Vetterli rifle

The Vetterli rifles were a series of Swiss army service rifles in use from 1869 to 1889,Barnes, p.196, "10.4x38R Swiss Vetterli M69/81". when they were replaced with Schmidt–Rubin rifles. Modified Vetterlis were also used by the Italian Army.

The Swiss Vetterli rifles combined the American Winchester Model 1866's tubular magazine with a regular bolt featuring for the first time two opposed rear locking lugs. This novel type of bolt was a major improvement over the simpler Dreyse and Chassepot bolt actions. The Vetterli was also the first repeating bolt-action rifle to feature a self-cocking action and a small caliber bore.

Due to the Swiss Federal Council's early 1866 decision to equip the army with a breechloading repeating rifle, the Vetterli rifles were, at the time of their introduction, the most advanced military rifles in Europe. The Vetterli was the replacement for the Eidgenössischer Stutzer 1851, an Amsler-Milbank metallic cartridge conversion from previous Swiss muzzle-loading rifles.

Repetiergewehr Vetterli, Modell 1867

The model 1867 was the first iteration of Vetterli rifles. It was accepted into service in February 1868. The model 1867, like its successors, featured a 12-round under barrel tubular magazine and bolt action feed system. The primary distinguishing feature of the Model 1867 was the external hammer.

Repetiergewehr Vetterli, Modell 1868

Before the Model 1867 was put into full production, the rifle designer, Johann Friedrich Vetterli, updated the rifle by replacing the external hammer with an internal cocking bolt spring, rounded front barrel band and placing the cleaning rod on the left side of the rifle. It was discovered soon after that the cleaning rod in its current placement was easily damaged and was subsequently moved to the under-barrel position. The model was designated the Model 1869.

Repetiergewehr Vetterli, Modell 1869, 69/71

The 1869 ''Repetiergewehr Vetterli'' ( en, repeating rifle, Vetterli) was the first iteration of Vetterli rifles to go into full mass production. It was designed by Johann-Friedrich Vetterli (1822–1882), a Swiss riflemaker, who worked in France and England before becoming director of the Schweizerische Industrie Gesellschaft's armament factory in Neuhausen Switzerland. He also adapted his rifle into a single-shot centerfire variant procured by the Italian Army. In 1871 the Model 1869 was updated by removing the loading gate and magazine cutoff switch. This change was designated the Model 1869/71

Repetiergewehr Vetterli, Modell 1871

Even while manufacture of the M1869/71 was underway, a new 1871 model was put into production. It omitted some redundant parts and featured a modified sight as well as a stronger barrel and stronger iron hoops.

Repetierstutzer Vetterli, Modell 1871

The ''Stutzer'' (carbine) variant of the 1871 rifle was used to equip the ''Scharfschützen'' (sniper) companies of the army. The Stutzer were equipped with a sensitive ''Stecher'' ( double set trigger) action and featured a shorter barrel.

Kavallerie-Repetierkarabiner Vetterli, Modell 1871

The ''Kavallerie-Repetierkarabiner'' ( en, cavalry repeating carbine) was another shortened variant of the 1871 rifle for use by the cavalry, which at that time was still armed with percussion pistols.

Repetiergewehr and -stutzer Vetterli, Modell 1878 and 1881

To accelerate the sluggish production of the Vetterli rifles, the federal authorities built a new arms factory in Berne, the ''Eidgenössische Waffenfabrik'' ( W+F), in 1875. That factory produced the 1878 variant of the Vetterli rifle. Its some 25 improvements included a new bayonet and lug, improved sights and a finger hook on the trigger guard. A ''Stutzer'' variant with a ''Stecher'' action, but otherwise identical to the rifle, was also produced.

M1870 Italian Vetterli

The Italian Army adopted a modified Vetterli design, however as a single-shot, in 1870. Unlike the Swiss model, it was chambered for a centrefire cartridge, the 10.35×47mmR.

M1870/87 Italian Vetterli-Vitali

In 1887, the Italian military updated its single-shot Model 1870 Vetterli rifles with a four-round Vitali box magazine

M1870/87/15 Italian Vetterli

During World War I, like many nations, Italy faced a shortage of modern infantry rifles. As a stop-gap measure, hundreds of thousands of Vetterli-Vitali rifles and a few carbines and musquetoons were converted in Rome and Gardone to fire the 6.5x52mm Carcano round, by adding a 6.5mm barrel liner and a Carcano-style magazine. These conversions were never meant for extended firing with standard 6.5x52mm loads, as the smokeless powder 6.5×52mm cartridge generates higher pressure than the black powder 10.35×47mmR.

Coal Wars

During the Coal Wars, a series of U.S. labor conflicts, Vetterli rifles were sought after not only as a bear rifle but as a self defense rifle called the "poor man’s bear gun”. During the Battle of Blair Mountain, Vetterli rifles were often used by coal miners as combat rifles.

Civilian use

Surplus Vetterli rifles were used in "surprising number" by civilians in the U.S. for hunting deer through 1972.

References

*

Swiss Vetterli rifles
on ''militaryrifles.com''
* NRA research regarding th
weapons
of Blair Mountain

External links

{{Commons category-inline, Vetterli rifle



Rifles of Switzerland
Early rifles
Military history of Switzerland
Science and technology in Switzerland
Military history of Italy
Military history of Russia