History
Snow was described in China, as early as 135 BCE in Han Ying's book ''Disconnection'', which contrasted the pentagonal symmetry of flowers with the hexagonal symmetry of snow.Measurement
Snow scientists typically excavate a snow pit within which to make basic measurements and observations. Observations can describe features caused by wind, water percolation, or snow unloading from trees. Water percolation into a snowpack can create flow fingers and ponding or flow along capillary barriers, which can refreeze into horizontal and vertical solid ice formations within the snowpack. Among the measurements of the properties of snowpacks (together with their codes) that the ''International Classification for Seasonal Snow on the Ground'' presents are: *''Height (H)'' is measured vertically from the ground surface, usually in centimeters. *''Thickness (D)'' is snow depth measured at right angles to the slope on inclined snow covers, usually in centimeters. *''Height of snowpack (HS)'' is the total depth of the snowpack, measured vertically in centimetres from base to snow surface. *''Height of new snow (HN)'' is the depth in centimeters of freshly fallen snow that accumulated on a snow board during a period of 24 hours or some other, specified period. *''Snow water equivalent (SWE)'' is the depth of water that would result if the snow mass melted completely, whether over a given region or a confined snow plot, calculated as the product of the snow height in meters times the vertically-integrated density in kilograms per cubic meter. *''Water equivalent of snowfall (HNW)'' is the snow water equivalent of snowfall, measured for a standard observing period of 24 hours or other period. *''Snow strength (Σ)'' whether compressive, tensile, or shear, snow strength can be regarded as the maximum stress snow can withstand without failing or fracturing, expressed in pascals per second, squared. *''Penetrability of snow surface (P)'' is the depth that an object penetrates into the snow from the surface, usually measured with a Swiss rammsonde, or more crudely by a person standing or on skis, in centimeters. *''Surface features (SF)'' describes the general appearance of the snow surface, owing to deposition, redistribution and erosion by wind, melting and refreezing, sublimation and evaporation, and rain. The following processes have the corresponding results: smooth—deposition without wind; wavy—wind deposited snow; concave furrows—melt and sublimation; convex furrows—rain or melt; random furrows—erosion. *''Snow covered area (SCA)'' describes the extent of snow-covered ground, usually expressed as a fraction (%) of the total. *''Slope angle (Φ)'' is the angle measured from the horizontal to the plane of a slope with a clinometer. *''Aspect of slope (AS)'' is the compass direction towards which a slope faces, normal to the contours of elevation, given either degrees from true North N = 0° = 360° or as N, NE, E, SE, S, SW, W, NW. *''Time (t)'' is usually given in seconds for a measurement duration or in longer units to describe the age of snow deposits and layers.Instruments
''Depth'' – Depth of snow is measured with a snowboard (typically a piece of plywood painted white) observed during a six-hour period. At the end of the six-hour period, all snow is cleared from the measuring surface. For a daily total snowfall, four six-hour snowfall measurements are summed. Snowfall can be very difficult to measure due to melting, compacting, blowing and drifting. ''Liquid equivalent by snow gauge'' – The liquid equivalent of snowfall may be evaluated using a snow gauge or with a standardClassification
The ''International Classification for Seasonal Snow on the Ground'' has a more extensive classification of deposited snow than those that pertain to airborne snow. A list of the main categories (quoted together with their codes) comprises: * ''Precipitation particles (PP)'' (See below) * ''Machine-made snow (MM)'' – May be round polycrystalline particles from freezing of very small water droplets from the surface inward or crushed ice particles from crushing and forced distribution * ''Decomposing and fragmented precipitation particles (DF)'' — Decomposition is caused by a decrease of surface area to reduce surface free energy initial break up by light winds. Wind causes fragmentation, packing and rounding of particles. * ''Rounded Grains (RG)'' – Vary from rounded, usually elongated particles of size around 0.25 mm, which are highly sintered. They may be wind packed or faceted rounded, as well. * ''Faceted Crystals (FC)'' – Grow with grain-to-grain vapour diffusion driven by a large temperature gradient is the primary driver of faceted crystals within the dry snowpack. * ''Depth Hoar (DH)'' – Grain-to-grain vapour diffusion driven by large temperature gradient is the primary driver of depth hoar within the dry snowpack. * ''Surface Hoar (SH)'' – Rapid growth of crystals at the snow surface by transfer of water vapor from the atmosphere toward the snow surface, which is cooled by radiative cooling below ambient temperature. *''Melt Forms (MF)'' – Range from clustered round grains of wet snow through melt-freeze rounded polycrystals when water in veins freezes to loosely bonded, fully rounded single crystals and polycrystals.to polycrystals from a surface layer of wet snow that refroze after having been wetted by melt or rainfall. * ''Ice Formations (IF)'' – Encompass the following features: Horizontal layers, resulting from rain or meltwater from the surface percolating into cold snow and refreezing along layer barriers. Vertical fingers of frozen drained water. A basal crust resurgent from melt water ponding above a substrate and freezes. A glaze of ice on the snow surface, resulting from freezing rain on snow. A sun crust from melt water at the surface snow refreezes at the surface due to radiative cooling.Precipitation particles
The classification of frozen particulates extends the prior classifications of Nakaya and his successors and are quoted in the following table: ''All are formed in cloud, except for rime, which forms on objects exposed to supercooled moisture, and some plate, dendrites and stellars, which can form in a temperature inversion under clear sky.''Physical properties
Each such layer of a snowpack differs from the adjacent layers by one or more characteristics that describe its microstructure or density, which together define the snow type, and other physical properties. Thus, at any one time, the type and state of the snow forming a layer have to be defined because its physical and mechanical properties depend on them. The ''International Classification for Seasonal Snow on the Ground'' lays out the following measurements of snow properties (together with their codes): *''Microstructure'' of snow is complex and hard to measure, yet has a critical influence on the thermal, mechanical, and electromagnetic properties of snow. Although there are multiple means for characterizing microstructure, there is no standard method. *''Grain shape'' (''F'' ) includes both natural and artificial depositions, which may have decomposed or include newly formed crystals freeze-thaw or from hoar frost. *''Grain size'' (''E'' ) represents the average size of grains, each measured at its greatest extension, measured in millimetres. *''Snow density'' (''ρs'' ) is the mass per unit volume of snow of a known volume, calculated as kg/m3. Classification runs from very fine at below 0.2 mm to very coarse (2.0–5.0 mm) and beyond. *''Snow hardness'' (''R'' ) is the resistance to penetration of an object into snow. Most snow studies use a fist or fingers for softer snows (very soft through medium) and a pencil (hard) or knife (very hard) below the hardness boundary of ice. *''Liquid water content'' (''LWC'' ) (or ''free-water content'') is the amount of water within the snow in the liquid phase from either melt, rain, or both. Measurements are expressed as a volume or mass fraction in percent. Dry snow has a 0% mean volume fraction. Wet snow 5.5% and soaked is greater than 15%. *''Snow temperature'' (''Ts'' ) is frequently measured at various elevations in and above the snow column: at the ground, at the surface and a reported height above the surface in °C. *''Impurities'' (''J'' ) commonly are dust, sand, soot, acids, organic and soluble materials; each should be fully described and reported as mass fraction (%, ppm). *''Layer thickness'' (''L'' ) of each stratum of a snowpack is measured in cm.Satellite data and analysis
Remote sensing of snowpacks with satellites and other platforms typically includes multi-spectral collection of imagery. Sophisticated interpretation of the data obtained allows inferences about what is observed. The science behind these remote observations has been verified with ground-truth studies of the actual conditions. Satellite observations record a decrease in snow-covered areas since the 1960s, when satellite observations began. In some regions such as China, a trend of increasing snow cover has been observed (from 1978 to 2006). These changes are attributed to global climate change, which may lead to earlier melting and less aea coverage. However, in some areas there may be an increase in snow depth because of higher temperatures for latitudes north of 40°. For the Northern Hemisphere as a whole the mean monthly snow-cover extent has been decreasing by 1.3% per decade. Satellite observation of snow relies on the usefulness of the physical and spectral properties of snow for analysing remotely sensed data. Dietz, et al. summarize this, as follows: *Snow reflects a high proportion of incident radiation in visible wavelengths. *The Earth continuously emits microwave radiation from its surface that can be measured from space using passive microwave sensors. *The use of active microwave data to map snow-cover characteristics is limited by the fact that only wet snow can be recognized reliably. The most frequently used methods to map and measure snow extent, snow depth and snow water equivalent employ multiple inputs on the visible–infrared spectrum to deduce the presence and properties of snow. The National Snow and Ice Data Center (NSIDC) uses the reflectance of visible and infrared radiation to calculate a normalized difference snow index, which is a ratio of radiation parameters that can distinguish between clouds and snow. Other researchers have developed decision trees, employing the available data to make more accurate assessments. One challenge to this assessment is where snow cover is patchy, for example during periods of accumulation or ablation and also in forested areas. Cloud cover inhibits optical sensing of surface reflectance, which has led to other methods for estimating ground conditions underneath clouds. For hydrological models, it is important to have continuous information about the snow cover. Applicable techniques involve interpolation, using the known to infer the unknown. Passive microwaves sensors are especially valuable for temporal and spatial continuity because they can map the surface beneath clouds and in darkness. When combined with reflective measurements, passive microwave sensing greatly extends the inferences possible about the snowpack.Models
Snow science often leads to predictive models that include snow deposition, snow melt, and snow hydrology—elements of the Earth'sGlobal climate change
Global climate change models (GCMs) incorporate snow as a factor in their calculations. Some important aspects of snow cover include its albedo (reflectivity of light) and insulating qualities, which slow the rate of seasonal melting of sea ice. As of 2011, the melt phase of GCM snow models were thought to perform poorly in regions with complex factors that regulate snowmelt, such as vegetation cover and terrain. These models compute snow water equivalent (SWE) in some manner, such as: SWE = c'' )">–ln( 1 – ''fc'' )/ ''D'' where: * ''fc'' = fractional coverage of snow * ''D'' = masking depth of vegetation (≈ 0.2 m worldwide)Snowmelt
Given the importance of snowmelt to agriculture, hydrological runoff models that include snow in their predictions address the phases of accumulating snowpack, melting processes, and distribution of the meltwater through stream networks and into the groundwater. Key to describing the melting processes are solar heat flux, ambient temperature, wind, and precipitation. Initial snowmelt models used a degree-day approach that emphasized the temperature difference between the air and the snowpack to compute snow water equivalent (SWE) as: SWE = ''M'' (''Ta'' – ''Tm'') when ''Ta'' ≥ ''Tm'' ::= 0 when ''Ta'' < ''Tm'' where: *''M'' = melt coefficient *''Ta'' = air temperature *''Tm'' = snowpack temperature More recent models use an energy balance approach that take into account the following factors to compute the energy available for melt (''Qm'') as: ''Qm'' = ''Q*'' +''Qh'' + ''Qe'' + ''Qg'' + ''Qr'' – ''QΘ'' where: *''Q*'' = net radiation *''Qh'' = convective transfer of sensible heat between snowpack and airmass *''Qe'' = latent heat lost through evaporation from or condensation onto the snowpack *''Qg'' = conduction of heat from the ground into the snowpack *''Qr'' = advection of heat through rain *''QΘ'' = rate of change of internal energy per unit of surface area Calculation of the various heat flow quantities (''Q'' ) requires measurement of a much greater range of snow and environmental factors than just temperatures.Engineering
Knowledge gained from science translates into engineering. Four examples are the construction and maintenance of facilities on polar ice caps, the establishment of snow runways, the design of snow tires and ski sliding surfaces. *''Buildings on snow foundations'' – The US Army Cold Regions Research and Engineering Laboratory (CRREL) played a role in assisting theReferences
External links