Transmission (mechanics)

A transmission (also called a gearbox) is a mechanical device invented by Louis Renault (who founded Renault) which uses a gear set—two or more gears working together—to change the speed, direction of rotation, or torque multiplication/reduction in a machine.

Transmissions can have a single fixed-gear ratio, multiple distinct gear ratios, or continuously variable ratios. Variable-ratio transmissions are used in all sorts of machinery, especially vehicles.

Applications

Early uses

Early transmissions included the right-angle drives and other gearing in windmills, horse-powered devices, and steam-powered devices. Applications of these devices included pumps, mills and hoists.

Bicycles

Bicycles traditionally have used hub gear or Derailleur gear transmissions, but there are other more recent design innovations.

Automobiles

Since the torque and power output of an internal combustion engine (ICE) varies with its rpm, automobiles powered by ICEs require multiple gear ratios to keep the engine within its power band to produce optimal power, fuel efficiency, and smooth operation. Multiple gear ratios are also needed to provide sufficient acceleration and velocity for safe and reliable operation at modern highway speeds. ICEs typically operate over a range of approximately 600–7000 rpm, while the vehicle's speeds requires the wheels to rotate in the range of 0–1800 rpm.

In the early mass-produced automobiles, the standard transmission design was manual: the combination of gears was selected by the driver through a lever (the gear stick) that displaced gears and gear groups along their axes. Starting in 1939, cars using various types of automatic transmission became available in the US market. These vehicles used the engine's own power to change the effective gear ratio depending on the load so as to keep the engine running close to its optimal rotation speed. Automatic transmissions now are used in more than two thirds of cars globally, and on almost all new cars in the US.

Most currently-produced passenger cars with gasoline or diesel engines use transmissions with 4–10 forward gear ratios (also called speeds) and one reverse gear ratio. Electric vehicles typically use a fixed-gear or two-speed transmission with no reverse gear ratio, as electric motors can operate at a wider range of RPM, and provide their full torque even when close to 0 RPM. Reversing the motor is achieved electrically.

Motorcycles

Fixed-ratio

The simplest transmissions used a fixed ratio to provide either a gear reduction or increase in speed, sometimes in conjunction with a change in the orientation of the output shaft. Examples of such transmissions are used in helicopters and wind turbines. In the case of a wind turbine, the first stage of the gearbox is usually a planetary gear, to minimize the size while withstanding the high torque inputs from the turbine.

Multi-ratio

Many transmissions – especially for transportation applications – have multiple gears that are used to change the ratio of input speed (e.g. engine rpm) to the output speed (e.g. the speed of a car) as required for a given situation. Gear (ratio) selection can be manual, semi-automatic, or automatic.

Manual

A manual transmission requires the driver to manually select the gears by operating a gear stick and clutch (which is usually a foot pedal for cars or a hand lever for motorcycles).

Most transmissions in modern cars use synchromesh to synchronise the speeds of the input and output shafts. However, prior to the 1950s, most cars used non-synchronous transmissions.

File:John Deere 3350 tractor cut transmission.JPG , 16-speed tractor transmission (plus 8 reverse gears)
File:M5OD transmission.jpg, Mazda M5OD manual transmission (viewed from the engine side)
File:Gearbox 4gears sequential.gif, Animation of a 4-speed sequential manual transmission

Sequential manual

A sequential manual transmission is a type of non-synchronous transmission used mostly for motorcycles and racing cars. It produces faster shift times than synchronized manual transmissions, through the use of dog clutches rather than synchromesh. Sequential manual transmissions also restrict the driver to selecting either the next or previous gear, in a successive order.

Semi-automatic

A semi-automatic transmission is where some of the operation is automated (often the actuation of the clutch), but the driver's input is required to move off from a standstill or to change gears.

Automated manual / clutchless manual

An automated manual transmission (AMT) is essentially a conventional manual transmission that uses automatic actuation to operate the clutch and/or shift between gears.

Many early versions of these transmissions were semi-automatic in operation, such as '' Autostick'', which automatically control only the clutch, but still require the driver's input to initiate gear changes. Some of these systems are also referred to as ''clutchless manual'' systems. Modern versions of these systems that are fully automatic in operation, such as ''Selespeed'' and '' Easytronic'', can control both the clutch operation and the gear shifts automatically, without any input from the driver.

Automatic

An automatic transmission does not require any input from the driver to change forward gears under normal driving conditions.

Hydraulic automatic

The most common design of automatic transmissions is the hydraulic automatic, which typically uses planetary gearsets that are operated using hydraulics. The transmission is connected to the engine via a torque converter (or a fluid coupling prior to the 1960s), instead of the friction clutch used by most manual transmissions and dual-clutch transmissions.

File:Automatic transmission cut.jpg, Hydraulic automatic transmission (cutaway view)
File:Epicyclic gear ratios.png, Epicyclic gearing diagram, as used in hydraulic automatic transmissions
File:ZF Automatik 6HP26.JPG, Cutaway view of a ZF 6HP hydraulic automatic transmission

Dual-clutch (DCT)

A dual-clutch transmission (DCT) uses two separate clutches for odd and even gear sets. The design is often similar to two separate manual transmissions with their respective clutches contained within one housing, and working as one unit. In car and truck applications, the DCT functions as an automatic transmission, requiring no driver input to change gears.

Continuously-variable Ratio

A continuously variable transmission (CVT) can change seamlessly through a continuous range of gear ratios. This contrasts with other transmissions that provide a limited number of gear ratios in fixed steps. The flexibility of a CVT with suitable control may allow the engine to operate at a constant RPM while the vehicle moves at varying speeds.

CVTs are used in cars, tractors, side-by-sides, motor scooters, snowmobiles, bicycles, and earthmoving equipment.

The most common type of CVT uses two pulleys connected by a belt or chain; however, several other designs have also been used at times.

Noise and vibration

Gearboxes are often a major source of noise and vibration in vehicles and stationary machinery. Higher sound levels are generally emitted when the vehicle is engaged in lower gears. The design life of the lower ratio gears is shorter, so cheaper gears may be used, which tend to generate more noise due to smaller overlap ratio and a lower mesh stiffness etc. than the helical gears used for the high ratios. This fact has been used to analyze vehicle-generated sound since the late 1960s, and has been incorporated into the simulation of urban roadway noise and corresponding design of urban noise barriers along roadways.

See also

* Bicycle gearing
* Direct-drive mechanism
*List of auto parts
* Transfer case

References

{{DEFAULTSORT:Transmission (Mechanics)

Mechanisms (engineering)