Manual on Uniform Traffic Control Devices

The ''Manual on Uniform Traffic Control Devices for Streets and Highways'' (usually referred to as the ''Manual on Uniform Traffic Control Devices'', abbreviated MUTCD) is a document issued by the Federal Highway Administration (FHWA) of the United States Department of Transportation (USDOT) to specify the standards by which traffic signs, road surface markings, and signals are designed, installed, and used. Federal law requires compliance by all traffic control signs and surface markings on roads "open to public travel", including state, local, and privately owned roads (but not parking lots or gated communities).Frequently Asked Questions - General Questions on the MUTCD
/ref> While some state agencies have developed their own sets of standards, including their own MUTCDs, these must substantially conform to the federal MUTCD.

The MUTCD defines the content and placement of traffic signs, while design specifications are detailed in a companion volume, ''Standard Highway Signs and Markings''. This manual defines the specific dimensions, colors, and fonts of each sign and road marking. The National Committee on Uniform Traffic Control Devices (NCUTCD) advises FHWA on additions, revisions, and changes to the MUTCD.

The United States is among the countries that have not ratified the Vienna Convention on Road Signs and Signals. The first edition of the MUTCD was published in 1935, 33 years before the Vienna Convention was signed in 1968, and 4 years before World War II started in 1939. The MUTCD differs significantly from the European-influenced Vienna Convention, and an attempt to adopt several of the Vienna Convention's standards during the 1970s led to confusion among many US drivers.

History

At the start of the 20th century—the early days of the rural highway—each road was promoted and maintained by automobile clubs of private individuals, who generated revenue through club membership and increased business along cross-country routes. However, each highway had its own set of signage, usually designed to promote the highway rather than to assist in the direction and safety of travelers. In fact, conflicts between these automobile clubs frequently led to multiple sets of signs—sometimes as many as eleven—being erected on the same highway.

Government action to begin resolving the wide variety of signage that had cropped up did not occur until the late 1910s and early 1920s when groups from Indiana, Minnesota, and Wisconsin began surveying existing road signs in order to develop road signage standards. They reported their findings to the Mississippi Valley Association of Highway Departments, which adopted their suggestions in 1922 for the shapes to be used for road signs. These suggestions included the familiar circular railroad crossing sign and octagonal stop sign.

In January 1927, the American Association of State Highway Officials (AASHO) published the ''Manual and Specifications for the Manufacture, Display, and Erection of U.S. Standard Road Markers and Signs'' to set standards for traffic control devices used on rural roads. Despite the title, this manual did not have any guidance on pavement markings. In the archaic American English of the 1920s, the term "road marker" was sometimes used to describe traffic control devices which modern speakers would now call "signs." In 1930, the National Conference on Street and Highway Safety (NCSHS) published the ''Manual on Street Traffic Signs, Signals, and Markings'', which set similar standards for urban settings, but also added specific guidance on traffic signals, pavement markings, and safety zones. Although the two manuals were quite similar, both organizations immediately recognized that the existence of two slightly different manuals was unnecessarily awkward, and in 1931 AASHO and NCSHS formed a Joint Committee to develop a uniform standard for both urban streets and rural roads. This standard was the MUTCD.

The original edition of the ''Manual on Uniform Traffic Control Devices for Streets and Highways'' was published in 1935. Since that time, subsequent editions of the manual have been published with numerous minor updates occurring between, each taking into consideration changes in usage and size of the nation's system of roads as well as improvements in technology.

In 1942, the Joint Committee was expanded to include the Institute of Transportation Engineers, then known as the Institute of Traffic Engineers. During World War II, the second edition of the MUTCD was released as ''War Emergency Edition''.

In 1948, three years after World War II ended, the third edition of the MUTCD was released. The single most controversial and heavily debated issue during the early years of the MUTCD was the color of center lines on roads. This edition settled the long-running debate in favor of white, and also changed the standard color of stop signs from yellow to red. However, the 1948 MUTCD also allowed for two major exceptions to white center lines: yellow was recommended but not mandatory for double center lines on multi-lane highways and for center lines in no-passing zones.

In 1949, the United Nations Conference on Road and Motor Transport launched a research project to develop a worldwide uniform scheme for highway signs. In 1951, the UN conducted experiments in the U.S. to compare the effectiveness of national traffic sign standards from around the world. Signs from six countries were placed along the road for test subjects to gauge their legibility at a distance. The test strips were located along Ohio State Route 104 near Columbus, U.S. Route 250 and Virginia State Route 53 near Charlottesville, Minnesota State Highway 101 near Minneapolis, and other roads in New York. France, Chile, Turkey, India, and Southern Rhodesia reciprocated by installing MUTCD signs on their roads. In the U.S., the experiments attracted unexpected controversy and curious onlookers who posed a hazard. By September 1951, the experts working on the project were in favor of the American proposals for stop signs (at the time, black "STOP" text on a yellow octagon), "cross road", "left or right curve", and "intersection", but were still struggling to reach consensus on symbols for "narrow road", "bumpy or uneven surface", and "steep hill".

In 1953, after cooperating with the UN conference's initial experiments, the United States declined to sign or ratify the UN's then-proposed protocol for a worldwide system of uniform road signs. There were two major reasons behind this decision. First, most U.S. roads and streets were (and still are) under state jurisdiction. Second, the United States was developing modern controlled-access highways at the time (culminating in the creation of the Interstate Highway System in 1956), and the novel problems presented by such new high-speed highways required rapid innovations in road signing and marking "that would definitely be impaired by adherence to any international code". Despite the Americans' withdrawal from the research project, the experiments eventually resulted in the Vienna Convention on Road Signs and Signals of 1968.

In 1960, the National Joint Committee on Uniform Traffic Control Devices was again reorganized to include representatives of the National Association of Counties and the National League of Cities, then known as the American Municipal Association. In 1961, the MUTCD was again revised to make yellow center lines mandatory for the two exceptions where they had previously been recommended. The 1961 edition was the first edition to provide for uniform signs and barricades to direct traffic around road construction and maintenance operations.

In 1966, Congress passed the Highway Safety Act, , , which is now codified at ''et seq.'' It required all states to create a highway safety program by December 31, 1968, and to adhere to uniform standards promulgated by the U.S. Department of Transportation as a condition of receiving federal highway-aid funds. The penalty for non-compliance was a 10% reduction in funding. In turn, taking advantage of broad rulemaking powers granted in , the Department simply adopted the entire MUTCD by reference at . ((a)(1), also enacted in 1966, authorizes federal agencies to incorporate by reference technical standards published elsewhere, which means the agency may merely cite the standard and need not republish its entire text as part of the appropriate regulation.) Thus, what was formerly a quasi-official project became an official one. States are allowed to supplement the MUTCD but must remain in "substantial conformance" with the national MUTCD and adopt changes within two years after they are adopted by FHWA.

The 1971 edition of the MUTCD included several significant standards. The MUTCD imposed a consistent color code for road surface markings by requiring all center lines dividing opposing traffic on two-way roads to be always painted in yellow (instead of white, which was to always demarcate lanes moving in the same direction), and also required that all highway guide signs (not just those on Interstate Highways) contain white text on a green background.

Another major change, inspired by the Vienna Convention, was that the 1971 MUTCD expressed a preference for a transition to adoption of symbols on signs in lieu of words "as rapidly as public acceptance and other considerations permit." During what was then expected to be a transition period, the MUTCD allowed state highway departments to use optional explanatory word plaques with symbol signs and to continue using the previous standard word message signs in certain cases. Robert Conner, the chief of the traffic control systems division of the Federal Highway Administration during the 1970s, believed that symbol signs were "usually more effective than words in situations where reaction time and comprehension are important." Conner was active in the Joint Committee and also represented the United States at international meetings on road traffic safety. However, several American traffic safety experts were concerned that American drivers would not understand the Vienna Convention's unintuitive symbols, which is why the MUTCD allowed for explanatory word plaques. Available via ProQuest. Most of the repainting to the 1971 standard was done between 1971 and 1974, with a deadline of 1978 for the changeover of both the markings and signage.

The U.S. adoption of several Vienna Convention-inspired symbol signs during the 1970s was a failure. For example, the lane drop symbol sign was criticized as baffling to U.S. drivers—who saw a "big milk bottle"—and therefore quite dangerous, since by definition it was supposed to be used in situations where drivers were about to run out of road and needed to merge into another lane immediately. American highway safety experts ridiculed it as the "Rain Ahead" sign. Many American motorists were bewildered by the Vienna Convention's symbol sign with two children on it, requiring it to be supplemented with a "School Xing" plaque. (The American "School Xing" symbol was later redesigned to depict an adult crossing together with a child.) However, several signs from the Vienna Convention were successfully adopted into the 1971 MUTCD, including the red "Yield" sign, which replaced the previous yellow version, and the "Do Not Enter" sign, which replaced a word-only version. Because the Vienna Convention version was circular, it was given a square backing to conform with the MUTCD shape for regulatory signs, and the words "DO NOT ENTER" were superimposed to ensure American driver comprehension.

The 1971 MUTCD's preference for a rapid transition to symbols over words quietly disappeared in the 1978 MUTCD. The 2000 and 2003 MUTCDs each eliminated a symbol sign that had long been intended to replace a word message sign: "Pavement Ends" (in 2000) and "Narrow Bridge" (in 2003).

The tenth edition of the MUTCD was published in 2009, with revisions in 2012. The Infrastructure Investment and Jobs Act of 2021 requires the USDOT to update the MUTCD quadrennially, and the eleventh edition was released in 2023. This edition allows painted red bus lanes, rules allowing more crosswalks and traffic signals, new rules for determining speed limits, signage for shoulders that are used part-time as traffic lanes, and new signage for electric vehicle charging stations and autonomous vehicles. It also adds painted green bike lanes, bike boxes, and bike-specific traffic lights. Rectangular Rapid-Flashing Beacons (RRFBs) were also added to the MUTCD; a pedestrian beacon for uncontrolled intersections consisting of two rectangular lights, side-by-side, which alternate flashing, under a yellow diamond with a walking person on it, above an arrow pointing out the crosswalk.RIN 2125-AF85 National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for Streets and Highways; Revision
III. Summary of the Major Provisions of the Regulatory Action in Question RRFBs were previously on interim approval by FHWA since March 20, 2018. Transportation safety advocates criticized the changes as not going far enough to deal with a substantial spike in pedestrian fatalities, especially guidance setting speed limits based on the 85th percentile of actual driving speeds.

Development

Proposed additions and revisions to the MUTCD are recommended to FHWA by the National Committee on Uniform Traffic Control Devices (NCUTCD), a private, non-profit organization. The NCUTCD also recommends interpretations of the MUTCD to other agencies that use the MUTCD, such as state departments of transportation. NCUTCD develops public and professional awareness of the principles of safe traffic control devices and practices and provides a forum for qualified individuals to exchange professional information.

The NCUTCD is supported by twenty-one sponsoring organizations, including transportation and engineering industry groups (such as AASHTO and ASCE), safety organizations (such as the National Safety Council and Advocates for Highway and Auto Safety), and the American Automobile Association. Each sponsoring organization promotes members to serve as voting delegates within the NCUTCD.

Adoption

Eighteen states have adopted the national MUTCD as is. Twenty-two states, the District of Columbia, Puerto Rico, and the United States Department of Defense through the Military Surface Deployment and Distribution Command (SDDC) have all adopted supplements to the MUTCD. Ten states have adopted their own editions of the MUTCD "in substantial conformance to" an edition of the national MUTCD, annotated throughout with state-specific modifications and clarifications. The Guam Department of Public Works has also adopted the MUTCD in some form.

The following state-specific MUTCD editions are currently in effect:

* California Department of Transportation: '' California Manual on Uniform Traffic Control Devices'' (CA MUTCD)
* Delaware Department of Transportation: '' Delaware Manual on Uniform Traffic Control Devices'' (DE MUTCD)
* Indiana Department of Transportation: '' Indiana Manual on Uniform Traffic Control Devices'' (IMUTCD)
* Maryland State Highway Administration: '' Maryland Manual on Uniform Traffic Control Devices'' (MdMUTCD)
* Michigan Department of Transportation: '' Michigan Manual on Uniform Traffic Control Devices'' (MMUTCD)
* Minnesota Department of Transportation: '' Minnesota Manual on Uniform Traffic Control Devices'' (MN MUTCD)
* Missouri Department of Transportation: '' Engineering Policy Guide'' (EPG), section 900
* Ohio Department of Transportation: '' Ohio Manual of Uniform Traffic Control Devices'' (OMUTCD)
* Texas Department of Transportation: '' Texas Manual on Uniform Traffic Control Devices'' (TMUTCD)
* Utah Department of Transportation: '' Utah Manual on Uniform Traffic Control Devices'' (Utah MUTCD)

Enforcement

Federal funding is tied to compliance and serves as an enforcement mechanism for state and local governments. For private property owners, FHWA recommends "encouragement" rather than punishment. The use of non-compliant devices can also create liability in tort lawsuits for private owners and some governments.

From 2014 to 2018, New York placed over 500 non-compliant " I Love New York" tourism destination signs along its highways and expressways to encourage tourists to visit nearby destinations, especially those in economically depressed Upstate New York. FHWA contended that the signs violated numerous MUTCD rules, along with the general principle of the MUTCD that signs should be simple so that they are "easy to identify, comprehend and understand in a matter of seconds as you are driving". After FHWA threatened to withhold $14 million in federal funding, New York removed the signs in November 2018.

Other jurisdictions

The United States is among the majority of countries around the world that have not ratified the Vienna Convention on Road Signs and Signals (based primarily on European signage traditions), and the MUTCD differs significantly from the Vienna Convention. Apart from the 1971 effort to adopt several Vienna Convention-inspired symbol signs (as explained above), achieving worldwide uniformity in traffic control devices was never a priority for AASHTO because the number of motorists driving regularly on multiple continents was relatively small during the 20th century.

Warning signs (alerting drivers of unexpected or hazardous conditions) tend to be more verbose than their Vienna Convention counterparts. On the other hand, MUTCD guide signs (directing or informing road users of their location or of destinations) tend to be less verbose, since they are optimized for reading at high speeds on freeways and expressways.

The MUTCD lacks a mandatory sign group like the Vienna Convention does, a separate category for those signs like "Right Turn Only" and "Keep Right" that tell traffic what it must do instead of what it must not do. Instead, the MUTCD primarily classifies them with the other regulatory signs that inform drivers of traffic regulations.

Canada

For road signs in Canada, the Transportation Association of Canada (TAC) publishes its own ''Manual of Uniform Traffic Control Devices for Canada'' for use by Canadian jurisdictions. Although it serves a similar role to the MUTCD, it has been independently developed and has a number of key differences with its US counterpart, most notably the inclusion of bilingual (English/French) signage for jurisdictions such as New Brunswick and Ontario with significant anglophone and francophone population, a heavier reliance on symbols rather than text legends and metric measurements instead of imperial.

The Ministry of Transportation of Ontario (MTO) also has historically used its own MUTCD which bore many similarities to the TAC MUTCDC. However, as of approximately 2000, MTO has been developing the ''Ontario Traffic Manual'' (OTM), a series of smaller volumes each covering different aspects of traffic control (e.g., regulatory signs, warning signs, sign design principles, traffic signals, etc.).

Mexico

Road signs in Mexico are regulated by '' Secretaría de Comunicaciones y Transportes'' Directorate-General for Roads (''Dirección General de Carreteras''), and uniformized under a NOM standard and the ''Manual de Señalización y Dispositivos para el Control de Tránsito en Calles y Carreteras'' (''Manual of Signage and Traffic Control Devices for Streets and Highways''). The signs share many similarities with those used in the United States and Canada. Like Canada but unlike the United States, Mexico has a heavier reliance on symbols than text legends.

Mexico signed the Vienna Convention on Road Signs and Signals on November 8, 1968, but has yet to fully ratify it.

Central America

For road signs in Central American countries, the Central American Integration System (SICA) publishes its own , a Central American equivalent to the US MUTCD. Of the SICA countries, only Costa Rica has signed the Vienna Convention on Road Signs and Signals.

Belize

In Belize, road signs generally follow MUTCD standards. However, there are road signs unique to Belize.

South America and Caribbean

Road signs in South America and Caribbean are generally based on the MUTCD, with the exception of Antigua and Barbuda, French Guiana ( overseas department of France), Dominica, Dutch Caribbean, Grenada, Haiti, Saint Kitts and Nevis, Saint Lucia, Saint Vincent and the Grenadines and Suriname, which use European-style road signs, including triangular warning signs with a red border and a white background as in Europe. Of all the countries in South America, only four countries—Brazil, Chile, Ecuador, and Venezuela—have signed the Vienna Convention on Road Signs and Signals. Chile is also the only country in South America that has ratified this convention.

Argentina

Bolivia

Road signs in Bolivia are regulated by the ''Manuales Técnicos para el Diseño de Carreteras'' standard which is based on the United States's MUTCD (FHWA), Central America's ''Manuales Técnicos para el Diseño de Carreteras'' (SICA), Colombia's ''Manual de Señalización Vial'' (Ministry of Transport), and Chile's ''Manual de Carreteras''. Thus, road signs used in Bolivia generally have many similarities to road signs used in the United States, Central America, Colombia and neighboring Chile.

Brazil

Road signs in Brazil are regulated by ''Manual de Sinalização Rodoviária'' and are based on the MUTCD.

Chile

Road signs in Chile are regulated by ''Manual de Señalización de Tránsito'' and are based on both the MUTCD and the Vienna Convention on Road Signs and Signals. Chile signed the Vienna Convention on Road Signs and Signals on November 8, 1968, and ratified it on December 27, 1974, making it the only country in the Americas to ratify this convention. In Chile, both types of mandatory signs are used: European-style signs with white symbols on a blue background and a white border, signs with black symbols on a white background and a red border.

Colombia

Road signs in Colombia are regulated in the Manual de Señalización Vial standard, which is developed by the Ministry of Transport and based on the United States' MUTCD. Many regulatory signs are based on European signs, i.e. the Vienna Convention on Road Signs and Signals, while many warning signs are based on U.S. and Canadian signs, i.e. on MUTCD

Ecuador

Road signs in Ecuador are regulated in ''Manual Básico de Señalización Vial'' and ''Reglamento Técnico Ecuatoriano. RTE INEN 004-1:2011. Señalización vial''. Signs are, in most ways, similar in design to those used in the United States.

Ecuador signed the Vienna Convention on Road Signs and Signals on November 8, 1968 but has yet to fully ratify it.

Guyana

Road signs in Guyana generally follow the same design as those in the United States and are based on the MUTCD with the exception that some signs are reversed since the country drives on the left. However, most of current signs found in Guyana, are non-compliant with MUTCD standards.

Paraguay

Road signs in Paraguay are regulated in the ''Manual de Carreteras del Paraguay'' standard developed by the Ministry of Public Works and Communications ().

Peru

Road signs in Peru are regulated by the ''Manual de Dispositivos de Control del Tránsito Automotor para Calles y Carreteras'', developed by the Ministry of Transport and Communications of Peru. This standard is based on the United States' ''Manual on Uniform Traffic Control Devices'' (MUTCD) developed by the Federal Highway Administration, Colombia's ''Manual de Señalización Vial'' and Chile's ''Manual de Señalización de Tránsito''. As a result, road signs in Peru are similar in design to those used in the United States on one side and in neighbouring Chile and Colombia on the other side.

Venezuela

Road signs in Venezuela are regulated in ''Manual Venezolano de Dispositivos Uniformes para el Control del Tránsito'' and are based on the United States' MUTCD.

Asia and Oceania

A number of Asian and Oceanian countries use road signages based on the MUTCD. The most notable is Australia, which has a road signage system that is directly based on the MUTCD. Others use a mixture of MUTCD and international standards.

Australia

For road signs in Australia, this is covered by AS 1742 which is unofficially known as ''Manual of Uniform Traffic Control Devices for Australia'', and it serves as a similar role to the MUTCD. As a result, road signs in Australia closely follow those used in U.S., but some sign designs closely follow the ones used in the United Kingdom.

* Australian warning signs have a yellow diamond with a black legend, following America's practice. Australia remains the only country that still has the text-based version of the low-clearance signage. (Most other countries now use vertical arrows in between the clearance height.)
* Australian temporary warning signs are rectangular, following the United Kingdom practice, but they differ from the British temporary warning signs by having a yellow, or an orange background instead.
* Australian regulatory signs are similar to those used in America, except (at least since 1974) the speed limit signs which bear the red circle legend.

The typeface used for Australian road signs is the AS 1744 font which is based on Highway Gothic.

Thailand

Road signs in Thailand are standardized road signs similar to those used in other nations but much of it resembles road signage systems used in South American countries with certain differences, such as using a blue circle instead of a red-bordered white circle to indicate mandatory actions. As a result, Thailand road signage generally have many similarities to road signs used in the United States and Latin American countries.

Thailand is a signatory to the 1968 Vienna Convention on Road Signs and Signals, but has yet to fully ratify the convention.

See also

* Comparison of MUTCD-influenced traffic signs
* Comparison of traffic signs in English-speaking territories
* Road signs in the United States

References

External links

*

National Committee on Uniform Traffic Control Devices
(NCUTCD) website


by H. Gene Hawkins

{{Traffic signs, state=collapsed