List Of GM Bellhousing Patterns

The following is a list of GM bellhousing patterns. Though General Motors has manufactured many different engines, it has kept variance in the bell housing patterns to a relative minimum.

Chevrolet V8 pattern

This was so named because it began with Chevrolet's V8 engines.
* Chevrolet big-block V8s
* Chevrolet small-block V8s
* GM Vortec 4300 90° V6
* GM Iron Duke RWD inline 4 (early RWD Variants, later versions may use a FWD pattern, and have two possible starter locations)
* Jeep with GM Iron Duke inline 4 2.5L/151 in³ (1980-1983). These use a Chrysler custom Torqueflite 904 automatic transmission with an integral Chevrolet bellhousing. Do not confuse with later AMC 2.5 L engine that uses GM small corporate pattern ( see below).
* Chevrolet Turbo-Thrift engine (post-1962)
* Chevrolet 153 Inline 4 (Chevy II, pre- Iron-Duke - includes the Vortec 3000/181 industrial/marine crate motor)
* Detroit Diesel V8 6.2L and 6.5L
* Duramax V8
* Generation III V8s with modifications. These modifications include an additional bolt hole at the top of the pattern, and attachment points for cast oil pans to lower bellhousing extensions, to reduce NVH.

GM metric pattern

:Also called the ''GM small corporate pattern'' and the ''S10 pattern''
This pattern has a distinctive odd-sided hexagonal shape. Rear wheel drive applications have the starter mounted on the right side of the block (when viewed from the flywheel) and on the opposite side of the block compared to front wheel drive installations. The 2.2l S10/Sonoma had the starter located in the same position as front wheel drive cars. A rear wheel drive bellhousing is displayed at right, and the integrated front wheel drive bellhousing is displayed at the lower right (in this case, as a part of the GM 6T70 Transmission).
* GM 60-Degree 2.8/3.1/3.4/3.5/3.9 L V6 (also used by AMC)
* Buick 3300/3800 V6
* Cadillac HT4100/4.5/4.9 L V8
* Isuzu all 3.2 and 3.5L DOHC V6
* AMC/Chrysler 2.5L I4 found in Jeep Cherokee, Comanche, Wagoneer, CJ and Wrangler and Dodge Dakota
* GM Iron Duke/Tech-4 2.5L I4
* GM "122" 1.8/2.0/2.2 L I4
* GM 5.3L LS4 V8
* GM High Value engine

Northstar pattern

Nearly identical to the GM small corporate/metric pattern, except that the starter is located between the cylinder banks, and the lower right bolt hole is moved outward by roughly one inch. Being nearly identical, it too has the distinctive odd-sided hexagonal shape. These engines can be fitted in rear wheel drive vehicles with the right bellhousing and are used in hot rods, kit cars, sand rails and late model engine swaps.
* All Cadillac Northstar V8s
* Oldsmobile Aurora L47 V8
* GM 3.5L LX5 "Short Star" V6

Atlas pattern

Atlas family engines use a unique bellhousing pattern which no other GM motors share.
* GM Atlas engine

Buick Nailhead, Generation 1 pattern

1953-56 Nailheads have a unique round-shaped bellhousing that looks almost the same as bells for the later 1957-66 Nailhead, but in fact the circular flange is about 1" larger.https://www.nailheadbuick.com/transmission-options-for-the-nailhehttps://www.nailheadbuick.com/transmission-adaptors-bell-housings

Buick Nailhead, Generation 2 pattern

1957-66 Nailheads have a unique round-shaped bellhousing that looks almost the same as bells for the earlier 1953-56 Nailhead, but in fact the circular flange is about 1" smaller.

Buick / Rover V8 pattern

*Buick/Oldsmobile/Pontiac 215 Aluminum V-8 (1961-1963)
* Buick 198 V6 (1962-1963)
* Rover V-8 based on the GM 215 (1967-2004)

Buick, Oldsmobile, Pontiac (BOP) V8 pattern

* Post-1965 Oldsmobile/Pontiac RWD V8s
* Buick Big Block V8s (1967-1976) and post-1963 Buick Small Block V8s (1964-1982)
* Buick V6s (225 / 231 / 3.8) (1964-1988)
* Jeep "Dauntless" Buick engines: the 225  V6 (1967-1974) and 350 V8 (1969-1970)
* Cadillac cast iron V8s after 1967 (1968-85 472 and 500, 368 and 425)
* Starters are on the left (driver's) side on Olds 307-455 and Pontiac and the right (passenger) side on Cadillac 425/472/500 and Buick 225/231/3800/300/340/350/400/430/455.

Four bolt holes and two locator pins are common to the Chevrolet and B-O-P patterns. Some transmissions, most notably the TH200-4R, take advantage of this by integrating both specifications into a "universal" bolt pattern casting.

Cadillac V8 pattern, pre-1967

Early Cadillacs manufactured before 1965 used a "round top" bellhousing very similar to early Buicks; around 1965, the bellhousing pattern was revised until the BOP bolt pattern was adopted in 1968.

GM 4-cylinder pattern

* GM Quad-4 family

GM Ecotec 4-cylinder pattern

An example of this pattern can be seen to the right.
* GM Ecotec family (Generation I and II)
* GM LLT and late High Feature family

GM Ecotec Generation III pattern

The completely re-engineered Generation III Ecotec includes a new uniquely shaped bellhousing pattern.

GM High Feature V6 pattern

* Cadilac 2.8
* Holden 3.2
* 3.0 LF1,LFW and 4TH generation LGW,LGY
* 3.6 LY7,LLT,LFX,LWR,LCS,LF3,LF4,LFR,LFY and 4TH generation LGX,LGZ
GM High Feature engine

References

{{Lists of products of US automotive brands

Bellhousing