Icub Full Body

iCub is a 1 metre tall open source robotics humanoid robot testbed for research into human cognition and artificial intelligence.

It was designed by the RobotCub Consortium of several European universities and built by Italian Institute of Technology, and is now supported by other projects such as ITALK. The robot is open-source, with the hardware design, software and documentation all released under the GPL license. The name is a partial acronym, ''cub'' standing for Cognitive Universal Body. Initial funding for the project was €8.5 million fro
Unit E5
– Cognitive Systems and Robotics – of the European Commission's Seventh Framework Programme, and this ran for 65 months from 1 September 2004 until 31 January 2010.

The motivation behind the strongly humanoid design is the embodied cognition hypothesis, that human-like manipulation plays a vital role in the development of human cognition. A baby learns many cognitive skills by interacting with its environment and other humans using its limbs and senses, and consequently its internal model of the world is largely determined by the form of the human body. The robot was designed to test this hypothesis by allowing cognitive learning scenarios to be acted out by an accurate reproduction of the perceptual system and articulation of a small child so that it could interact with the world in the same way that such a child does.

Specifications

The dimensions of the iCub are similar to that of a 3.5-year-old child. The robot is controlled by an on-board PC104 controller which communicates with actuators and sensors using CANBus.

It utilises tendon driven joints for the hand and shoulder, with the fingers flexed by teflon-coated cable tendons running inside teflon-coated tubes, and pulling against spring returns. Joint angles are measured using custom-designed Hall-effect sensors and the robot can be equipped with torque sensors. The finger tips can be equipped with tactile touch sensors, and a distributed capacitive sensor skin is being developed.

The software library is largely written in C++ and uses YARP for external communication via Gigabit Ethernet with off-board software implementing higher level functionality, the development of which has been taken over by the RobotCub Consortium. The robot was not designed for autonomous operation, and is consequently not equipped with onboard batteries or processors required for this —instead an umbilical cable provides power and a network connection.

In its final version, the robot has 53 actuated degrees of freedom organized as follows:
* 7 in each arm
* 9 in each hand (3 for the thumb, 2 for the index, 2 for the middle finger, 1 for the coupled ring and little finger, 1 for the adduction/abduction)
* 6 in the head (3 for the neck and 3 for the cameras)
* 3 in the torso/waist
* 6 in each leg

The head has stereo cameras in a swivel mounting where eyes would be located on a human and microphones on the side. It also has lines of red LEDs representing mouth and eyebrows mounted behind the face panel for making facial expressions.

Since the first robots were constructed the design has undergone several revisions and improvements, for example smaller and more dexterous hands, and lighter, more robust legs with greater joint angles and which permit walking rather than just crawling.

Capabilities of iCub

The iCub has been demonstrated with capabilities to successfully perform the following tasks, among others:
* crawling, using visual guidance with optic marker on the floor
* solving complex 3D mazes
* archery, shooting arrows with a bow and learning to hit the center of the target
* facial expressions, allowing the iCub to express emotions
* force control, exploiting proximal force/torque sensors
* grasping small objects, such as balls, plastic bottles, etc.
* collision avoidance within non-static environments, as well as, self-collision avoidance

iCubs in the world

These robots were built by Istituto Italiano di Tecnologia (IIT) in Genoa and are used by a small but lively community of scientists that use the iCub to study embodied cognition in artificial systems. There are about thirty iCubs in various laboratories mainly in the European Union but also one in the United States. The first researcher in North America to be granted an iCub was Stephen E. Levinson, for studies of computational models of the brain and mind and language acquisition.

The robots are constructed by IIT and cost about €250,000 each depending upon the version.
Most of the financial support comes from the European Commission's Unit E5 or the Istituto Italiano di Tecnologia (IIT) via the recently created iCub Facility department.
The development and construction of iCub at IIT is part of an independent documentary film called '' Plug & Pray'' which was released in 2010.''Plug & Pray''
documentary film about the social impact of robots and related ethical questions

See also

* Android
* Artificial intelligence
* Cyborg
* Ibn Sina Robot
* Robotics

References

External links

* - Nature article about the iCub.

YouTube Channel
- a YouTube channel about the iCub.

iCub presentations
- from the Humanoid robotics symposium 2010.

IROS'10
- Videos and workshop on iCub research (2010).

Toward Intelligent Humanoids
- Video showing current abilities of the iCub (2012)
*
*

{{sequence
, prev= RobotCub
, list= Humanoid robots
, next=-

Bipedal humanoid robots
2004 robots
Science and technology in Europe
Open-source robots