ISO 261

The ISO metric screw thread is the most commonly used type of general-purpose screw thread worldwide. They were one of the first international standards agreed when the International Organization for Standardization (ISO) was set up in 1947.

The "M" designation for metric screws indicates the nominal outer diameter of the screw thread, in millimetres. This is also referred to as the "major" diameter in the information below. It indicates the diameter of smooth-walled hole that a male thread (e.g. on a bolt) will pass through easily to create a well-located connection to an internally threaded component (e.g. a nut) on the other side. That is, an M6 screw has a nominal outer diameter of 6 millimetres and will therefore be a well-located, co-axial fit in a hole drilled to 6 mm diameter.

Basic profile

The design principles of ISO general-purpose metric screw threads ("M" series threads) are defined in international standard ISO 68-1. Each thread is characterized by its major diameter, ''D'' (''D''_maj in the diagram), and its pitch, ''P''. ISO metric threads consist of a symmetric V-shaped thread. In the plane of the thread axis, the flanks of the V have an angle of 60° to each other. The thread depth is 0.54125 × pitch. The outermost and the innermost of the height ''H'' of the V-shape are cut off from the profile.

The relationship between the height ''H'' and the pitch ''P'' is found using the following equation where ''θ'' is half the included angle of the thread, in this case 30°:

:$H = \frac \cdot P = \frac \cdot P \approx 0.866025 \cdot P$

or

:$P = 2\tan\theta\cdot H = \frac \cdot H \approx 1.154701 \cdot H$

In an external (male) thread (e.g. on a bolt), the major diameter ''D''_maj and the minor diameter ''D''_min define ''maximum'' dimensions of the thread. This means that the external thread must end flat at ''D''_maj, but can be rounded out below the minor diameter ''D''_min. Conversely, in an internal (female) thread (e.g. in a nut), the major and minor diameters are ''minimum'' dimensions; therefore the thread profile must end flat at ''D''_min but may be rounded out beyond ''D''_maj. In practice this means that one can measure the diameter over the threads of a bolt to find the nominal diameter ''D''_maj, and the inner diameter of a nut is ''D''_min.

The minor diameter ''D''_min and effective pitch diameter ''D''_p are derived from the major diameter and pitch as

:\begin
D_\text &= D_\text - 2\cdot\frac58\cdot H = D_\text - \frac\cdot P \approx D_\text - 1.082532 \cdot P \\ pt D_\text &= D_\text - 2\cdot\frac38\cdot H = D_\text - \frac\cdot P \approx D_\text - 0.649519 \cdot P
\end

Designation

A metric ISO screw thread is designated by the letter M followed by the value of the nominal diameter ''D'' (the maximum thread diameter) and the pitch ''P'', both expressed in millimetres and separated by the multiplication sign, ''×'' (e.g. M8×1.25). If the pitch is the normally used "coarse" pitch listed in ISO 261 or ISO 262, it can be omitted (e.g. M8).

The length of a machine screw or bolt is indicated by a following ''×'' and the length expressed in millimetres (e.g. M8×1.25×30 or M8×30).

Tolerance classes defined in ISO 965-1 can be appended to these designations, if required (e.g. M500– 6g in external threads). External threads are designated by lowercase letter, g or h. Internal threads are designated by upper case letters, G or H.

Preferred sizes

ISO 261 specifies a detailed list of preferred combinations of outer diameter ''D'' and pitch ''P'' for ISO metric screw threads.
ISO 262 specifies a shorter list of thread dimensions – a subset of ISO 261.

The thread values are derived from rounded Renard series. They are defined in ISO 3, with "1st choice" sizes being from the Rˈˈ10 series and "2nd choice" and "3rd choice" sizes being the remaining values from the Rˈˈ20 series.

The ''coarse'' pitch is the commonly used default pitch for a given diameter. In addition, one or two smaller ''fine'' pitches are defined, for use in applications where the height of the normal ''coarse'' pitch would be unsuitable (e.g. threads in thin-walled pipes). The terms ''coarse'' and ''fine'' have (in this context) no relation to the manufacturing quality of the thread.

In addition to coarse and fine threads, there is another division of extra fine, or ''superfine'' threads, with a very fine pitch thread. Superfine pitch metric threads are occasionally used in automotive components, such as suspension struts, and are commonly used in the aviation manufacturing industry. This is because extra fine threads are more resistant to coming loose from vibrations. Fine and superfine threads also have a greater minor diameter than coarse threads, which means the bolt or stud has a greater cross-sectional area (and therefore greater load-carrying capability) for the same nominal diameter.

Spanner (wrench) sizes

Below are some common spanner (wrench) sizes for metric screw threads. Hexagonal (generally abbreviated to "hex") head widths (width across flats, spanner size) are for DIN 934 hex nuts and hex head bolts. Other (usually smaller) sizes may occur to reduce weight or cost, including the small series flange bolts defined in ISO 4162 which typically have hexagonal head sizes corresponding to the smaller 1st choice thread size (eg. M6 small series flange bolts have 8mm hexagonal heads, as would normally be found on M5 bolts).

Standards

International

* ISO 68-1: ISO general purpose screw threads — Basic profile — Metric screw threads.
* ISO 261: ISO general purpose metric screw threads — General plan.
* ISO 262: ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts.
* ISO 965: ISO general purpose metric screw threads — Tolerances

** ISO 965-1: Principles and basic data
** ISO 965-2: Limits of sizes for general purpose external and internal screw threads.
** ISO 965-3: Deviations for constructional screw threads
** ISO 965-4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
** ISO 965-5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing

National

* BS 3643: ISO metric screw threads

ANSI/ASME B1.13MMetric Screw Threads: M Profile

ANSI/ASME B4.2-1978 (R2009)
Preferred Metric Limits and Fits

DIN13, page 519

Derived standards

Japan has a JIS metric screw thread standard that largely follows the ISO, but with some differences in pitch and head sizes.

See also

* ASTM A325M
* ASTM F568M
* British Association screw threads (BA)
* British Standard Cycle (BSC)
* British standard fine thread (BSF)
* British standard pipe thread (BSP)
* British Standard Whitworth (BSW) – a British thread standard with 55° profile.
* Buttress thread
* Engineering tolerance
* Garden hose thread
* List of drill and tap sizes
* National pipe thread (NPT)
* National thread
* Nominal size
* ''Panzergewinde''
* Photographic Filter thread
* Preferred metric sizes
* Screw thread
* Square thread form
* Thread angle
* Trapezoidal thread forms
* United States Standard thread
* Unified Thread Standard (UTS, UNC, UNF, UNEF and UNS) – a US/Canadian/British thread standard that uses the same 60° profile as metric threads, but an inch-based set of diameter/pitch combinations.

References

Bibliography

*

External links

Metric screw thread dimensions and tolerances

Metric coarse thread dimensions

Metric fine thread dimensions



Diagrams and tables of many screwthread series. In German

DIN 931: M1,6 to M39 Hexagon head bolts (Product grades A and B)
1987)
* IS 9519: Fasteners - Hexagon products - Width across flats, Indian standard (2013)

{{ISO standards

Thread standards
Screws
ISO 68