dry Tortugas. Another important land-based desalter plant was installed at Suakin during the 1880s which was able to provide freshwater to the British troops placed there. It consisted of six-effect distillers with a capacity of 350 tons/day. Significant research into improved desalination methods occurred in the United States after World War II. The Office of Saline Water was created in the United States Department of the Interior in 1955 in accordance with the Saline Water Conversion Act of 1952. It was merged into the Office of Water Resources Research in 1974. The first industrial desalination plant in the United States opened in Freeport, Texas in 1961 with the hope of bringing water security to the region after a decade of drought. Vice-president Lyndon B. Johnson attended the plant's opening on June 21, 1961. President John F. Kennedy recorded a speech from theSociety and culture
Despite the issues associated with desalination processes, public support for its development can be very high. One survey of a Southern California community saw 71.9% of all respondents being in support of desalination plant development in their community. In many cases, high freshwater scarcity corresponds to higher public support for desalination development whereas areas with low water scarcity tend to have less public support for its development.See also
* Atmospheric water generator * Dewvaporation * Flexible barge * Peak water * Pumpable ice technology * Soil desalination model * Soil salinity * Soil salinity and groundwater modelReferences
External links